Power Dynamics 179.120, 179.114, 179.110 Instruction Manual

WIRELESS MICROPHONE SYSTEM

179.120 / 179.114

Instruction Manual

Gebruiksaanwijzing

Gebrauchsanleitung

UK

Thanks for purchasing this product, please read this instruction carefully so that can understand
how to operate the product of style you bought correctly. Please store this instruction in a safe
place after reading as a reference in the future. This series of professional wireless microphone
system used a super steady PLL-synthesized control technique and match with the high efficient,
low consumption discharging technique and the super sensitive discharging receiving technique,
also apply an independent developed mobile frequency compression, expander circuit, image
frequency limiting circuit, a multiple checked silent and noisy circuit, antenna diversity receiving
circuit, switch impact noise defeat circuit. resist reverberation circuit and changed output
controlled slowly system and finished on its item named pattern line. Every system is available to
an excellent electric function by Q C. strictly

Warning

- Always read the manual before using the product.

- Keep the manual so every new user can read it before using the product.

- Always keep the packaging. When a malfunction occurs, please send it in the original

packaging.

- Only for indoor use. Do not use in moistures places.

- Don’t expose to direct sunlight or heat sources.

- Don’t let small objects or fluids enter the housing. This may cause malfunction.

- Clean this unit with a dry cloth. Don’t use cleaning fluids or solvent.

- Unit contains no serviceable parts. Only the replacement parts named in this manual can be

changed by the user or servicing personnel.

- Never open the unit, service may only be done by qualified personnel.

- Never remove or place the mains plug in a socket with wet hands.

- Disconnect the unit from mains power before servicing.

- Condensation water can form while reusing, please let the unit reach the environmental

temperature before using it.

- Keep out of children’s reach.

- When the unit is damaged in a way that internal parts are visible. NEVER connect the unit to

a mains socket and NEVER switch the unit on. In this case, contact your supplier.

- When a lightning storm occurs, always disconnect this unit from the mains socket. Do the

same when the unit won’t or hasn’t be used for a long period of time.

- Using this unit might cause disturbance in insufficiently shielded equipment. This disturbance

might cause damage or accidents. Please check if there is any sensitive equipment in close
proximity of the unit before installing it.

FOREWORD

Your new series of wireless system is designed to give you the best of both sound reinforcement
words, the freedom of wireless system, and the excellent quality. This manual covers each of the
series system.

SYSTEM FEATURE

1. Adopt the PLL-Synthesized control technical, 2x48 selectable UHF channels.

2. The UHF frequency range is 790-812MHz, avoiding the frequency interruption.

3. LCD information display.

4. Fully computerized numerical control, agility and convenience to operate.

5. Double noise squelch operation circuit and system will be higher efficient and much more
steady.

6. Use the dynamic type and Uni-directional cartridge, clear to show the sound.

7. High efficient and low consumption design.

8. Use the high extension antennas, the operating distance will reach 100m.

9. A self-contained input & output connector, convenience to connect the sound equipment

10. Adapt to use in the stage and other occasion.

11. For use in 19”Rack.

SYSTEM TYPE

179.122 UHF hand-held system

179.124 UHF body-pack system

179.106 The hands-free lavaliere microphone.

179.108 The Headset microphone designed for users in physically active applications, who
desire the freedom of hand-free microphone.

179.109 The Guitarist cable designed for use with electric guitars, basses and other electric
instruments.

INTRODUCTION

Hand-held transmitter(compose the handheld microphone system)

Body-pack transmitter (compose the Lavaliere microphone/Guitarist microphone/Headset
microphone system)

Dual channel antenna diversity receiver.

DUAL CHANNEL RECEIVER FEATURES

1. Power Button: Turns the receiver ON/OFF.

2. Power On Indicator: This light on when the receiver is plugged into and electrical outlet
and switch is pushed, it indicates that the receiver is on.

