Power Acoustik
FUBAR
Woofers
Congratulations on your purchase of one of the finest woofers available for your vehicle today.
If you are an enthusiast that plays your system loud and hard, the FUBAR woofers'will take you to
limit. Our small sealed enclosure, high excursion design will move enough air to part your hair. Let
your woofers do all the talking to let everyone know you are a "Serious about your sound".
Please take a few moments to fill out the warranty card and review this manual before installing this
woofer for proper connections and box sizes.
Design Features
Die cast aluminum basket
Candy Blue finish
Non-pressed laminated paper cone
Chrome back plate
Large foam surround
1-piece rubber gasket
Black poly-cotton spider
Woven tinsel leads through the spider
Chrome push
Dual 4-ohm voice coil
SPL: 90 dB 91 dB 93
Magnet size: 160oz. 20002. 25002.
BASV voice coil: 2" 2" 2.5"
(RMS
Power
Power (MAX watts): 1,600 1,800 2,000
w/ Diamond cut
terminals
FUBAR-10W FUBAR-12W FUBAR-15W
dB
watts): 600 800 1,000
--
\a-'
Thiele / Small Parameters
FUBAR-1OW FUBAR-12W FUBAR-1SW
Fs 36.8
Va s 0.99 Cu. Ft.
Qms
Qes 0.510
Qts 0.462
X-max I0 mm 10 mm 13 mm
4.866
Hz
36 Hz 27.2 Hz
1 Cu. Ft. 4.5 Cu.Ft.
1.9
1
5.73
0.502 0.496
0.462 0.463
6.291
Recommended box
sizes
I
\L/
Model
FUBAR-1OW
FUBAR-12W
1
FUBAR-15W I 2.25
Sealed
0.75
1.2
cubic feet
Box
Size
cubic feet
cubic feet
Ported
1.5
2.0
I
3.4
Box
Size
cubic feet
cubic feet
cubic feet
Tune Freq.
40
Hz
40
Hz
I
39
Hz
#
of Ports
1
.
Port (dia x length)
1
1
2
1
4"
4"
3"
x
x
x
6.5"
8.75
7.25"
Building the Enclosure
Determine the dimensions of your enclosure.
Be certain the box dimensions that you have designed will fit in the location you
have chosen in your vehicle. Sometimes making a cardboard box with the same
outside dimensions is helpful.
%
It is recommended to use
"T"
Use a
square to verify precise right angle cuts before you assemble the box.
Use high quality wood glue and screws to assemble the box to guarantee an airtight box
that will not come apart due to excess vibration and pressure.
It is recommended for sealed enclosures to stuff the interior of the box about
fiberglass insulation or Dacron fiberfill for increased sound damping and woofer performance.
For ported enclosures, it is recommended to staple
interior walls of your box.
Use slide on connectors for spade style connectors or bare wire for push and screw
terminals. Do not solder the wires to the factory connectors as this may cause damage to the
voice coil or tinsel lead and may void your warranty.
inch thick MDF (medium density fiberboard) for your box.
50
-
75%
1"
thick fiberglass insulation to the
1
Recommended wiring
The
'L
following page will give you a few different options to match the impedance of the
woofers to the impedance capability of the amplifier. Please look and follow the diagrams
closely to insure maximum woofer
performance.
Parallel voice coil configuration
I-ohm Load
Series voice coil configuration
I
I
4-ohm 4-ohm
SeriesIParallel voice coil configuration
1
4-ohm 4-ohm Amplifier
4-ohm Load
Amplifier
8-ohm Load
Loading...