OWNER S MANUAL
Single Preloaded 8.8" Wide Universal
Replacement Headrest Monitor
H-8BK
AV2
M
H-8BG H-8GR H-8GRDK
10
DC 12V
9W
8.8 TFT-LCD
16:9 Wide
1440x234
2AV Inputs(1 AV Input fromfront face)
DC 12V
3W
Right 2.8MHz Left 2.3MHz
Active Matrix TFT
Power Requirements
Power Consumption
Screen Size
Screen Format
Resolution Pixel
A/V Inputs
Dimensions(
With shroud)
IR Power Requirements
IR Power Consumption
IR Transmitter Frequency
LCD Panel Type
Compatible video standard
NTSC/PAL auto select
SPECIFICATIONS
Note : This equipment has been testedand found to comply withthelimits for
a ClassAdigital device, pursuantto part 15 of the FCCRules.These limits
are designed to provide reasonableprotection against harmful interference
when the equipment is operatedin a commercial environment.
This equipment generates, uses, andcan radiate radio frequency energyand,
if not installed and usedin accordance with the instructionmanual, may cause
harmful interference to radio communications.Operation of this equipment in
a residential area is likelyto cause harmful interference inwhich case the user
will be required to correctthe interference at his ownexpense.
11.6(L)X8.7(W)X4.7(H)inches
2
CAUTION 4
INSTALLATION 5
NAME AND FUNCTION OF EACH PARTS 6
Unit 6
Remote Control 7
CONNECTIONS 8
HOW TO OPERATION THE MONITOR 9
How To Swivel The Monitor 9
How To Watch The Monitor 9
SPECIFICATIONS 10
Please read this User,s Manual in detail and use the set properly.
9
CONTENTSHOW TO OPERATE THE MONITOR
POWER
How to Swivel The Monitor
You can adjust the swivel angle as shown belown.
How to watch the monitor
UNIT
REMOTE CONTROLLER
1. Connect themonitor to theexternal devices.
2. Press thePOWER button oneither the remotecontrol or theunit once toturn
the power on.
Press the samePOWER button toturn the poweroff.
3.Turn on theexternal devices andview.
Make this arrow to swivel the monitor
AV2
M
3
8
CONNECTIONS
CAUTION
Please read andobserve all warningsand instructionsin this owners manual
and those markedon the unit.Retain thisbooklet for futurereference.
There are two kindsof alarmsymbols asfollows:
WARNING
WARNING
CAUTION
The lightening flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of
dangerous voltage within the product s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to
people.
The exclamationpoint within anequilateral triangle isintended
to alertthe user tothe presence ofimportant operating and
maintenance (servicing)instructions in theliterature accompanying
the product.
Installation of all TV monitors
must be out of the driver s
field of sight.
Do not try and service these
products yourself, Seek only
a qualified service center or
factory service center.
Be careful not to drop or
apply under pressure to the
front panel of your video
monitor. If the screen cracks
due to misuse, your warranty
will be void!
Do not mount the product where
it will obstruct the deployment of
the airbag or in an area where it
would affect the vehicular control.
Also be careful to avoid mounting
the product where it can become
hazardous during sudden stops or
in the event of an accident.
Be careful not to overload your
cigarette lighter plug by adding
more than one device at a time.
Use extra caution with any liquids
in your car.Ifyouor your child
Spills any liquid on these products,
pull your vehicle to the roadside
and turn the key off to disconnect
or wipe the products with a towel. Do not
operate the equipment until all liquids have
either evaporated or you have had the monitor
inspected at a service center by a qualified
technician, Severe harm or danger can
Occur.
Use only a damp cloth to clean
the screen and use only purified
water on the cloth. Wring out all
excess water prior to wiping the
screen. Do not use any cleaners
or chemicals to clean the screen.
In most cases a dry cloth will do!
P
O
W
E
R
A
V
MEN
U
,
,
AV2
M
Connect the wires as indicated:
a. Red: Connect toa switched(+) 12volt source (ACC).Use a leadthat has(+) 12V
when the ignitionon or intheACC position sothe monitors turnsoff when thekey is
in the off position. Wiringthe monitors hot could cause yourbattery to run down
when the engineis not running.
b. Black: Connectto a good chassisground.
c. Reversing thepolarity of thered and blackleads will damagethe monitor.
d. Connect thevideo input connectorto the videooutput from the sourceunit
(i.e. DVD player)
e.Test the syetem.
7
NAME AND FUNCTION OF EACH PART
Interface Switch Function
Power Power ON/OFF
AV Signal Select
Menu Press thisbutton for OSDmenu.
And selectmenu option
-
+
Increase currentoption value.
Decrease currentoption value.
LCD MONITOR
REMOTE CONTROL UNIT
POWER KEY
AV1/AV2 KEY
+KEY
-KEY
MENU KEY
CAUTION
4
Quality installations are best
performed by qualified and
certifled installers.
Don t touch the unitif there is
a flash of lightning. Itmay
receive an electric shock.
Do not cover heater ductsor vents.
This may cause a fireor an electric
shock.
Watchingthe monitor for an
extended period of time
with the engine turned off
may deplete the vehicle s
battery.
This product is designed for
operation with a 12 Volt DC,
negative ground vehicle. It
is not suitable for operation
under other conditions or
voltages.
1.The operating temperatureof this product is limitedto 14 F~140F
(-10 C~60 C).
Your vehicle canreach temperatures upto 100 Cin the summertime.
2. When yourvehicle is extremelyhot or coldyou must allowtime for yourair
conditioner or heaterto cool orheat the vehicleand for operatingtemperatures
to return tonormal operating ranges. Your monitor willreturn to itsnormal
functions when theseoperating ranges areachieved.
3. Optimum picturequality is achievedwhen you aredirectly in frontof the monitor
(+/-45 degrees).
4. If thebuttons get stuck,please try topress the upof buttons, itwill get back.
It won't impactusing normal.
5. If youcann't find thefiles name inlist when playing,please reset unitsor turn
off/onover again.
6. If theunit cann't bechange mode whenplaying some specialfiles which the
unit didn't support,please reset unitsor turn off/onover again.
CAUTION
Check Point
Remote Control
6
INSTALLATION NAME AND FUNCTION OF EACH PART
Unit
Product installed
AV2
M
1. Remove theexisting headrest fromthe seat.
2.Adjust the postsof the newheadrest to fitthe holes inthe seat wherethe
headrest will beinstalled.The post can be movedtogether or apart
grasp one postin each hand,move the postsin opposing directions
(like they werewalking) while pushingthem toward eachother or away
from each other.
3. Insert thecable in theproper hole. Insertthe posts intothe holes inthe
seat and carefullywork the headrestinto position. Makesure the cable
is not pinched.
4. Run thecable down theseat and outto the locationof the video source
unit (such asa DVD player).
5. See thepicture on theright and youcan adjust
the distance betweenthe tubes torequired
space(pole width adjustments4 ~ 8.2 .
)
AV2
M
5
AV2
M
HEADPHONE JACK
Headphone output
Adjustable steel Pipe
PIPE
AV2 Inputs
1 2 34567
88
How to use the Adapter tubes
Since the spacingof the mountingholes
can vary ondifferentveicles we supply
two adapter tubes.Use these tubeswhen
the headrest mountingholes in yourseat
are too largefor the postsof the headrest
monitor.
And IR TRANSMITTER
Loading...