6100-43 • 610
Operating Instructions
Hotmelt Applicator
Please read carefully before
attempting operation
Revision : 1
2
8 9
1 6
5
7
3 4
SAFETY INSTRUCTIONS
Do not touch the nozzle or molten adhesive with bare skin as they are
hot - the operating temperature of this tool is approximately 200°C /
392°F (LT 120°C / 248°F). Protective gloves should always be worn.
Careless handling can cause skin burns. If molten adhesive comes into
contact with the skin, immerse the affected area immediately in plenty of cold
water. Seek medical advice if necessary. In addition to the safety instructions
herein, any statutory regulations, local re insurance regulations, or other
generally valid “regulations for accident prevention” must be complied with
when using this tool.
Repairs should only be undertaken by competent personnel with the
adequate electrical knowledge. Before proceeding with any maintenance or
repair operation, disconnect the tool from the mains electricity supply. If in
doubt, contact your supplier.
• WARNING - This tool must be placed on its stand when not in use; do not
leave the tool unattended when switched ON.
• Place the tool on its stand after use and allow it to cool down before storage.
• Never use the tool if it is damaged in any way. If the supply cord is
damaged, it must be replaced by the manufacturer, its service agent or
similar qualied persons in order to avoid a hazard.
• Do not use this tool whilst under the inuence of drugs or alcohol.
• Do not use this tool in damp rooms, and do not expose to rain or moisture.
• Do not use this tool in the vicinity of any heat-sensitive materials, or any
ammable materials, liquids, or gases, and do not apply to the same place
for a long time.
• Only use extension cables with a wire cross-section of 1.5mm² / 16 a.w.g.
and no more than 20m / 65 ft in length.
• Never pull on the tool’s connecting cable.
• This tool is not intended for the use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the tool by a person responsible for their safety.
GUARANTEE AND REPAIRS
This tool is guaranteed against faulty workmanship and
materials for a period of 12 months from the date of purchase.
Within this warranty period the manufacturers undertake, at
their discretion, to either repair or replace any tool proved to
be defective (proof of purchase will be required for verication).
This guarantee is invalidated if the tool is opened, or modied in
any way, or if adhesive formulations other than those supplied by
the tool’s manufacturer are used. Warranty claims attributable
to improper, or careless, use or handling, and to normal wear,
are excluded from this guarantee.
The supplier’s and manufacturer’s only obligation shall be to
replace such tools that are proved to be defective. Neither
supplier nor manufacturer shall be liable for any injury, loss or
damage, direct or consequential, arising out of the use, or the
inability to use, this tool. The user shall determine the suitability
of this product for its intended use, and the user assumes all
risks and liability whatsoever in connection therewith.
The manufacturer reserves the right to improve or modify this
product without prior notice.
Do not connect to the main supply at this point!
AVOIDING PROBLEMS
For help with fault nding, please visit our website:
For optional part, please visit our website:
www.poweradhesives.com
1. Attach the tool stand
2. Connect the air supply
3. Pull the piston back fully and rotate upwards
4. Load 2 adhesive cartridges
5. Rotate the piston down and slide forward
6. Connect to mains supply
7. Red light illuminates
8. Wait 10 minutes
9. Operate trigger to push adhesive forward to the reload
position
10. Reload the tool when the sound of air can be heard
escaping (the piston is now at its most forward point)
11. Adjust the pressure regulator to vary the dispensing rate of
adhesive - ‘+’ increase ow, ‘-’ decrease ow
12. Screw the stand to a table or work surface for extra
stability
13. To switch off the tool, disconnect from the mains supply
• Ensure that tool has reached temperature before
operating.
• Do not leave tool switched on for long periods without use
• If tool is not to be used for more than 40 minutes, switch
off and restart when required.
• Never lay the tool on its side. Always use stand provided,
the optional bench stand or the suspension unit.
• Only use adhesives designed for use with this tool.
1
2
3
4
5
6
7
8
9
Power Adhesives Ltd.
Basildon, Essex, England
SS13 1TN
Telephone: +44 (0) 1268 885 800 Facsimile: +44 (0) 1268 885 810
sales@poweradhesives.com
Loading...