Poulan 917279870 Owner’s Manual

IMPORTANT MANUAL Do Not Throw Away

OWNE R'S MANUAL

MODEL:

Read this Owner's Manual and follow all Warnings and Safety

Instructions. Failure to do so can result in serious injury.

PR1842STA

LAWN TRACTOR

Always Wear Eye Protection During Operation

WARNING:

181347 1.22.02 RD

Printed in U.S.A.

Safe Operation Practices for Ride-On Mowers

IMPORTANT: THIS CUTTING MACHINE ISCAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS.

FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

SAFETY RULES

I. GENERAL OPERATION

• Read,understand, and follow allinstructions inthe manual and on the machine before starting.

• Only allow responsible adults, who are familiar with the

instructions, to operate the machine.

• Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade.

• Besure the area is clear of other people before mowing.

Stop machine ifanyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.

• Beaware ofthemower discharge direction and do notpoint

itat anyone. Do not operate the mower without either the

entire grass catcher or the guard in place.

• Slow down before turning.

• Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove

keys before dismounting.

• Turn off blades when not mowing.

• Stop engine before removing grass catcher or unclogging chute.

• Mow only in daylight or good artificial light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Watch for traffic when operating near or crossing road- ways.

• Useextracarewhen loading orunloading the machine into a trailer or truck.

• Dataindicates that operators, age 60 years and above, are

involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to

operate the riding mower safely enough to protect them- selves and others from serious injury.

• Keep machine free ofgrass, leaves or other debris build-

up which can touch hot exhaust/engine parts and burn. Do not allow the mower deck to plow leaves

or other debris which can cause build-up to occur. Clean any oil or fuel spillage before operating or storing the

machine. Allow machine to cool before

storage.

II. SLOPE OPERATION

Slopes are a major factor related to loss-of-control and tipover

accidents, which can result in severe injury or death. All slopes

requireextra caution. Ifyou cannot backup theslopeor ifyoufeel uneasyon it, do not mow it.

DO:

• Mow up and down slopes, not across.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

• Use slow speed. Choose a low gear so that you will not

have to stop or shift while on the slope.

• Follow the manufacturer's recommendations for wheel weights or counterweights to improve stability.

• Useextra care with grass catchers or other attachments. These can change the stability of the machine.

• Keep all movement on the slopes slowand gradual Do

not make sudden changes in speed or direction.

• Avoid starting or stopping on a slope. Iftires lose traction, disengage the blades and proceed slowly straight down the slope.

DO NOT:

• Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.

• Do not mow near drop-offs, ditches, or embankments. The mower could suddenly turn over if awheel is overthe

edge of a cliff or ditch, or if an edge caves in.

• Do notmow on wet grass. Reduced traction could cause sliding.

• Do not try to stabilize the machine by putting your foot on theground.

• Do not use grass catcher on steep slopes.

III. CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the machine and the mowing activity. Neverassumethat children

will remain where you last saw them.

• Keep children out of the mowing area and under the watchful care of another responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and when backing, look behind and downforsmall children.

• Never carry children. They may fall off and be seriously

injured or interfere with safe machine operation.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

IV. SERVICE

• Useextra care inhandlinggasolineand otherfuels. They are flammable and vaporsare explosive.

- Useonlyanapproved container.

- Never remove gas cap or add fuel with the engine

running. Allowengine to cool before refueling. Do not

smoke.

- Never refuel the machine indoors.

- Never store the machine or fuel container inside where

there is an open flame, such as a water heater.

• Never run a machine inside a closed area.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free ofgrass, leaves, orother debris build-

up. Clean oilor fuel spillage. Allow machineto cool before

storing.

• Stop and inspect the equipment if you strike an object.

Repair, ifnecessary, before restarting.

• Never make adjustments or repairs with the engine

running.

• Grasscatcher components aresubject towear, damage, and deterioration, which could expose moving parts or

allow objects to bethrown. Frequently check components and replace with manufacturer's recommended parts,

when necessary.

• Mower blades are sharp and can cut. Wrapthe blade(s) or wear gloves, and use extra caution when servicing them.

