Poulan 530086536 User Manual

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

330 / 380

R

ENGLISH

ESPAÑOL

For Occasional Use Only

WARNING:

Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e en­strucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertisse­ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.

Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907

Copyright E2002 Electrolux Home Products, Inc.

Electrolux Canada Corporation

6150 McLaughlin Road

Mississauga, Ontario L5R 4C2

530086536 4/10/02

FRANÇAIS

IDENTIFICATION OF SYMBOLS

WARNING!

saw can be dangerous! Care­less or improper use can cause
serious or even fatal injury.

Always wear appropriate ear protection, eye protection and head protection.

This chain

Always use two hands when operating the chain saw.

WARNING!

should be avoided; tip contact may cause the guide bar to
move suddenly upward and backward, which may cause se­rious injury.

XX_

Measured maximum kickback value without chain brake for the bar
and chain combination on the label.

SAFETY RULES

WARNING:

spark plug wire and place wire where it can­not contact spark plug to prevent accidental
starting when setting up, transporting, ad­justing or making repairs except carburetor
adjustments.
Because a chain saw is a high-speed wood­cutting tool, special safety precautions must
be observed to reduce the risk of accidents.
Careless or improper use of this tool can
cause serious injury.

PLAN AHEAD

Read this manual carefully until you com-

S

pletely understand and can follow all safety
rules, precautions, and operating instruc­tions before attempting to use the unit.
Restrict the use of your saw to adult users

S

who understand and can follow safety
rules, precautions, and operating instruc­tions found in this manual.
Wear protective gear. Always use steel-

S

toed safety footwear with non-slip soles;
snug-fitting clothing; heavy-duty, non-slip
gloves; eye protection such as non-fogging,
vented goggles or face screen; an approved
safety hard hat; and sound barriers (ear
plugs or muf flers) to protect your hearing.
Regular users should have hearing checked
regularly as chain saw noise can damage
hearing. Secure hair above shoulder length.

Always disconnect

Read and understand the
instruction manual before
using the chain saw.

Contacting the guide bar tip with any object

Hearing

Protection

Snug
Fitting

Clothing

Safety
Shoes

Keep all parts of your body away from the

S

chain when the engine is running.
Keep children, bystanders, and animals a

S

minimum of 30 feet (10 meters) away from
the work area. Do not allow other people or
animals to be near the chain saw when
starting or operating the chain saw.
Do not handle or operate a chain saw

S

when you are fatigued, ill, or upset, or if you
have taken alcohol, drugs, or medication.
You must be in good physical condition
and mentally alert. Chain saw work is
strenuous. If you have any condition that
might be aggravated by strenuous work,
check with your doctor before operating a
chain saw.

Safety Hat

Eye
Protection

Heavy Duty
Gloves

Safety Chaps

2

Carefully plan your sawing operation in ad-

S

vance. Do not start cutting until you have a
clear work area, secure footing, and, if you
are felling trees, a planned retreat path.

OPERATE YOUR SAW SAFELY

Do not operate a chain saw with one hand.

S

Serious injury to the operator, helpers, by­standers or any combination of these per­sons may result from one-handed opera­tion. A chain saw is intended for
two-handed use.
Operate the chain saw only in a well-venti-

S

lated outdoor area.
Do not operate saw from a ladder or in a

S

tree.
Make sure the chain will not make contact

S

with any object while starting the engine.
Never try to start the saw when the guide
bar is in a cut.
Do not put pressure on the saw at the end

S

of the cut. Applying pressure can cause
you to lose control when the cut is com­pleted.
Stop the engine before setting the saw

S

down.
Do not operate a chain saw that is dam-

S

aged, improperly adjusted, or not com­pletely and securely assembled. Always
replace bar, chain, hand guard, or chain
brake immediately if it becomes damaged,
broken or is otherwise removed.
With the engine stopped, hand carry the

S

chain saw with the muffler away from your
body, and the guide bar and chain to the
rear, preferably covered with a scabbard.

MAINTAIN YOUR SAW IN GOOD
WORKING ORDER

Have all chain saw service performed by a

S

qualified service dealer with the exception
of the items listed in the maintenance sec­tion of this manual. For example, if improp­er tools are used to remove or hold the fly­wheel when servicing the clutch, structural
damage to the flywheel can occur and
cause the flywheel to burst.
Make certain the saw chain stops moving

S

when the throttle trigger is released. For
correction, refer to CARBURETOR AD­JUSTMENTS.
Never modify your saw in any way.

