Powerbeauty PBB-250, PBB-400, PBB-600 Instruction Manual

INSTRUCTION MANUAL

Article No.:PBB-250/400/600

Specification

- Water resistance of LED lights: IP68 1m

- Light battery: Lithium 3,7V/2000 mAh

- Remote control distance: 3m

- Remote control battery: CR2025 (3V)

- Ambient temperature for operation: 14°C-35°C

- Charging time: 5-6 h

- Battery autonomy (for information only): RGB colours (multicolour): 8 h

Safety instructions
Warning !

Lamps are not toys. Children frequently do not recognize the dangers associated with electric appliances or their packaging. Therefore, you should keep them away from
children.
Keep all products away from any liquid, chemical or heat.
If the lamp is damaged, in particular the cord or the ball discontinues use of the lamp immediately.
Never open the light or attempt to repair the lamp yourself. Improper repairs can endanger the safety of the user.
Never use the external adapter and charger station for purpose other than charging for the light(s) supply in same packing.
The external adapter and the docking/recharging station are only for indoor using, not for outdoor, not exposed to rain, humidity, any liquid or heat.
Don’t use the docking/recharging station or the external adapter for other items or functions.
Keep the external Adapter and the charger station out of reach of children.
Disconnect the external adapter and charging station from power when not used.
Never attempt to open the external adapter, charging station or light bottom.
Lamps may be operated only with the original external adapter.
If you give this lamp to someone else, always include these instructions.

– the battery must be removed from the appliance before it is scrapped;
– the appliance must be disconnected from the supply mains when removing the batte ry;
– the battery is to be disposed of safely.

Caution:

Before placing the light in a pool, remove any floating chemical dispenser.
Never throw the light into the pool. Place the light on the water gently.
Do not put the light in the pool when people are swimming. Take the light out of the pool when not in use.
The care of luminaries is restricted to their surfaces. Use only a dry cloth. Wetness must not get into wiring spaces or to current-carrying parts.
The bulb may not changeable.

Instruction Manual

Charge the light
Before first use, charge the battery for 5-8 hours.

-Place the charger station on a dry and level surface.

-Use clean and dry cloth to clean the surface of the charger station and the bottom of the light

-Insert the adaptor plug into the socket under the charger station. Fig.1.

-Connect the external adapter to the electrical outlet

-Indicator light on charger station lights up in green color.

-Place the light properly on the charging base. It will begin to charge and the indicator light will change to red.

-Indicator light changes back to green when the battery is fully charged.

-After charging, disconnect the external adapter from electrical outlet and remove the light from the station.

Power the light On/Off:

To power on the light, you can either press and hold the button on the bottom of the light.
ON/OFF button for 2 sec. or press the on button on the remote control.
To power off the light, you can either press and hold on the ON/OFF
button for 2 sec. or press the off button on the remote control.

Mode selection by remote control

Note: first remove the small plastic sheet from the battery cover before below operation.

Select color scrolling mode

Once the power is on, press the “PLAY/PAUSE” button, the operation will come into scrolling mode.
the light will illuminate and gradually change though all combinations of colors.
Change to this mode while another mode is in operation, just press, PLAY/PAUSE button on remote control.
While the color is scrolling, you can press button PLAY/PAUSE to hold your favourite color.
For adjustment of light intensity and scrolling speed, refer to following instruction.

Select the individual color mode
After power on, the light will be white color mode. Press the button”COLOR” on the remote control to select 7 individual colors
For adjustment of light intensity and flashing speed, refer to following instruction.

Adjust the light intensity
The initial setting is maximum intensity. While the light is illuminated, press button BRIGHT± on re mote control to reduce the intensity. Pressing at 3 time will get the
minimum intensity. To get higher intensity, press button BRIGHT±again.

Select white and candle mode.
Once the power is on, the light will be in white color. If the light work in another mode, just press the “W HITE”button, the light will be in white
After the power is on, press the “CANDLE” button, the light will be in candle mode.

Adjust the color scrolling speed
The initial setting is SLOW for color scrolling mode . You can press the button “SPEED” to change the speed.

Mode selection by pressing button on the light

Press and hold the button (below) for 2sec. to power on the light.

After power on, the light will start in white color mode, Once the cycle is started to the color mode, it only will go back to white if butt on is held to turn off, then held t o turn back on.

press button as follows:

Press 1st- 7thtimes- select individual Colour
Press 8thtimes-Return to the individual color mode

To Power off the light, press and hold the button for 2 seconds.

Battery replacement (remote control)
If the remote control fails to activate the light, replace the battery.
Press the tab on the side of the battery cover and slide off the cover of the battery from the
remote control.
Take out the battery and replace a new one. Pay attention to the polarity of battery on the cover and cover direction when installing them back to the remote co ntrol.

Warning!

Make sure, that the battery is inserted to the right way and with right polarity.
Remove exhausted battery from the product.
The supply terminals are not be short-circuited
Dispose of battery safely

Caring for your light

Always POWER OFF the light after use.
Use clean water to rinse the light after use, and dry with clean cloth.
Store the light out of reach of children and direct sunlight.

Please contact one of our Product Specialists for assembly assistance
or questions at 1-800-537-8484 or email : [e-mail].
Specialists are available weekdays 8:00AM to 8:00PM EST or
Saturdays 9:30AM to 6:00PM.