• Check brake operation frequently. Adjust and service

as required.

SAFETY RULES

& Safe Operation Practices for Ride-On Mowers &

• Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area.

• Never carry passengers or children even with the blades

off.

• Do not mow in reverse unless absolutely necessary. Al-

ways look down and behind before and while backing.

• Never carry children. They may fall off and be seriously injured or interfere with safe machine operation.

• Keep children out of the mowing area and under the

watchful care of another responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and when backing, look behind and down for small

children.

• Mow up and down slopes (15° Max), not across.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Uneven terrain could

overturn the machine. Tall grass can hide obstacles.

• Use slow speed. Choose a low gear so that you will not have

to stop or shift while on the slope.

• Avoid starting or stopping on a slope. If tires lose traction,

disengage the blades and proceed slowly straight down the slope.

• If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.

• Do not turn on slopes unless necessary, and then, turn

slowly and gradually downhill, if possible.

Look for this symbol to point out im- portant safety precautions. It means

CAUTION!!! BECOMEALERT!!! YOUR SAFETY IS INVOLVED.

CAUTION: In order to prevent acciden-

tal starting when setting up, transport-

ing, adjusting or making repairs, al- ways disconnect spark plug wire and

place wire where itcannot contact spark plug.

CAUTION: Do not coast down a hill in neutral, you may lose control of the

tractor.

CAUTION: Tow only the attachments

that are recommended by and comply

with specifications ofthe manufacturer of your tractor. Use common sense when towing. Operate only at the low- est possible speed when on a slope.

Too heavy of a load, while on a slope,

is dangerous. Tires can lose traction with the ground and cause you to lose

control of your tractor.

TABLE OF CONTENTS

SAFETY RULES ...................................................... 2 - 3

PRODUCT SPECIFICATIONS ....................................... 4

CUSTOMER RESPONSIBILITIES ................... 4, 15- 18

ASSEMBLY .............................................................. 6 - 8

OPERATION ........................................................... 9 - 14

MAINTENANCE SCHEDULE ....................................... 15

WARNING

Engine exhaust, some of its constituents, and cer-

tain vehicle components contain or emit chemicals

known to the State of California to cause cancer and

birth defects or other reproductive harm.

WARNING

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known

to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

SERVICE AND ADJUSTMENTS .......................... 19 - 23

STORAGE ................................................................... 24

TROUBLESHOOTING .......................................... 25 - 26

REPAIR PARTS ................................................... 28 - 43

WARRANTY ................................................................ 45

PRODUCT SPECIFICATIONS

GASOLINE CAPACITY 2.00 GALLONS AND TYPE: UNLEADED REGULAR

OILTYPE (API-SF-SJ): SAE 30 (above 32°F)

SAE 5W-30 (below 32°F)

OIL CAPACITY: W/FILTER: 3.5

W/O FILTER: 3.0

SPARK PLUG: CHAMPION RC12YC (GAP: .030")

GROUND SPEED (MPH): FORWARD:

1st 1.2

2nd 1.5 3rd 2.4

4th 3.5 5th 4.8

6th 5.3

REVERSE: 1.5

TIRE PRESSURE: FRONT: 14 PSI

REAR: 10 PSI

CHARGING SYSTEM: 3 AMPS BATTERY

5 AMPS HEADLIGHTS

BATTERY: AMP/HR: 28

MIN. CCA: 230

CASE SIZE: UIR

BLADE BOLT TORQUE: 27-35 FT. LBS.

CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give

you the best possible dependability and performance. Should you experience any problem you cannot easily

remedy, please contact your nearest authorized service centre/department. We have competent, well-trained tech-

nicians and the proper tools to service or repair this tractor. Please read and retain this manual. The instructions will

enable you to assemble and maintain your tractor properly. Always observe the "SAFETY RULES".

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for and using your tractor.

• Follow the instructions under "Customer Responsibili- ties" and "Storage" sections of this owner's manual.

WARNING: This tractor is equipped with an internal com- bustion engine and should not be used on or near any

unimproved forest-covered, brush-covered or grass-cov- ered land unless the engine's exhaust system is equipped

with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained

in effective working order by the operator. A spark arrester for the muffler is available through your

nearest authorized service centre/department (See RE- PAIR PARTS section of this manual).