S

Keep the handles dry, clean, and free of oil

S

or fuel mixture.
Keep fuel and oil caps, screws, and fas-

S

teners securely tightened.
Use only Poulan PRORaccessories and

S

replacement parts as recommended.

HANDLE FUEL WITH CAUTION

Do not smoke while handling fuel or while

S

operating the saw.
Eliminate all sources of sparks or flame in

S

the areas where fuel is mixed or poured.
There should be no smoking, open flames,
or work that could cause sparks. Allow en­gine to cool before refueling.
Mix and pour fuel in an outdoor area on

S

bare ground; store fuel in a cool, dry, well
ventilated place; and use an approved,
marked container for all fuel purposes.

Wipe up all fuel spills before starting saw.
Move at least 10 feet (3 meters) from fuel-

S

ing site before starting engine.
Turn the engine off and let saw cool in a

S

non-combustible area, not on dry leaves,
straw, paper, etc. Slowly remove fuel cap
and refuel unit.
Store the unit and fuel in an area where fuel

S

vapors cannot reach sparks or open
flames from water heaters, electric motors
or switches, furnaces, etc.

KICKBACK

WARNING:

can result in serious injury. Kickback is the
backward, upward or sudden forward motion
of the guide bar occurring when the saw
chain near the upper tip of the guide bar con­tacts any object such as a log or branch, or
when the wood closes in and pinches the
saw chain in the cut. Contacting a foreign ob­ject in the wood can also result in loss of
chain saw control.

Rotational Kickback can occur when the

S

moving chain contacts an object at the up­per tip of the guide bar. This contact can
cause the chain to dig into the object,
which stops the chain for an instant. The
result is a lightning fast, reverse reaction
which kicks the guide bar up and back to­ward the operator.
Pinch-Kickback can occur when the the

S

wood closes in and pinches the moving
saw chain in the cut along the top of the
guide bar and the saw chain is suddenly
stopped. This sudden stopping of the
chain results in a reversal of the chain
force used to cut wood and causes the
saw to move in the opposite direction of the
chain rotation. The saw is driven straight
back toward the operator.
Pull-In can occur when the moving chain

S

contacts a foreign object in the wood in the
cut along the bottom of the guide bar and the
saw chain is suddenly stopped. This sudden
stopping pulls the saw forward and away
from the operator and could easily cause the
operator to lose control of the saw .

Avoid Pinch--Kickback:

Be extremely aware of situations or ob-

S

structions that can cause material to pinch
the top of or otherwise stop the chain.
Do not cut more than one log at a time.

S

Do not twist the saw as the bar is with-

S

drawn from an undercut when bucking.

Avoid Pull --In:

Always begin cutting with the engine at full

S

speed and the saw housing against wood.
Use wedges made of plastic or wood.

S

Never use metal to hold the cut open.

Avoid kickback which

Kickback Path

3

Avoid Obstructions

Clear The Working Area

REDUCE THE CHANCE OF
KICKBACK

Recognize that kickback can happen.

S

With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
Never let the moving chain contact any ob-

S

ject at the tip of the guide bar.
Keep the working area free from obstruc-

S

tions such as other trees, branches, rocks,
fences, stumps, etc. Eliminate or avoid
any obstruction that your saw chain could
hit while you are cutting. When cutting a
branch, do not let the guide bar contact
branch or other objects around it.
Keep your saw chain sharp and properly

S

tensioned. A loose or dull chain can in­crease the chance of kickback occurring.
Follow manufacturer ’s chain sharpening
and maintenance instructions. Check ten­sion at regular intervals with the engine
stopped, never with engine running. Make
sure the chain brake nuts are securely
tightened after tensioning the chain.
Begin and continue cutting at full speed. If

S

chain is moving at a slower speed, there is
greater chance of kickback occurring.
Cut one log at a time.

S

Use extreme caution when re-entering a

S

previous cut.
Do not attempt cuts starting with the tip of

S

the bar (plunge cuts).
Watch for shifting logs or other forces that

S

could close a cut and pinch or fall into chain.
Use Reduced-Kickback Guide Bar and Low-

S

Kickback Chain specified for your saw.

