Power Acoustik BAMF2200/2, BAMF1250/2, BAMF2600/2, BAMF1600/4, BAMF4000/1D Owner's Manual
...
*************
OWNER'S MANUAL
BAMF800/2 BAMF1250/2 BAMF1800/2 BAMF2200/2
BAMF2600/2 BAMF1200/4 BAMF1600/4
BAMF2000/1D BAMF4000/1D BAMF5500/1D
- 2 -
INTRODUCTION
Power Acoustik amplifiers provide high-performance sound reinforcement for your
mobile audio equipment. Its versatility enables compatibility with optional Equalizers,
Frequency Dividing Crossover Networks, and other audio processors in a customized
system. The Multi-Mode bridging capabilities allow flexibility in hosting several different
speaker configurations.
To achieve optimum performance, it is highly recommended that you read this
Owners Manual before beginning installation.
WARNING
High powered audio systems in a vehicle are capable of generating "Live Concert"
high levels of sound pressure. Continued exposure to excessively high volume sound
levels may cause hearing loss or damage. Also, operation of a motor vehicle while
listening to audio equipment at high volume levels may impair your ability to hear
external sounds such as; horns, warning signals, or emergency vehicles, thus
contributing to a potential traffic hazard. In the interest of safety, Power Acoustik
recommends listening at lower volume levels while driving.
- 3 -
Before beginning the installation, consider the following:
1. Do you plan to add additional mobile electronics equipment in the future?
If you plan to expand your system by adding other components sometime in the
future, ensure adequate space is left and cooling requirements are met.
2. Should you use high or low level inputs?
Your Amplifier has been designed to accept Low-Level(Pre-Amp outputs from your
radio) source signal. If your radio/source is equipped with Pre-Amp outputs, it is
possible to utilize them to drive the Amplifier and the 2 front speakers. Then, use the
built-in power of your radio to drive the 2 rear speakers.
3. Are your components matched?
The RMS power rating of your speaker(s) must be equal or greater than the RMS
power rating of your amplifier. Your speaker(s) also must be 2 - 8 Ohms impedance
for stable amplifier operation. Impedance information is normally printed on the
speaker basket or magnet.
4. Where will the amplifier be installed?
Consider both the length of your leads, and routing when determining the mounting
location. It is best to run power and RCA wiring on opposite sides of the vehicle to
prevent induced noise. Pre-amp input jacks require a length of high quality shielded
male to male RCA patch cord.
PLANNING YOUR SYSTEM ................................................................
WIRING CONNECTION ....................................................................
PANEL LAYOUT .................................................................................
CONTROL FUNCTIONS .....................................................................
SPEAKER CONNECTION MONO CHANNEL ...................................
2 CHANNEL ............................................
4 CHANNEL ............................................
TROUBLE SHOOTING GUIDE ............................................................
SPECIFICATION .................................................................................
WARNING .........................................................................................
3
4, 5
6, 7
8-10
11-14
15, 16
17-19
20
21
22
TABLE OF CONTENTS
PLANNING YOUR SYSTEM
- 4 -
CONNECTING THE POWER (Fig.1,2)
CAUTION:
AS A PRECAUTION, DISCONNECT THE POWER WIRE FROM THE BATTERY WHILE MAKING THE
POWER AND GROUND CONNECTIONS TO THE AMPLIFIER.
4/8 GAUGE(Thicker if planning for additional Amplifiers) wire is recommended for
both the power and ground wires. 12 Gauge, for the remote turn-on wire. Both
types are available at most Mobile Audio Dealers or Installation Shop.
(1) Ground : To Vehicle Chassis
To avoid unwanted ignition noise caused by ground loop, it is essential that the
Amplifier be grounded to a clean, bare, metal surface of the vehicle's Chassis
NOTE :
GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT. (1 METER).