CONTENTS OF HARDWARE PACK

Steering Wheel

_- Steering

Extension Shaft

_/1 Steering 3/8-16 x 1

/Wheel Insert _ering

(1) Large Flat

Washer

O __ (1) Hex Bolt

Sleeve

(1) Lock

washer 3/8

Seat

(1) Washer @ 17/32 x 1-3/16 x 12 Gauge

(1) Knob

For Future Use

Keys

Slope Sheet

(1) Hex Bolt 5/16-18 x 1-1/4

(1) Locknut

5/16-18

Steering

Wheel Adapter

ASSEMBLY

Your new tractor has been assembled atthe factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the

correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2) 1/2" wrenches Utility knife (2) 9/16" wrench Tire pressure gauge

Pliers When right or left hand is mentioned in this manual, itmeans

when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

• Remove all accessible loose parts and parts cartons

from carton.

• Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

• Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

• Slideextension shaftontolowersteering shaft. Align mount-

ing holes in extension and lower shafts and install 5/16 hex bolt and Iocknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 18-22 FT. LBS TORQUE.

• Placetabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

• Position front wheels of the tractor so they are pointing straight forward.

• Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

• Positionsteering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

• Assemblelargeflatwasher,3/8 lockwasher,3/8hexboltand tighten securely.

• Snap steering wheel insert into center of steering wheel.

• Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKI D THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

ADAPTER

5/16 LOCKNUT------_"_'f SHAFT

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

• Liftseat pan to raised position.

• If this battery is put into service after month and year

indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps.

(See "BATTERY" inCUSTOMER RESPONSIBILITIES section of this manual for charging instructions).

SEAT PAN

_ INSERT

3/8 HEX BOLT 3/8 LOCK WASHER

LARGE FLAT WASHER

_ EXTENSION

_:_ 5/16 HEX

4 - _ BOLT

FIG. 1

LABEL

FIG. 2

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

• Remove adjustment knob and flat washer securing seat tocardboard packing and set aside for assembly of seat

to tractor.

• Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

• Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

• Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

• Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

• Lower seat into operating position and sit on seat.

• Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

• Get off seat without moving its adjusted position.

• Raise seat and tighten adjustment knob securely.

_EAT

SEAT P_

FLAT WASHER

SHOULDER BOLT

TO ROLL TRACTOR OFF SKID (See Opera- tion section, page 10, for location and

function of controls)

• Press lift lever plunger and raise attachment lift lever to its highest position.

• Release parking brake bydepressing clutch/brake pedal.

• Place gearshift lever in neutral (N) position.

• Roll tractor forward off skid.

• Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Opera- tion section, page 10, for location and func-

tion of controls)

WARNING: Beforestarting, read, understand and follow

all instructions inthe Operation section of this manual. Be

sure tractor is ina well-ventilated area. Be sure the area in front of tractor isclear of other people and objects.

• Be sure all the above assembly steps have been

completed.

• Check engine oil level and fill fuel tank with gasoline.

• Sit on seat inoperating position,depress clutch/brake pedal and set the parking brake.

• Place gear shift lever in neutral (N) position.

• Press liftlever plunger and raise attachment liftlever to

its highest position.

• Start the engine. After engine has started, movethrottle controlto idle position.

• Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

• Slowly release clutch/brake pedal and slowly drive tractor off skid.

• Apply brake to stop tractor, set parkingbrake and place gearshift lever in neutral position.

• Turn ignition key to "OFF" position.

Continue with the instructions that follow.

ADJUSTMENT

KNOB

FIG. 3

NOTE: You may now roll or drive your tractor off the skid.

Follow the appropriate instruction below to remove the tractor from the skid.

ASSEMBLY

IMPORTANT: FOR SHIPPING PURPOSES, THE

MULCHER PLATE WAS PREATTACHED TO YOUR MOWER. THE MULCHER PLATE MUST ONLY BE USED WITH THE MULCHING BLADES THAT CAME PACKED SEPARATELY IN THE CARTON.