MAINTAIN CONTROL

Stand to the left of
the saw

Thumb on
underside of
handlebar

Never reverse
hand positions

Elbow locked

Thumb on underside of
handlebar

Keep a good, firm grip on the saw with both

S

hands when the engine is running and
don’t let go. A firm grip will help you reduce
kickback and maintain control of the saw.
Keep the fingers of your left hand encir­cling and your left thumb under the front
handlebar. Keep your right hand complete­ly around the rear handle whether your are
right handed or left handed. Keep your left
arm straight with the elbow locked.
Position your left hand on the front handle-

S

bar so it is in a straight line with your right
hand on the rear handle when making
bucking cuts. Never reverse right and left
hand positions for any type of cutting.
Stand with your weight evenly balanced on

S

both feet.
Stand slightly to the left side of the saw to

S

keep your body from being in a direct line
with the cutting chain.
Do not overreach. You could be drawn or

S

thrown off balance and lose control of saw.
Do not cut above shoulder height. It is diffi-

S

cult to maintain control of saw above
shoulder height.

KICKBACK SAFETY FEATURES

WARNING:

are included on your saw to help reduce the
hazard of kickback; however, such features
will not totally eliminate this dangerous reac­tion. As a chain saw user, do not rely only on
safety devices. You must follow all safety
precautions, instructions, and maintenance
in this manual to help avoid kickback and
other forces which can result in serious
injury.

Reduced-Kickback Guide Bar, designed

S

with a small radius tip which reduces the
size of the kickback danger zone on bar
tip. A Reduced-Kickback Guide Bar has
been demonstrated to significantly reduce
the number and seriousness of kickbacks
when tested in accordance with safety re­quirements for gasoline powered chain
saws as set by ANSI B175.1.

Reduced Kickback Symmetrical Guide Bar

The following features

Small Radius Tip

4

Symmetrical Guide Bar

Large Radius Tip

Low-Kickback Chain, designed with a con-

S

toured depth gauge and guard link which de­flect kickback force and allow wood to gradu­ally ride into the cutter. Low-Kickback Chain
has met kickback performance require­ments when tested on a representative sam­ple of chain saws below 3.8 cubic inch
displacement specified in ANSI B175.1.

Contoured Depth Gauge

Elongated Guard Link

Deflects kickback
force and allows

Low--Kickback
Chain

Not a Low--Kickback Chain

Front Handguard, designed to reduce the

S

chance of your left hand contacting the chain
if your hand slips off the front handlebar.
Position of front and rear handlebars, de-

S

signed with distance between handles and
“in-line” with each other. The spread and “in­line” position of the hands provided by this
design work together to give balance and re­sistance in co ntrolling the pivot of the saw
back toward the operator if kickback occurs.

wood to gradually
ride into cutter

Can Obstruct
Material

CHAIN BRAKE

Chain Brake, designed to stop the chain in

S

the event of kickback.

WARNING:

RESENT AND YOU SHOULD NOT AS­SUME THAT THE CHAIN BRAKE WILL
PROTECT YOU IN THE EVENT OF A
KICKBACK. Kickback is a lightning fast ac­tion which throws the bar and rotating chain
back and up toward the operator. Kickback
can be caused by allowing contact of the bar
tip in the danger zone with any hard object.
Kickback can also be caused by pinching the

WE DO NOT REP-

saw chain along the top of the guide bar. This
action may push the guide bar rapidly back
toward the operator. Either of these events
may cause you to lose control of the saw
which could result in serious injury or even
death. DO NOT RELY UPON ANY OF THE
DEVICES BUILT INTO YOUR SAW. YOU
SHOULD USE THE SAW PROPERLY AND
CAREFULLY TO AVOID KICKBACK. Re­duced--kickback guide bars and low--kick­back saw chains reduce the chance and
magnitude of kickback and are recom­mended. Your saw has a low kickback chain
and bar as original equipment. Repairs on a
chain brake should be made by an autho­rized servicing dealer. Take your unit to the
place of purchase if purchased from a ser­vicing dealer, or to the nearest authorized
master service dealer.

Tip contact in some cases may cause a

S

lightning fast reverse REACTION, kicking
guide bar up and back toward operator.
Pinching the saw chain along the top of the

S

guide bar may push the guide bar rapidly
back toward the operator.
Either of these reactions may cause you to

S

lose control of the saw which could result
in serious injury. Do not rely exclusively
upon safety devices built into your saw.

WARNING:

angle (CKA) listed on your saw and listed in
the CKA table below represents angle of
kickback your bar and chain combinations
will have when tested in accordance with
CSA and ANSI standards. When purchasing
replacement bar and chain, considerations
should be given to the lower CKA values.
Lower CKA values represent safer angles to
the user, higher values indicate more angle
and higher kick energies. Computed angles
represented in the non-activated column in­dicate total energy and angle associated
without activation of the chain brake during
kickback. Activated angle represents chain
stopping time relative to activation angle of
chain brake and resulting kick angle of saw.
In all cases lower CKA values represent a
safer operating environment for the user.

The following guide bar and chain combina­tions meet kickback requirements of CSA
Z62.1, Z62.3, & ANSI B175.1 when used on
saws listed in this manual. Use of bar and
chain combinations other than those listed is
not recommended and may not meet the
CKA requirements per standard.

Computed kickback angle (CKA) Table

MODEL

330
380 21

: If this saw is to be used for commer-

NOTE

cial logging, a chain brake is required and shall
not be removed or otherwise disabled to com-

952044701 20!
952044701 952051266

BAR

P/N Length

20!

CHAIN P/N

952051266

952051459530044833330 22!

ply with Federal OSHA Regulations for Com­mercial Logging.

5

Computed kickback

CKA without

chain brake

_

21

_

_

23

SAFETY NOTICE:

vibrations through prolonged use of gasoline
powered hand tools could cause blood
vessel or nerve damage in the fingers,
hands, and joints of people prone to
circulation disorders or abnormal swellings.
Prolonged use in cold weather has been
linked to blood vessel damage in otherwise
healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in
skin color or texture, or loss of feeling in the
fingers, hands, or joints, discontinue the use
of this tool and seek medical attention. An
anti-vibration system does not guarantee the
avoidance of these problems. Users who
operate power tools on a continual and
regular basis must monitor closely their
physical condition and the condition of this
tool.

SPECIAL NOTICE:

with a temperature limiting muffler and spark
arresting screen which meets the
requirements of California Codes 4442 and

4443. All
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require
many internal combustion engines to be
equipped with a spark arresting screen by
law. If you operate a chain saw in a state or
locale where such regulations exist, you are
legally responsible for maintaining the
operating condition of these parts. Failure to
do so is a violation of the law. Refer to the
SERVICE section for maintenance of the
spark arresting screen.

Failure to follow all Safety Rules and Precau­tions can result in serious injury. If situations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your authorized service
dealer.

STANDARDS:

derwriter ’s Laboratories, Inc., in accordance
with:

ANSI B175.1-2000 American National
Standard for Powered Tools -- Gasoline
Powered Chain Saw -- Safety Requirements

CSA Z62.1--1995 Chain Saws -- Occupa­tional Health and Safety

CSA Z62.3--1996 Chain Saw Kickback Oc­cupational Health and Safety

forest land and the states of

U.S.

This saw is listed by Un-

Exposure to

Yoursaw is equipped

Loosen and remove the chain brake nuts

S

and the chain brake from the saw.
Remove the plastic shipping spacer (if

S

present).

Shipping
Spacer

Assembly
Tool

An adjusting pin and screw is used to ad-

S

just the tension of the chain. It is very im­portant when assembling the bar, that the
pin located on the adjusting screw aligns
into a hole in the bar. Turning the screw will
move the adjustment pin up and down the
screw. Locate this adjustment before you
begin mounting the bar onto the saw. See
illustration below.

Turn the adjusting screw counterclock-

S

wise to move the adjusting pin almost as
far as it will go to the rear. This should allow
the pin to be near the correct position. Fur­ther adjustment may be necessary as you
mount the bar.
Slide guide bar behind clutch drum until

S

guide bar stops agaist clutch drum sprocket.

Chain Brake

Chain Brake Nuts

Mount the bar

Adjustment
Screw

ASSEMBLY

Protective gloves (not provided) should be
worn during assembly.

ATTACHING THE BAR & CHAIN

already attached)

WARNING:

repeat all steps to ensure your saw is proper­ly assembled and all fasteners are secure.
Always wear gloves when handling the
chain. The chain is sharp and can cut you
even when it is not moving!

If received assembled,

(If not

Carefully remove the chain from the pack-

S

age. Hold chain with the drive links as
shown.

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

6

Tip of
Bar