3. Channel A.B Volume Control: Rotate the knob to increase or decrease the volume of the
receiver output.

4. Channel A.B Down Function Button: Sets channel data.

5. Channel A.B Up Function Button: Sets channel data.

6. Channel A.B LCD Information Display: show system frequency/RF signal strength
AF audio level strength ect.

7. Antennas: Supply the RF for receiver.

8. Antenna Input Connectors: Using supplied telescopic antenna or other antenna system.

9. XLR Output Connector: Plug and XLR audio cable from this connector to the input to your
mixer.

10. Squelch Control: Adjust squelch control setting to emphasize either signal quality or
system range. This control is factory pre-set, and normally does not need further
adjustment. Refer to Receiver Squelch adjustment section for more information.

11. Phone Jack Audio Output Connector(Unbalanced high Z): An unbalanced audio cable with
114" phone plug(such as standard guitar cable) can be used between this connector and
your amplifier input.

12. Power Input Connector: Connect the AC adapter to this jack and then plug into an AC
electrical outlet. (Please use supplied AC adapter)

TRANSMITTER FUNCTION & FEATURES

1. Grill: Protects the microphone cartridge and helps reduce wind
noise.

2. LCD information Display: Show the transmitter
power/frequency channel ect.

3. Up Function Button: Sets channel data.

4. Down Function Button: Sets channel data.

5. Power / Mute Button: Power ON/OFF transmitter.

6. Battery: 2 X AA(l.5V) alkaline batteries, or NI-MH rechargeable
battery

7. Battery Cover: Rotate clockwise to close and anti-clockwise to
open.

8. Select the special charger to recharge.

1. Antenna.

2. LCD Information Display: Show the transmitter
power/frequency channel ect.

3. Up Function Button: Sets channel data.

4. Down Function Button: Sets channel data.

5. Power / Mute Button: Power ON/OFF
transmitter.

6. Battery Cover: Open the cover and set

2XAA(1.5V) Alkaline batteries, or NI-MH rechargeable batteries.

7. Antenna Connector.

8. Input Connector: It is TA3 PINS connector; It is suitable for the lavaliere microphones system/ Headset microphone

systems! Guitarist microphone system.

STACKING AND RACK-MOUNTING RECEIVERS

SYSTEM CONNECTIONS

1. Receiver Power Connection: Connect the AC adapter into the DC power connector on the
back of the receiver. Plug the AC adapter into a 220~240VAC/50Hz outlet.

2. Antenna Connection: Attach the two antenna to the ANTENNA connectors.

3. Audio Connection: Connect the audio cable from the audio output on the receiver
to the input on your amplifier equipment.

TRANSMITTER CONNECTIONS

1. Lavalier microphone connection.

2. Headset microphone connection.

3. Guitarist microphone connection.

4. Transmitter Battery Installation: Open the battery cover and insert two AA (1.5V) Alkaline
batteries. (Att. the battery polarity)

RECEIVER OPERATION INSTRUCTION (CHANNEL DATA SETTING)

1. Turn on the receiver

2. Channel Set Up: Press Up and Down button 10 select the channel data.

2.1 Length press "MANU" 10 enter channel setting mode, the figure is flashing, during three
seconds after operation is finished. the system will lock and save the message and then exit.

2.2 Length press "AUTO" to enter Automatic searching mode, when the usable channel is found,
it will be lock and save, and then exit.
Att: When use the "AUTO" mode, the transmitter must be turned on.
NOTE: Overpass the channel setting, the receiver's data is finished, Data will be retained until the
receiver is reset.

OPERATION INSTRUCTION

Turn on the transmitter

1. Length press the power button 10 turn ON/OFF the transmitter, short press the “POWER"
twice, it is turn ON/OFF the MUTE status.

2. Length press "up" to enter frequency selling, the figure is flashing, short press "DOWN", setting
channel to make consistent with the receiver after three seconds it will be exit automatic. Length
press "DOWW, it will show the exchange of frequency and channel.

3.Backlight will light when there are some action for the button, the light will crush out
when the operation is finished.

Length press