YOUR MOWER CAME FACTORY EQUIPPED WITH HIGH PERFORMANCE BLADES, WHICH ARE THE BEST

BLADES FOR BAGGING AND DISCHARGING. TO USE YOUR MOWER WITH THE HIGH PERFORMANCE BLADES THE MULCHER PLATE MUST BE REMOVED FROM THE

MOWER (SEE FIG. 4).

TO SET UP YOUR MOWER FOR MULCHING

• Remove high performance blades and install mulcher blades, (see BLADE REMOVAL in the CUSTOMER

RESPONSABILITY section of this manual).

TO INSTALL MULCHER PLATE (See Fig. 4)

NOTE: If you installed the mulching blades you will need to installthe mulcher plate.

• Raise and holddeflector shield in upright position.

• Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

• Hook front latch into hole on front of mower deck.

• Hook rear latch into hole on back of mower deck.

CAUTION: Donot remove deflector shield

from mower. Raise and hold shield when attaching mulcher plate and allow it to

rest on plate while in operation.

DEFLECTOR SHIELD

FIG. 4

MULCHER PLATE

LATCH HOOKS

TO CONVERT TO BAGGING OR DISCHARG- ING

NOTE: The mulcher blades will discharge and bag grass, but

forbest bagging and discharging install the high performance blades.

• Remove mulcher plate and mulcher blades and install high performance blades, (see BLADE REMOVAL inthe

CUSTOMER RESPONSABILITY section ofthis manual).

• Store mulcher blades and mulcher plate in a safe place. Your mower is now ready for discharging or installation

of optional grass catcher accessory.

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for

best cutting performance.

• Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower housingshould be properly leveled. See"TO LEVEL MOWER HOUSING"in theService

and Adjustments section ofthis manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments

section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, checkto see that the brake is properly adjusted. See "TO ADJUST BRAKE"

in the Service and Adjustments section of this manual.

,/CHECKLIST

BEFORE YOU OPERA TEAND ENJOY YOURNEW TRAC-

TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE

BEST PERFORMANCE AND SATISFACTION FROM THIS

QUALITYPRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST:

,/ All assembly instructions have been completed. ,/ No remaining loose parts in carton. ,/ Batteryis properly prepared and charged. (Minimum 1

hour at 6 amps).

,/ Seat is adjusted comfortably and tightened securely. ,/ All tires are properly inflated. (For shipping purposes,

the tires were overinflated at the factory).

,/ Be sure mower deck is properly leveled side-to-side/

front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

,/ Check mower and drive belts. Be sure they are routed

properly around pulleys and inside all belt keepers.

,/ Check wiring. See that all connections are still secure

and wires are properly clamped.

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

,/ Engine oil is at proper level. ,/ Fuel tank is filled with fresh, clean, regular unleaded

gasoline.

,/ Become familiar with all controls - their location and

function. Operate them before you start the engine.

,/ Be sure brake system is in safe operating condition.

OPERATION

These symbols may appear on yourtractor or in literature supplied withthe product. Learn and understand their meaning.

BATTERY CAUTION OR REVERSE FORWARD FAST SLOW

WARNING

ENGINE ON ENGINE OFF OIL PRESSURE LIGHTS ON OVER TEMP

LIGHT

FUEL CHOKE MOWER HEIGHT PARKING BRAKE UNLOCKED

LOCKED

R N H L

ATTACHMENT REVERSE NEUTRAL HIGH LOW

CLUTCH ENGAGED

KEEP AREA CLEAR SLOPE HAZARDS

(SEE SAFETY RULES SECTION)

IGNITION

ATTACHMENT

CLUTCH DISENGAGED

MOWER LIFT

PARKING BRAKE

DANGER, KEEP HANDS AND FEET AWAY

FREE WHEEL

(Automatic Models only)

OPERATION

KNOW YOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR

Compare the illustrationswith your tractor to familiarize yourself with thelocationsofvarious controls and adjustments. Save this manual for future reference.