(2) +12 Volt(Fused) Constant Power: To Battery (+)
Due to the power requirements of the Amplifier, this connection should be made
directly to the positive (+) terminal of battery. For safety measures, install an in-line
Fuse Holder (not included) as close to the battery positive (+) terminal as
possible with an ampere rating; not to exceed total value of fuses in Amp.
(3)
Remote Turn-On Input: To remote turn-on output of Car Stereo
This Amplifier is turned "ON" remotely when the vehicle's stereo is turned "ON".
NOTE :
IF YOUR RADIO DOES NOT HAVE A +12 VOLT OUTPUT LEAD WHEN THE RADIO IS TURNED ON, THE "REMOTE"
TERMINAL ON THE AMPLIFIER CAN BE CONNECTED TO VEHICLE'S ACCESSORY CIRCUIT THAT IS LIVE WHEN THE
KEY IS "ON".
- 5 -
- 6 -
PANEL LAYOUT
- 7 -
PANEL LAYOUT
- 8 -
CONTROL FUNCTIONS
1. RCA input jacks
These RCA input jacks are for use with source units that have RCA or Line level
outputs. A source unit with a minimum level of 200mV is required for proper operation.
The use of high quality twisted pair cables is recommended to decrease the possibility
of radiated noise entering the system.
2. GAIN Control
The level control will match the amplifiers sensitivity to the source units signal voltage.
The Operating range is 200mV minimum to 6V maximum.
CAUTION: Do not run the amplifier in high volume for long time, otherwise the loudspeakers will be
damaged.
3. Full pass x-over switch
When the switch is in the "Full" position, the full range is bypassed.
4. Low pass x-over switch
When the switch is in the "LPF" position, frequencies lower than the low pass frequency
setting are passed.
4.1 Low pass x-over frequency control
This control is used to select the desired low pass x-over frequency.
BAMF800/2, 1250/2, 1800/2, 2200/2, 2600/2, 1200/4, 1600/4 : The frequency can be
adjusted between 30Hz and 250Hz.
BAMF2000/1D, 4000/1D, 55001D : The frequency can be adjusted between 40Hz and
200Hz.
5. High pass x-over switch
When the switch is in the "HPF" position, frequencies higher than the high pass
frequency setting are passed.
5.1 High pass x-over frequency control
This control is used to select the desired high pass x-over frequency.
BAMF800/2, 1250/2, 1800/2, 2200/2, 2600/2, 1200/4, 1600/4 : The frequency can be
adjusted between 50Hz and 500Hz.
6.Bass EQ
BAMF800/2, 1250/2, 1800/2, 2200/2, 2600/2, 1200/4, 1600/4 : The boost can be
adjusted between 0dB to12dB.
BAMF2000/1D, 4000/1D, 55001D : The boost can be adjusted between 0dB to 18dB.
7. Auxiliary outputs
The Auxiliary outputs offer Power Acoustik amplifiers easy, unlimited system expansion.
Route RCA's from the line out of the first amplifier to the line input of a second
amplifier when using a single source output.
- 9 -
CONTROL FUNCTIONS
8. SUBSONIC
BAMF1250/2, 1800/2, 22200/2, 2600/2 : The frequency can be adjusted between 15Hz
and 50Hz.
BAMF2000/1D, 4000/1D, 5500/1D : The frequency can be adjusted between 20Hz and
50Hz.
9. REMOTE
Controls the subwoofer amplifier gain, from a remote location for ease of adjustment
during listening.
Warning: Do not connect a level control knob from other manufacturers to the Remote Sub Level
Control of any amplifier. Even though the connectors fit properly, the control knob and connector
pin positions may be different and the amplifier will be damaged.
10. PHASE
0°or180° selectable for switching the phase of the output to the woofer.
11. MASTER/SLAVE MODE[BAMF2000/1D, 4000/1D, 5500/1D]
Controls whether the amplifier is a slave or master when connected in combined
amplifier configurations. (Refer to the Master Mode section of this guide.)
All of the controls will be adjusted by the "Master" amplifier.
-Slave mode : To be switched " Slave mode" when linking one amplifier with another
amplifier.
-Master mode : To be switched " Master mode" when only using this single amplifier.
12. INPUT MODE
Selects 2, 3 or 4 channel operation(FIG. 1)
13. GND
Connect this terminal directly to the sheet metal chassis of the vehicle, using the
shortest wire necessary to make this connection. Always use wire of the same gauge
or larger than the (+)12 volt power wire. The chassis connection point should be
scraped free of paint and dirt. Use only quality crimped and/or soldered connectors
at both ends of this wire.
Warning : Do not connect this terminal directly to the vehicle battery ground terminal or any other
factory ground points.
14. Remote Turn On
This terminal turns on the amplifier when (+)12 volt is applied to it. Connect it to the
remote turn on lead of the head unit or signal source.
15. (+)12 Volt Power
Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of
the vehicle battery or the positive terminal of an isolated audio system battery.
Warning: Always protect this power wire by installing a fuse or circuit breaker of the appropriate
size within 12 inches of the battery terminal connection.
FIG. 1
CONTROL FUNCTIONS
16. FUSE
These fuses protect the amplifier against internal electrical damage and are meant to
protect the amplifier only. All other power connections should be fused at the source.
BAMF800/2 : 25A X 1 BAMF1250/2 : 20A X 2 BAMF1800/2 : 20A X 3
BAMF2200/2 : 20A X 4 BAMF2600/2 : 25A X 4
BAMF1200/4 : 25A X 2 BAMF1600/4 : 25A X 2
BAMF2000/1D : 40A X 2 BAMF4000/1D : 40A X 3 BAMF5500/1D : 40A X 5
17. SPEAKERS
Connect subwoofers to these terminals.
18. LED
Will illuminate GREEN to indicate the amplifier is on and operating normally, and will
be illuminated RED if the amplifier shuts down due to short circuit, DC offset, or
overheating detected by on board protection circuitry
- 10 -
- 11 -
FIG. 2 MASTER MODE CONFIGURATION
BAMF 2000/1D, BAMF 4000/1D
1.Lowest Recommended Impedance is 1ohm mono.
2.RCA Inputs are connected to both Left and Right channels
3.Gain controls to be set match input source
4.Line Output configured for stereo operation
FIG. 3 STRAPPED CONFIGURATION
BAMF 2000/1D, BAMF 4000/1D
2-4ohms
STRAPPED CONFIGURATION
- 12 -
1.Lowest Recommended Impedance is 2ohm Stereo
2.RCA Inputs are connected to both Left and Right channels
3.Gain controls to be set match input source
4.Line Output is configured summed bridged which is ideal for subwoofer applications
- 13 -
FIG. 4 MASTER MODE CONFIGURATION
BAMF5500/1D
1. Lowest recommended impedance is 1 Ohm Mono.
2. RCA Inputs are connected to both left and right cnannels.
3. Gain control is to be set to match input source.
- 14 -
2-4ohms
STRAPPED CONFIGURATION
FIG. 5 SLAVE MODE CONFIGURATION
BAMF5500/1D
1. All of the controls can be adjusted only in "MASTER" mode amplifier.
2. Lowest recommended impedance is 2 Ohm Mono.
3. RCA Inputs are connected to both left and right cnannels.
4. Gain control is to be set to match input source.
- 15 -
FIG. 4 2 CHANNEL STEREO CONFIGURATION
BAMF 800/2, 1250/2, 1800/2, 2200/2, 2600/2
FIG. 5 2CHANNEL BRIDGED CONFIGURATION
BAMF 800/2, 1250/2, 1800/2, 2200/2, 2600/2
1.Lowest Recommended Impedance is 2ohm Stereo
2.RCA Inputs are connected to both Left and Right channels
3.Gain controls to be set match input source
4.Line Output configured for stereo operation
1.Lowest recommended impedance is 4ohm bridged mono
2.RCA Inputs are connected to both Left &Right channels
3.Line Output configured for stereo operation
- 16 -
FIG. 6 2CHANNEL TRI MODE CONFIGURATION
BAMF 800/2, 1250/2, 1800/2, 2200/2, 2600/2
1.Lowest Recommended Impedance is 4ohm Stereo
2.RCA Inputs are connected to both Left and Right channels
3.Output configured for stereo operation
- 17 -
FIG. 7 4CHANNEL STEREO CONFIGURATION
BAMF 1200/4, BAMF 1600/4
1.Lowest Recommended Impedance is 2ohm Stereo
2.RCA Inputs are connected to both Left and Right channels
3.Gain controls to be set match input source
4.Line Output configured for stereo operation
- 18 -
FIG. 8 4CHANNEL BRIDGED CONFIGURATION
BAMF 1200/4, BAMF 1600/4
1.Lowest recommended impedance is 4ohm bridged mono
2.RCA Inputs are connected to both Left &Right channels
3.Line Output configured forstereo operation
- 19 -
FIG. 9 4CHANNEL TRI MODE CONFIGURATION
BAMF 1200/4, BAMF 1600/4
1CH
4-8 Ohms
WOOFER
2CH
4-8 Ohms
3CH
4-8 Ohms
4CH
4-8 Ohms
WOOFER
1.Lowest Recommended Impedance is 4ohm Stereo
2.RCA Inputs are connected to both Left and Right channels
3.Output configured for stereo operation
- 20 -
TROUBLE SHOOTING GUIDE
Check fuses in amplifier.
Be sure Turn-on lead is connected
Repair power wire or connections
Check connections to radio
Check fuse
Inspect for short circuit or an
open connection.
Reverse Left and Right
RCA inputs to determine if it is
occurring before the amp.
Check Tuner/Deck volume level.
Clean contacts on fuse holders.
Be sure proper speakers are used
to ensure impedance
recommendations are observed.
(If you use an Ohmmeter to
check speaker resistance,
please remember that DC
resistance and AC impedance
may not be the same.)
NO SOUND
AMP NOT
SWITCHING
ON
NO SOUND
IN ONE
CHANNEL
AMP
TURNING
OFF
MEDIUM/
HIGH
VOLUME
SYMPTOMS CHECK POINTS CURE
Is the power
LED illuminated?
No power to power wire
No power to remote
wire with receiver on
Fuse broken
Check speaker leads
Check audio input
leads
Check speaker load
impedance
- 21 -
MODEL#
MAXIMUM POWER
OUTPUT
POWER OUTPUT
@4Ohm
POWER OUTPUT
@2Ohm
BRIDGED POWER
THD
FREQUENCY
RESPONSE -1.0dB
HPF
LPF
SUBSONIC FILTER
BASS EQ
ADJUST ABLE
SENSITIVITY RANGE
INPUT IMPEDANCE
(LOW LEVEL)
FUSE
DIMENSION
(D x W x H inch)
BAMF800/2
800W
150W x 2CH
180W x 2CH
360W x 1CH
0.02%
10Hz-30kHz
50Hz~500Hz
30Hz~250Hz
-
0dB ~ 12dB
0.2V~6V
10k Ohms
25A x 1
18.7" x
8.26" x 2.16"
BAMF-1250/2
1250W
220W x 2CH
280W x 2CH
560W x 1CH
0.02%
10Hz-30kHz
50Hz~500Hz
30Hz~250Hz
15Hz~50Hz
0dB ~ 12dB
0.2V~6V
10k Ohms
20A x 2
11.37" x
8.26" x 2.16"
BAMF1800/2
1800W
300W x 2CH
380W x 2CH
760W x 1CH
0.02%
10Hz-30kHz
50Hz~500Hz
30Hz~250Hz
15Hz~50Hz
0dB ~ 12dB
0.2V~6V
10k Ohms
20A x 3
13.77" x
8.26" x 2.16"
BAMF2200/2
2200W
370W x 2CH
450W x 2CH
900W x 1CH
0.02%
10Hz-30kHz
50Hz~500Hz
30Hz~250Hz
15Hz~50Hz
0dB ~ 12dB
0.2V~6V
10k Ohms
20A x 4
14.96" x
8.26" x 2.16"
BAMF2600/2
2600W
450W x 2CH
540W x 2CH
1080W x 1CH
0.02%
10Hz-30kHz
50Hz~500Hz
30Hz~250Hz
15Hz~50Hz
0dB ~ 12dB
0.2V~6V
10k Ohms
25A x 4
16.92" x
8.26" x 2.16"
MODEL#
MAXIMUM POWER
OUTPUT
POWER OUTPUT
@4Ohm
POWER OUTPUT
@2Ohm
POWER OUTPUT
@1Ohm
BRIDGED POWER
THD
FREQUENCY
RESPONSE -1.0dB
HPF
LPF
SUBSONIC FILTER
BASS BOOST
ADJUST ABLE
SENSITIVITY RANGE
INPUT IMPEDANCE
(LOW LEVEL)
FUSE
DIMENSION
(D x W x H inch)
BAMF1200/4
1200W
100W x 4CH
125W x 4CH
-
250W x 2CH
0.02%
10Hz-30kHz
50Hz~500Hz
30Hz~250Hz
-
0dB ~ 12dB
0.2V~6V
10k Ohms
25A x 2
13.77" x
8.26" x 2.16"
BAMF1600/4
1600W
150W x 4CH
180W x 4CH
-
360W x 2CH
0.02%
10Hz-30kHz
50Hz~500Hz
30Hz~250Hz
-
0dB ~ 12dB
0.2V~6V
10k Ohms
25A x 2
13.77" x
8.26" x 2.16"
BAMF2000/1D
2000W
600W x 1CH
900W x 1CH
1200W x 1CH
-
0.2%
(-3dB)
20Hz-200Hz
-
40Hz~200Hz
20Hz~50Hz
0dB ~ 18dB
0.2V~6V
10k Ohms
40A x 2
11.37" x
8.26" x 2.16"
BAMF4000/1D
4000W
1200W x 1CH
1700W x 1CH
2200W x 1CH
-
0.2%
(-3dB)
20Hz-200Hz
-
40Hz~200Hz
20Hz~50Hz
0dB ~ 18dB
0.2V~6V
10k Ohms
40A x 3
13.77" x
8.26" x 2.16"
BAMF5500/1D
5500W
1700W x 1CH
2500W x 1CH
3200W x 1CH
-
0.2%
(-3dB)
20Hz-200Hz
-
40Hz~200Hz
20Hz~50Hz
0dB ~ 18dB
0.2V~6V
10k Ohms
40A x 5
16.92" x
8.26" x 2.16"
SPECIFICATIONS
- 22 -
WARNINGS
Investigate the layout of your automobile throughly before drilling or cutting
any holes. Take care when to work near the gas tanks, lines, or hydraulic
lines, and electrical wiring. Don't use power amplifier unmounted. Attach
this system securely to the automobile to prevent damage, particularly in
the event of an accident. Don't mount this system so that the wire
connections are unprotected or are subject to pinching or damage from
nearby objects. The +12V DC power wire must be fused at the battery
positive terminal connection. Before making or breaking power connections
at this system power terminals, disconnect the +12V wire at the battery end.
Confirm your radio/cassette player and/or other equip is turned off while
connecting the input jacks and speaker terminals. If you need to replace
the power fuse, replace it only with a fuse identical to that supplied with the
system. Using a fuse of different type or rating may result in damage to this
system which isn't covered by the warranty.
Loading...