IGNITION

ATTACHMENT CLUTCH LEVER

AMMETER

THROTTLE/ , LIFT LEVER

CHOKE PLUNGER CONTROL

SWITCH

GEAR 5 LEVER

LIGHT SWITCH POSITION

ATTACHMENT

LIFT LEVER

PARKING BRAKE

Our tractors conform to the safety standards of the American National Standards Institute.

ATTACHMENT CLUTCH LEVER: Used to engage the

mower blades, orother attachments mounted to you rtractor. LIGHT SWITCH POSITION: Turns the headlights on and

off. THROTTLE/CHOKE CONTROL: Used for starting and

controlling engine speed. CLUTCH/BRAKE PEDAL: Used for declutching and brak-

ing the tractor and starting the engine. PARKING BRAKE: Locks clutch/brake pedal intothe brake position.

FIG. 5

GEARSHIFT LEVER - Selects the speed and direction of the tractor.

ATTACHMENT LIFT LEVER: Used to raise, lower, and adjust the mower deck or other attachments mounted to your

tractor. LIFT LEVER PLUNGER: Used to release attachment lift

lever when changing its position. IGNITION SWITCH: Used for starting and stopping the

engine. AMMETER - Indicates charging (+) or discharging (-) of

battery.

OPERATION

The operation of anytractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating

your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig. 6)

Your tractor isequipped withan operator presence sensing switch. When engine isrunning,any attempt by the operator

to leave the seat withoutfirst setting the parking brake will shut off the engine.

• Depress clutch/brake pedal into full "BRAKE" position

and hold.

• Place parking brake lever in "ENGAGED" positionand release pressurefrom clutch/brake pedal. Pedal should

remain in"BRAKE" position. Make sure parking brake willhold tractorsecure.

ATTACHMENT CLUTCH

THROTTLE/

CHOKE CONTROL

LEVER

POSITION

CLUTCH/BRAKE PEDAL "DRIVE"

POSITION

FIG. 6

STOPPING (See Fig. 6)

MOWER BLADES -

• To stop mower blades,move attachment clutchlever to "DISENGAGED" position.

GROUND DRIVE-

• To stop ground drive, depress clutch/brake pedal into full "BRAKE" position.

• Move gearshift lever to neutral (N) position.

ENGINE -

• Move throttle control to slow position.

NOTE: Failureto move throttlecontroltoslow positionand allowingengine toidlebefore stopping may cause engine to

"backfire".

• Turn ignition key to "OFF" position and remove key. Always remove key when leaving tractor to prevent

unauthorizeduse.

• Never use choke to stop engine.

IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "OFF" WILL CAUSE THE

BATTERY TO BE DISCHARGED, (DEAD).

LEVER "ENGAGED" POSITION

IGNITION KEY

"DISENGAGED"

POSITION

.PARKING BRAKE

"ENGAGED"

POSITION

GEAR S LEVER

PARKING BRAKE

"DISENGAGED"

POSITION

NOTE: Under certain conditions when tractor isstanding idle

with the engine running, hot engine exhaust gases may cause "browning" of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

CAUTION: Always stop tractor com-

pletely, as described above, before leav- ing the operator's position; to empty

grass catcher, etc.

TO USE THROTTLE CONTROL (See Fig. 6)

Always operate engine at full throttle.

• Operating engine at less than full throttle reduces the battery charging rate.

• Full throttle offers the best bagging and mower perfor- mance.

TO MOVE FORWARD AND BACKWARD (See Fig. 6)

The direction and speed of movement is controlled by the

gearshift lever.

• Start tractor with clutch/brake pedal depressed and gearshift lever in neutral (N) position.

• Move gearshift lever to desired position.

• Slowly release clutch/brake pedal to start movement.

IMPORTANT: BRING TRACTOR TO A COMPLETE STOP BEFORE SHIFTING OR CHANGING GEARS. FAILURE TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR TRANSAXLE.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 6)

The position of the attachment lift lever determines the cuttingheight.

• Grasp liftlever.

• Press plunger with thumb and move lever to desired

position.

The cutting height range is approximately 1-1/2to 4". The heightsare measured from the groundtothe blade tipwiththe

engine notrunning. These heightsareapproximate and may vary depending upon soil conditions, height of grass and

types ofgrass being mowed.

• The average lawn should be cut to approximately 2-1/2 inchesduring the cool season andtoover3 inchesduring

hotmonths. For healthier and better lookinglawns, mow often and after moderate growth.

• For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut

relatively high; the second to desired height.

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly offthe groundwhen mower isat the desired cuttingheightin operating position. Gauge wheels then keep the deck in

proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level

surface.

• Adjust mower to desired cutting height (See "TO AD- JUST MOWER CUTTING HEIGHT" in the Operation

section of this manual).

• With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with

shoulder bolt, 3/8 washer, and 3/8-16 Iocknut and tighten securely.

• Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE WHEEL MOUNTING

3/8-16

LOCKNU1

318 WASHER' SHOULDER

GAUGE WHEEL" BOLT

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor isequipped withan operator presence sensing switch. Any attempt by the operator to leave the seat with

the engine running and the attachment clutch engaged will

shut off the engine.

• Select desired height of cut.

• Start mower blades by engaging attachment clutch

control.

• TO STOP MOWER BLADES - disengage attachment

clutch control.

without either the entire grass catcher,

_ AUTION: Do not operate the mower

on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

.3HMENT

LIFT LEVER HIGH POSITION

POSITION

ATTACHMENT CLUTCH LEVER

"DISENGAGED"

POSITION

CTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

with slopes greater than 15° and do not

CAUTION: Do not drive up or down hills drive across any slope.

• Choose the slowest speed before starting up or down hills.

• Avoid stopping or changing speed on hills.

• If slowing is necessary, move throttle control lever to slower position.

• If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking

brake.

• Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

• To restart movement, slowly release parking brake and clutch/brake pedal.

• Make all turns slowly.

TO TRANSPORT

• Raise attachment liftto highest position with attachment lift control.

• When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

• Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and

secu red to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your

tractor. Use common sense when towing. Too heavy of a load, while on a slope, isdangerous. Tires can lose traction

with the ground and cause you to lose control of your tractor.

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

• The engine in your tractor has been shipped, from the

factory, already filled with summer weight oil.

• Check engine oil with tractor on level ground.

• Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds,

remove and read oil level. If necessary, add oil until

"FULL" mark on dipstick is reached. Do not overfill.

• For cold weather operation you should change oil for easier starting (See "OIL VISCOSITY CHART" in the

Customer Responsibilities section of this manual).

• To change engine oil, see the Customer Responsibili-

ties section in this manual.

ADD GASOLINE

Fill fuel tankto bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum

of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life).

Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

A CAUTION: Wipe off any spilled oil or

IMPORTANT: When operating in temperatures

below32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting.

fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels(called gasohol or using ethanol or methanol)

can attract moisture which leads to sepa- ration and formation of acids during

storage. Acidic gas can damagethe fuel system of an engine while in storage. To

avoid engine problems, the fuel system should be emptied before storage of 30

days or longer. Drain the gas tan k, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage

Instructions for additional information. Never use engine or carburetor cleaner

products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 6)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel

from the tank to the engine.

• Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

• Place gear shift lever in neutral (N) position.

• Move attachment clutch to "DISENGAGED" position.

• Move throttle control to choke (1\1)position.

NOTE: Before starting, read the warm and cold starting procedures below.

• Insert key into ignition and turn key clockwise to "START" position and release key as soon as engine starts. Do not run starter continuously for more than

fifteen seconds per minute. Ifthe engine does not start after several attempts, move throttle control to fast

position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the

choke (1\1)position and retry.

WARM WEATHER STARTING (50° F and above)

• When engine starts, move the throttle control to the fast position.

• The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow itto warm up for one minute using the choke

as described above.

COLD WEATHER STARTING ( 50° F and below)

• When engine starts, allow engine to run with the throttle control in the choke (1\1)position until the engine runs

roughly, then move throttle control to fast position. This may require an engine warm-up period from several

seconds to several minutes, depending on thetempera- ture.

• The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F)the carburetor fuel mixture may

need to be adjusted for best engine performance. See "TO ADJUST CARBURETOR" in the Service and Adjustments section of this manual.

OPERATION

MOWING TIPS MULCHING MOWING TIPS

• Mower should be properly leveled for best mowing

performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.

• The left hand side of mower should beused for trimming.

• Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the

machine. This will result in a more even distribution of clippings and more uniform cutting.

• When mowing large areas, start by turning tothe right so that clippings will discharge away from shrubs, fences,

driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished

(See Fig. 9).

• If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip-

pings. Make first cut relatively high; the second to the desired height.

• Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. AIIowgrasstodry before mowing.

• Alwaysoperateengineatfullthrottlewhen mowing to assure better mowing performance and proper dis- charge of material. Regulate ground speed by selecting

a low enough gear to give the mower cutting perfor- mance as well as the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH.

CLEAN AFTER EACH USE.

• The special mulching blade will recutthe grass clippings many times and reduce them in size so that as they fall

onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade

quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will

provide the best recutting action of the blades.

• Avoid cutting you r lawn when itis wet. Wet grass tends to form clumps and interferes with the mulching action.

The best time to mow your lawn is the early afternoon. At this time the grass has dried and the newly cut area

will not be exposed to the direct sun.

• For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass

blades (See Fig. 10). For extremely heavy mulching, reduce your width of cut on each pass and mow slowly.

• Certain types of grass and grass conditions may require that an area be mulched a second time to completely

hide the clippings. When doing a second cut, mow across or perpendicular to the first cut path.

• Change your cutting pattern from week to week. Mow north to south one week then change to east to west the

next week. This will help prevent matting and graining of the lawn.

FIG. 9

,c J

MAX 1/3

FIG. 10

CUSTOMER RESPONSIBILITIES

,, sc. oo, "

ASYOUO0 PLE E .......

REGULAR SERVICE f__r_-_%'4y_¢'_ SERVICE DATES

Check Brake Operation V p V p Check Tire Pressure V p V D

Check Operator Presence and

T Interlock Systems

R Check for Loose Fasteners V p V_5

Sharpen/Replace Mower Blades VP3

T Lubrication Chart V _ V _

0 Check Battery Level _4

R Clean Battery and Terminals V _

Check Transaxle Cooling V p Check V-Belts V j

Check Engine Oil Level V j !_ Change Engine Oil (with oil filter) Vll,2 V I

E Change Engine Oil (without oil filter) VPl,2 V p

N Clean Air Filter VP2

G Clean Air Screen VP2

N_ Inspect Muffler/Spark Arrester V j

E Replace Oil Filter (If equipped) _1,2

Clean Engine Cooling Fins V' 2

Replace Spark Plug V' Replace Air Filter Paper Cartridge 1_2

Replace Fuel Filter

- Change more often when operating under a heavy load or in high ambient temperatures.

2 - Service more often when operating in dirty or dusty conditions.

3 - Replace blades more often when mowing in sandy soil. 4 - Not required if equipped with maintenance-free battery.

5 - Tighten front axle pivot bolt to 35 ft.-Ibs, maximum.

Do not overtighten.

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive

full value from the warranty, operator must maintain tractor as instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your tractor.

All adjustments in the Service and Adjustments section of this manual should be checked at least once each season.

• Once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel

mixture and help your engine run better and last longer.

BEFORE EACH USE

• Check engine oillevel.

• Check brake operation.

• Check tire pressure.

• Check operator presence and interlocksystems for proper operation.

• Check for loosefasteners.

LUBRICATION CHART

(_)SPINDLE

(_ FRONT "FRONT WHEEL(_)

BEARING t_ BEARING ZERK

ZERK

i I I i

I i

I ----I" 1-

i I I

1_ SAE 30 OR 10W30 MOTOR OIL 2_ GENERAL PURPOSE GREASE

® REFER TO CUSTOMER RESPONSIBILITIES "ENGINE"

SECTION

IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRI- CANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS. IF YOU

FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POW- DERED GRAPHITE TYPE LUBRICANT SPARINGLY.

PINDLE ZERK(_

GEARSHIFT(_

PIVOTS

+ 33 hidden pages

Poulan 917279870 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual