Poulan 2050WT User Manual

Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.

1--800--554--6723

www.poulan.com

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

1950 / 1975 / 2050 / 2055 / 2075
2150 / 2155 / 2175 / 2350 / 2375

2050WT / 2150PR

For Occasional Use Only

ENGLISH

R

ESPAÑOL

WARNING:

Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e en­strucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertisse­ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.

Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907

CopyrightE2003 ElectroluxHome Products, Inc.

Electrolux Canada Corporation

6150 McLaughlin Road

Mississauga, Ontario L5R 4C2

530163675 6/26/03

FRANÇAIS

IDENTIFICATION OF SYMBOLS

WARNING!

saw can be dangerous! Care­less orimproper usecancause
serio us or even fatal injury.

Alwayswearappropriateearprotection,eye protectionandheadprotection.

XX_

Measuredmaximum kickback value withoutchain brake for thebar
and chain combination on the label.

This chain

Always use two hands whenoperating the chain saw.

WARNING!

should be avoided; tip contact may cause the guide bar to
movesuddenlyupwardand backward,whichmay causese­rious injury.

SAFETY RULES

WARNING:

spark plug wire andplace wire where it can­not contact spark plug to preventaccidental
starting when setting up, transporting, ad­justing or making repairs except carburetor
adjustments.
Becauseachain saw is a high-speedwood­cutting tool, special safety precautions must
beobserved to reduce the risk of accidents.
Careless or improper use of this tool can
cause serious injury.

PLAN AHEAD

Read this manual carefully until you com-

S

pletely understand and can follow all safety
rules, precautions, and operating instruc­tions before attempting to use the unit.
Restrict theuse ofyour saw to adultusers

S

who understand and can follow safety
rules, precautions, and operating instruc­tions found in this manual.
Wear protective gear. Always use steel-

S

toed safety footwear with non-slip soles;
snug-fitting clothing; heavy-duty, non-slip
gloves; eye protection such as non-fog­ging, vented goggles or face screen; an
approvedsafety hardhat; andsoundbarri­ers (ear plugs or mufflers) to protect your
hearing. Regular users should have hear­ing checked regularly as chain saw noise
can damage hearing. Secure hair above
shoulder length.

Always disconnect

Read and understand the
instruction manual before
using the chain saw.

Contactingthe guide bar tip with any object

Hearing

Protection

Snug
Fitting

Clothing

Safety
Shoes

Keepall parts of your body away from the

S

chain when the engine is running.
Keepchildren, bystanders, and animals a

S

minimum of30feet(10meters)awayfrom
the work area. Do not allow other people
or animals to be near the chain saw when
starting or operating the chain saw.
Do not handle or operate a chain saw when

S

you are fatigued, ill, or upset, or if youhave
taken alcohol, drugs, or medication. You
must be in goodphysical condition and men­tally alert. Chain saw work is strenuous. If
you have any condition that might be aggra­vated by strenuous work, check with your
doctor before operating a chain saw.

Safety Hat

Eye
Protection

Heavy Duty
Gloves

Safety Chaps

2

Carefullyplanyour sawing operationinad-

S

vance. Do notstartcuttinguntil you havea
clearwork area,securefooting,and, if you
are felling trees, a planned retreat path.

OPERATE YOUR SAWSAFELY

Donotoperateachain saw with one hand.

S

Serious injury to the operator,helpers, by­standers or any combination of these per­sons may result from one-handed opera­tion. A chain saw is intended for
two-handed use.
Operatethe chain saw onlyin a well-venti-

S

lated outdoor area.
Do not operate saw from a ladder or in a

S

tree.
Makesurethechain will not make contact

S

with any object while starting the engine.
Never try to start the saw when the guide
bar is in a cut.
Do not put pressure on the saw at the end

S

of the cut. Applying pressure can cause
you to lose control when the cut is com­pleted.
Stop the engine before setting the saw

S

down.
Do not operate a chain saw that is dam-

S

aged, improperly adjusted, or not com­pletely and securely assembled. Always
replace bar, chain, hand guard, or chain
brakeimmediately if it becomes damaged,
broken or is otherwise removed.
With the engine stopped, hand carry the

S

chain saw with the muffler away from your
body, and the guide bar and chain to the
rear,preferably covered with a scabbard.

MAINTAIN YOUR SAW IN GOOD
WORKINGORDER

Haveall chain saw service performedbya

S

qualified service dealer with the exception
of theitems listed in the maintenancesec­tionofthis manual. For example, ifimprop­ertools are used to removeor hold the fly­wheelwhen servicing the clutch, structural
damage to the flywheel can occur and
cause the flywheel to burst.
Make certain the saw chain stops moving

S

when the throttle trigger is released. For
correction, refer to CARBURETOR AD­JUSTMENTS.
Never modify your saw in any way.

S

Keepthe handles dry,clean, andfreeofoil

S

or fuel mixture.
Keep fuel and oil caps, screws, and fas-

S

teners securely tightened.
Use only PoulanRaccessories and re-

S

placement parts as recommended.

HANDLE FUEL WITH CAUTION

Do not smoke while handling fuel or while

S

operating the saw.
Eliminate all sources of sparks or flame in

S

the areas where fuel is mixed or poured.
Thereshouldbe nosmoking,openflames,
orworkthat couldcausesparks. Allowen­gine to cool before refueling.
Mix and pour fuel in an outdoor area on

S

bare ground; store fuel in a cool, dry,well
ventilated place; and use an approved,

marked container for all fuel purposes.
Wipe up all fuel spills beforestartingsaw.
Move at least 10 feet (3meters) from fuel-

S

ing site before starting engine.
Turn the engine off and let saw cool in a

S

non-combustible area, not on dry leaves,
straw,paper ,etc. Slowly remove fuel cap
and refuel unit.
Storetheunit andfuel in anarea wherefuel

S

vapors cannot reach sparks or open
flamesfrom waterheaters,electric motors
or switches, furnaces, etc.

KICKBACK

WARNING:

can result in serious injury. Kickbackis the
backward,upwardorsuddenforwardmotion
of the guide bar occurring when the saw
chainnearthe uppertip of theguidebar con­tacts any object such as a log or branch, or
when the wood closes in and pinches the
sawchaininthecut. Contactingaforeignob­ject in the wood can also result in loss of
chain saw control.

RotationalKickbackcan occur when the

S

moving chain contacts an object at theup­per tip of the guide bar. This contact can
cause the chain to dig into the object,
which stops the chain for an instant. The
result is a lightning fast, reverse reaction
which kicks the guide bar up and back to­ward the operator.
Pinch-Kickback can occur when the the

S

wood closes in and pinches the moving
saw chain in the cut along the top of the
guide bar and the saw chain is suddenly
stopped. This sudden stopping of the
chain results in a reversal of the chain
force used to cut wood and causes the
sawtomovein theoppositedirectionof the
chain rotation. The saw is driven straight
back toward the operator.
Pull-In can occur when the moving chain

S

contacts a foreign object in the wood in the
cut along the bottom of the guide bar andthe
sawchainis suddenly stoppe d. Thissudden
stopping pulls the saw forward and away
from the operator and couldeasily cause the
operator to lose control of the saw.

Avoid Pinch--Kickback:

Be extremely aware of situations or ob-

S

structions that can cause material topinch
the top of or otherwise stop the chain.
Do not cut more than one log at a time.

S

Do not twist the saw as the bar is with-

S

drawn from an undercut when bucking.

AvoidPull--In:

Always begin cuttingwith theengineatfull

S

speedandthesawhousing against wood.
Use wedges made of plastic or wood.

S

Never use metal to hold the cut open.

Avoid kickback which

Kickback Path

3

Avoid Obstructions

Clear The Working Area

REDUCETHE CHANCE OF
KICKBACK

Recognize that kickback can happen.

S

With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
Neverletthemoving chain contact anyob-

S

ject at the tip of the guide bar.
Keep the working area free from obstruc-

S

tionssuchasothertrees,branches,rocks,
fences, stumps, etc. Eliminate or avoid
any obstructionthat your saw chain could
hit while you are cutting. When cutting a
branch, do not let the guide bar contact
branch or other objects around it.
Keep your saw chain sharp and properly

S

tensioned. A loose or dull chain can in­crease the chance of kickback occurring.
Follow manufacturer’s chain sharpening
andmaintenanceinstructions. Checkten­sion at regular intervals with the engine
stopped, never with the engine running.
Make sure the chain brake nuts are se­curely tightenedafter tensioning thechain.
Begin andcontinue cutting at full speed. If

S

the chain is moving at a slower speed,
thereis greater chance of kickback occur­ring.
Cut one log at a time.

S

Use extreme caution when re-entering a

S

previous cut.
Do not attempt cuts starting with the tip of

S

the bar (plunge cuts).
Watch for shifting logs or other forces that

S

could close a cut and pinch or fall into
chain.
Use the Reduced--Kickback Guide Bar

S

and Low--Kickback Chain specified for
your saw.

MAINTAIN CONTROL

Stand to the
left of the saw

Thumb on
underside of
handlebar

Never reverse
hand positions

Elbow locked

Thumb on underside of
handlebar

Keep a good, firm grip on the saw with both

S

hands when the engine is running and don’t
letgo. A firm grip will help you reducekick­backandmaintaincontr ol of the saw. Keep
the fing ers of your left hand encirclin g and
your left thumb under the front handlebar.
Keep your right hand completely around the
rearhandle whether your are right handedor
left handed. Keep your left arm straight with
the elbowlocked .
Position your left hand on the fronthandle-

S

bar so it is in a straight line with your right
hand on the rear handle when making
bucking cuts. Never reverseright and left
hand positions for any type of cutting.
Standwithyourweightevenly balancedon

S

both feet.
Stand slightly to the left side of the saw to

S

keep your body from being in a direct line
with the cutting chain.
Do not overreach. You could be drawn or

S

thrown off balance and lose control of the
saw.
Donot cut above shoulderheight. Itis diffi-

S

cult to maintain control of saw above
shoulder height.

KICKBACKSAFETY FEATURES

WARNING:

are included on your saw to help reducethe
hazard of kickback; however, such features
will not totally eliminate this danger. As a
chainsawuser,donotrelyonlyonsafety de­vices. You must follow all safety precau­tions, instructions, and maintenance in this
manual to help avoid kickback and other
forces which can result in serious injury.

Reduced--Kickback Guide Bar, designed

S

with a small radius tip which reduces the
size of the kickback danger zone on the
bar tip. A Reduced--Kickback Guide Bar
hasbeendemonstratedto significantly re­ducethenumberandseriousness of kick­backs when tested in accordance with
safety requirementsfor gasoline powered
chain saws as set by ANSI B175.1.

Reduced Kickback Symmetrical Guide Bar

The following features

Small Radius Tip

4

Symmetrical Guide Bar

Low--Kickback Chain, designed with a

S

contoured depth gauge and guard link
which deflect kickback force and allow
woodto gradually ride into thecutter.Low-­Kickback Chain has met kickback per­formance requirements when tested on a
representative sample of chain saws be­low 3.8 cubic inch displacement specified
in ANSI B175.1.

Low---Kickback

Chain

Not a Low--- Kickback Chain

Front Hand Guard, designed to reduce the

S

chance of your lefthandcontacting thechain
if your hand slips off the front handlebar.
Position of front and rear handlebars, de-

S

signedwithdistancebetweenhandlesand
“in-line” with each other. The spread and
“in-line” position of the hands provided by
this design work together to give balance
and resistance in controlling the pivot of
the saw back toward the operator if kick­back occurs.

CHAIN BRAKE AND CKA ANGLE

Chain Brake, designed to stopthechain in

S

the event of kickback.

WARNING:

RESENT AND YOU SHOULD NOT AS­SUME THAT THE CHAIN BRAKE WILL
PROTECT YOU IN THE EVENT OF A
KICKBACK. Kickback is a lightning fast ac­tion which throws the bar and rotating chain
back and up toward the operator. Kickback
canbecaused by allowing contactof thebar
tip in the danger zone with any hard object.
Kickback canalsobecausedby pinchingthe
sawchain alongthe topoftheguidebar. This

Contoured Depth Gauge

Large Rad ius Tip

Elongated Guard Link

Deflects
kickback force
and allows wood
to gradually ride
into cutter

Can Obstruct Material

WE DO NOT REP-

action may push the guide bar rapidly back
toward the operator. Either of these events
may cause you to lose control of the saw
which could result in serious injury or even
death. DO NOT RELYUPON ANY OF THE
DEVICES BUILT INTO YOUR SAW. YOU
SHOULDUSETHESAW PROPERLYAND
CAREFULLY TO AVOID KICKBACK. Re­duced--kickback guide bars and low--kick­back saw chains reduce the chance and
magnitude of kickback and are recom­mended. Yoursaw hasalowkickback chain
andbar as original equipment. Repairs ona
chain brake should be made by an autho­rized servicing dealer. Take your unit to the
place of purchase if purchased from a ser­vicing dealer, or to the nearest authorized
master service dealer.

Tipcont act insomecasesmaycausealight-

S

ning fast reverse REACTION, kicking guide
bar up and back toward operator.
Pinching the saw chain along the top of the

S

guide bar may push the guide bar rapidly
back toward the operator .
Either of these reactions may cause you to

S

lose control of the saw which could result in
serious injury. Do not rely exclusively upon
devices builtinto your saw.

WARNING:

angle (CKA) listedonyoursaw andlisted inthe
CKA table below represents angle of kickback
your bar and chain combinations will have
when tested in accord ance with CSA (Cana­dian Standards Association) and ANSI stan­dards. When purchasing replacement bar and
chain, considerations should be given to the
lower CKA values. Lower CKA values repre­sent safer angles to the user, higher values in­dicate more angle and higher kick energies.
Computed ang les represented indicate total
energy and angle associated without activation
of the chain brake during kickback. Activated
anglerepresentschain stopping time relative to
activation angle of chain break and resulting
kick angle of saw. In all cases lower CKA val­ues represent a safer operating environment
for the user.
The following guide bar and chain combina­tions meet kickback requirements of CSA
Standards Z62.1, Z62.3, & ANSI B175.1 when
used on saws listed in this manual. Use of bar
and chain combinations other than those listed
is not recommended and may not meet the
CKA requirements per standard.

Computed kickback

Computed kickback angle (CKA) Table

BAR

MODEL

1950/1975/

2050/2050WT

2055/2075/

2150/2150PR

2155/2175/

2350/2375

P/N Length CHAIN P/N

952044368 14!

952044370

952044418

952051209

16!

952051211

18! 14

952051338

5

CKA without chain brake

24

_

19

_

_

NOTE:

r

mercial logging, a chain brake is required
and shall not be removed or otherwise dis­abledtocomply with Federal OSHA Regula­tions for Commercial Logging.

SAFETY NOTICE:

through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or
abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel
damage in otherwise healthy people. If
symptoms occur such as numbness, pain,
loss of strength,changein skincolor or texture,
or loss of feeling in the fingers, hands, orjoints,
discontinue the use of this tool and seek
medical attention. An anti-vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the
condition of this tool.

SPECIALNOTICE:

with a temperaturelimiting muffler andspark
arresting screen which meets the
requirements of California Codes 4442 and

4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines
tobeequippedwithaspark arrestingscreen.
Ifyou operateachainsaw inastate or locale
wheresuch regulationsexist, you are legally
responsible for maintaining the operating
condition of these parts. Failure to do so is
aviolation of the law. Refer to the SERVICE
section for maintenance of the spark
arresting screen.

Failuretofollowall SafetyRulesandPrecau­tionscanresult in serious injury. Ifsituations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your authorized service
dealer or call 1-800--554--6723.

STANDARDS:

writer’s Laboratories, Inc., in accordance with:
ANSI B175.1--2000 American National

Standards for Gasoline--Powered Chain
Saws -- Safety Requirements
CSA Z62.1--1995 Chain Saws -- Occupa­tional Health and Safety
CSA Z62.3--1996 Chain Saw Kickback Oc­cupational Health and Safety

If this saw is to be used for com-

Exposure to vibrations

Y oursaw is equipped

Thissaw is listedby Under-

ASSEMBLY

Protective gloves (not provided) should be
wornduringassembly.

ATTACHINGTHEBAR& CHAIN

already attached)

WARNING:

repeat all steps to ensure your saw is properly
assem b led and all fasten ers are secure . Al­ways wear gloves when handling the chain.

If received assembled,

(Ifnot

Thechain is sharp and can cut you even when
it is not moving!

1. Loosenandremovethechain brakenuts
and the chain brake from the saw.

2. Remove the plastic shipping spacer (if
present).

Chain Brake

3. Anadjus ting pin and screw is usedtoad­just the tension of the chain. It is very im­portant when assembling the bar, that the
pin located on the adjusting screw aligns
intoaholein thebar.Turning thescrewwill
move the adjustment pin up and down the
screw. Locate this adjustment before you
begin mounting the bar onto the saw. See
illustration below.

Adjustment located on Chain Brake

4. Turnthe adjusting screw by hand coun­terclockwise until the adjusting pin just
touches the stop. This should allow the
pin to be near the correct position.

5. Slide guide bar behind clutch drum until
guide bar stops against clutch drum
sprocket.

6. Carefully remove the chain from the pack­age. Hold chain with the drive links as
shown .

Location of shipping space

Chain Brake

Nuts

Bar Tool

Inside view of
Chain Brake

Mount the Bar

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

Tip of
Bar

6

Cutters

Drive Links

Depth Gauge

Checking the tension:

Use the screwdriver endof the chain adjust­menttool (bartool) to move the chain around
the bar. If the chain does not rotate, it is too
tight. If tooloose, thechainwill sagbelowthe
bar.

Place chain onto the sprocket

7. Place chain over and behind clutch, fitting
thedrivelinks in theclutchdrumsprocket .

8. Fit bottom of drive links between the
teeth in the sprocket in the nose of the
guide bar.

9. Fit chain drive links into bar groove.

10. Pull guide barforward until chain is snug
in guide bar groove. Ensure all drive
links are in the bar groove.

NOTE: CHAIN BRAKE MUST BE
DISENGAGED BEFORE INSTALLA­TIONON THESAW. TODISENGAGE
CHAIN BRAKE, PULL THE FRONT
HANDGUARD BACK TOWARDTHE
REAR OF THE CHAIN BRAKE AS
FARAS POSSIBLE(SEEILLUSTRA­TION).

DISENGAGED

Front Hand Guard

ENGAGED

Chain Brake

11. Now,install chain brake making surethe
adjusting pin is positioned in the lower
holein the guidebar. Remember this pin
moves the bar forward and backward as
the screw is turned.

12. Install chain brakenutsand fingertighten
only. Once the chain is tensioned, you
will need to tighten chain brake nuts.

CHAIN TENSION

(Including units with chain already installed)

NOTE:

make sure the chain brake nuts are finger
tight only. Attempting to tension the chain
when the chain brake nuts are tight can
cause damage.

When adjusting chain tension,

Chain Brake Nuts

Adjusting the tension:

Chain tension is very important. Chain
stretches during use. This is especially true
during the first few times you use your saw.
Always check chain tension each time you
use and refuel your saw.

Y oucan adjust the chain tension by loosen­ing the chain brake nuts and turning the ad­justing screw 1/4of a turnwhile lifting upon
the bar.

Ifchain is tootight, turnadjustingscrew1/4

S

turn counterclockwise.
If chain is too loose, turn adjusting screw

S

1/4 turn clockwise.

Chain Brake Nuts

Adjusting Screw -- 1/4 Turn

Lift up the tip of the barand securely tight-

S

en the chain brake nuts with the bar tool.
Recheck chain tension.

S

WARNING:

with a loose chain, the chain could jump off
the guide bar and result in serious injury.

Chain Adjustment

Tool (Bar T ool)

Adjusting

Screw

Chain Brake
Nuts

If the saw is operated

Guide Bar

7

OPERATION

KNOW YOUR CHAINSAW

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
CHAINSAW. Comparetheillustrationswith your unit to familiarize yourself with the location of
the various controls and adjustments. Save this manual for future reference.

Chain

Adjustment Tool

(Bar Tool)

Chain

Front Hand Guard

Muffler

Front Handle

Starter Rope

ON/STOP
Switch

Primer
Bulb

Bar Oil Fill Cap

Cylinder Cover

Fast Idle
Lock

Throttle
Lockout

Rear
Handle

Throttle
Trigger

ON/STOP SWITCH

The ON/STOP SWITCH is used to stop the
engine.

THROTTLE TRIGGER

The THROTTLE TRIGGER controls engine
speed.

THROTTLE LOCK--OUT

The THROTTLE LOCK--OUT must be
pressed before you can squeeze the throttle
trigger. This feature prevents you from acci­dentally squeezing the trigger.

FAST IDLE LOCK

TheFAST IDLE LOCK holdsthe throttletrigger
in the starting position. Activate the fast idle
lock by pressing the throttle lockou t and
squeezing the throttle trigger. With the throttle
trigger squeezed, press the fast idle lock. Re­lease the throttle lockout and triggerwhile hold­ing the fast idle lock button .

CHOKE KNOB

The CHOKE KNOB activates the choke to
provide additional fuel to the engine during cold
starting.

Choke
Knob

Chain
Brake

Chain
Catcher

Adjusting
Screw

Starter
Housing

Chain Brake
Nuts

Fuel Mix Fill Cap

Guide Bar

Bar
Sprocket
Hole

PRIMER BULB

ThePRIMERBULB circulat es fuel to the car­buretor to provide quickerstart ing.

CHAIN BRAKE

The CHAIN BRAK E is a dev ice designed to
stop the chain if kickback occurs. The chain
brake activates automatically in the event of
kickback. The chain brakeactivatesmanually
if the front hand guard is pushed forward. The
chainbrake is diseng aged by pulling thefront
hand guard back toward the front handle as far
as possible.

CHAIN TENSION

Itis normal for anewchain tostretch during first
15 minutes of operation. Y o u should check
your chain tension frequently. See CHAIN
TENSION under the ASSEMBLY section.

WARNING:

ingandafter use. Donot touch the muffler or
allow combustible material such as dry
grass or fuel to do so.

Muffler is very hot dur-

Chain
Direction
of Travel

8

FUELING & LUBRICATION

STARTING

WARNING:

when refueling.

FUELING ENGINE

This engine is certified to operate on un­leaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/Weed Eater
brand synthetic oil is recommended. Mix
gasolineandoil at a ratio of40:1. A40:1ratio
is obtainedby mixing 3.2ounces(95ml)ofoil
with 1 ga llon (4 liters) of unleaded gasoline.
Includedwiththis sawisa3.2 ouncecontain­erofoil. Pour the entire contents of this con­tainerinto 1 gallonofgasolineto achievethe
proper fuel mixture.

DO NOT USE automotive oil or boat oil. These
oils will cause eng ine damage. When mixing
fuel, follow instructions printed on container.
Once oil is added to gasoline, shake container
momentarily toassure that the fuel is thorough­ly mixed. Always read and follow the safety
rules relating to fuel before fueling your unit.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri­cation. Lubrication is provided by the auto­matic oiler system when the oil tank is kept
filled.Lack of oil will quickly ruin the bar and
chain. Too little oil will cause overheating
shownby smokecomingfromthechain and/
or discoloration of the bar.

Infreezingweather oil will thicken, making it
necessary to thin bar and chain oil with a
small amount (5to10%) of #1 Diesel Fuel or
kerosene. Bar and chain oil must be free
flowing for the oil system to pump enoughoil
for adequate lubrication.

GenuinePoulanRbarandchain oil isrecom­mended to protect your unit against exces­sive wear from heat and friction. Poulan
oil resists high temperaturethinning. If Pou-

lanRbarand chain oil is not available, use a

good grade SAE 30 oil.

Neverusewasteoilforbarand chainlubri-

S

cation.
Always stop the engine before removing

S

the oil cap.

IMPORTANT

Experience indicates that alcohol--blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads
to separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. To
avoid engine problems, the fuel system
should be emptied before storage for 30
days or longer. Drain the gas tank, start the
engine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel next
season. See STORAGE section for addi­tional information.

Removefuelcapslowly

WARNING:

move whenthe engine runs at idle speed. If
the chain moves at idle speed refer to CAR­BURETOR ADJUSTMENT within this
manual. Avoid contact with themuffler.A hot
muffler can cause serious burns.
To stop the engine move the ON/STOP
switch to the STOP position.
To start the enginehold the saw firmly on
the ground as illustrated. Make sure the
chain is free to turn without contacting any
object.

Use only 15”--18” of rope per pull.
Hold saw firmly while pulling starterrope.

Starter rope handle

Right foot through rear handle

IMPORTANTPOINTS TO REMEMBER

Whenpulling thestarterrope, do not use the
full extent of the rope as this can cause the
rope to break. Do not let starter rope snap
back. Hold the handle and let the rope re­wind slowly.

Do not attempt to cut material with

NOTE:

thefastidlelockbuttoninthelockedposition.

The chain must not

STARTING A COLD ENGINE (or
warm engine after running out of
fuel)

R

1. Move ON/STOP switch to the ON posi-

2. Pull choke knob out to the full extent.

3. Slowly press primer bulb 6 times.

4. Squeeze and hold throttle trigger. With

Throttle
lock--out

Throttle
trigger

5. Sharply pull the starter rope handle 5

ON/STOP SWITCH

(SIDE VIEW)

tion.

thumbpress fast idle lock down;thenre­lease throttle trigger.

Fast idle lock button

times with your right hand. Then, pro­ceed to the next step.

Left hand
on front
handle

ON

STOP

Choke knob

9

NOTE:

ing to start beforethe 5th pull, stop pulling
and immediately proceed to the next step.

6. Push the choke knob in completely (to

If the engine sounds as if it is try-

the OFF position); pull the starter rope
until the engine starts.

CHOKE

(SIDE VIEW)

back toward the front handle as far as
possible.
Whencuttingwiththe saw,the chainbrake

S

must be disengaged.

Disengaged

Engaged

Choke knob

7. Allowthe enginetorunfor approximately
5 seconds. Then, squeeze and release
throttletriggerto allow engineto returnto
idle speed.

OFF FULL

STARTING A WARMENGINE:

1. Move ON/STOP switch to the ON posi­tion.

2. Push the choke knob in completely (to
the OFF position).

3. Slowly press primer bulb 6 times.

4. Squeeze and hold throttle trigger. With
thumbpress fast idlelock down;thenre­lease throttle trigger.

5. Sharply pull the starter rope with your
right hand until the engine starts.

6. Squeeze and release throttle trigger to
allow engine to return to idle speed.

DIFFICULT STARTING (or starting a
flooded engine):

The engine may be flooded with too much
fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ON/
STOPswitch is in the ON position.
Startingcouldrequirepullingthe starterrope
handle many times depending on how badly
theunitisflooded.If enginefailstostart,refer
to the TROUBLESHOOTINGTABLEor call
1-800-554-6723.

CHAIN BRAKE

WARNING:

worn too thin it may break when the chain
brakeis triggered.Witha brokenbrakeband,
the chain brake will not stop the chain. The
chainbrakeshouldbereplacedby anautho­rizedservice dealer if any part is worntoless
than 0.020! (0.5 mm) thick. Repairs on a
chain brake should be made by an autho­rized service dealer. Take your unit to the
place of purchase if purchased from a ser­vicing dealer, or to the nearest authorized
master service dealer.

This saw is equipped with a chain brake.

S

The brake is designed to stop the chain if
kickback occurs.
The inertia--activated chain brake is

S

activated if thefront hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
If the brake is already activated, it is

S

disengagedby pulling thefronthandguard

If the brake band is

Braking function control
CAUTION:

checked several times daily. The engine
mustberunning whenperformingthis proce­dure. This is theonly instancewhenthesaw
should be placed on the ground with the en­gine running.
Place the saw on firm ground. Grip the rear
handlewith yourrighthandandthefronthan­dle with your left hand. Apply full throttleby
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.

The chain brake must be

Inertia activating function control

WARNING:

following procedure, the engine must be
turned off.
Grip therear handlewith your right hand and
thefronthandlewith your left hand. Holdthe
chain saw approximately 14! (35 cm) above
a stump or other wooden surface. Release
your grip on the front handle and use the
weight of the saw to let the top of the guide
bar fall forward and contact the stump.
When the tip of the bar hits the stump, the
brake should activate.

When performing the

CUTTING METHODS

IMPORTANT POINTS

Check chain tension before first use and

S

after 1 minute of operation. See CHAIN
TENSION in the ASSEMBLY section.
Cut wood only. Do not cut metal, plastics,

S

masonry, non-wood building materials, etc.
Stop the saw if the chain strikes a foreign

S

object. Inspect the saw and repair or re­place parts as necessary.
Keep the chain out of dirt and sand. Even a

S

small amount of dirt will quickly dull a chain
andthusincreasethepossibilit yofkickback.
Practice cutting afew small logs using the

S

following techniques to get the “feel” of us­ing your saw before you begin a major
sawing operation.

Squeeze the throttle trigger and allow

S

the engine to reach full speed before
cutting.
Begin cutting with the saw frame

S

against the log.
Keep the engine at full speed the en-

S

tire time you are cutting.

10

Allow the chain to cut for you. Exert

S

only light downward pressure. If you
force the cut, damage to the bar,
chain, or engine can result.
Releasethethrottle triggeras soonas

S

the cut is completed, allowing the en­gine to idle. If you run the saw at full
throttle without a cutting load, unnec­essary wear can occur to the chain,
bar,and engine.
To avoid losing control when cut is

S

complete, do not putpressure on saw
at end of cut.

Stop the engine before setting the saw

S

down after cutting.

TREE FELLING TECHNIQUES

WARNING:

dead branches which can fall while cutting
causingserious injury. Donotcutnearbuild­ingsorelectrical wires if you do not know the
directionoftreefall,norcut atnightsinceyou
will not be ale to see well, nor during bad
weathersuch as rain, snow, orstrongwinds,
etc. If thetreemakes contactwithanyutility
line, the utility company should be notified
immediately.

Carefullyplanyour sawing operationinad-

S

vance.
Clearthe workarea. Youneeda clear area

S

all aroundthe tree so you can have secure
footing.
The chain saw operator should keep on

S

the uphill side of the terrain as the tree is
likely torollorslidedownhill afteritisfelled.
Study the natural conditions that can cause

S

thetreetofallinaparticulardirection.
Natural conditions that can cause a tree to
fall in a particular direction include:

The wind direction and speed.

S

The lean of the tree. The lean of a tree

S

might not be apparent due to uneven or

sloping terrain. Usea plumb orlevel to de-

termine the direction of tree lean.

Weight and branches on one side.

S

Surrounding trees and obstacles.

S

Look for decay and rot. If thetrunk is rotted,
it can snap and fall toward the operator.
Check for broken or dead branches which
can fall on you while cutting.
Make sure there is enough room for the tree to
fall. Maintain a distance of
from the nearest person or other objects. En­gine noise can drown out a warning call.
Remove dirt, stones, loose bark, nails, sta­ples,andwirefromthe treewherecuts areto
be made.
Plana clearretreatpathto the rear anddiag­onal to the line of fall.

45

_

Check for broken or

tree lengths

2-1/2

Plan a clear retreat path

Direction of Fall

FELLING LARGE TREES

(6 inches in diameter or larger)
The notch method is used to fell large trees.
Anotchis cutonthe side ofthetreeinthede­sired direction of fall. After a felling cut is
made on the opposite side of tree, the tree
will tend to fall into thenotch.

If the tree has large buttress roots,

NOTE:

removethembeforemaking thenotch. Ifus­ing saw to remove buttress roots, keep saw
chainfromcontactinggroundto preventdull­ing of the chain.

NOTCH CUT AND FELLING THE
TREE

Make notch cut by cutting the top of the

S

notch first. Cut through
ofthetree. Nextcompletethenotch bycut­ting the bottom of the notch. See illustra­tion. Once the notch is cut remove the
notch of wood from the tree.

Final (felling) cut here. 2 in­ches above center of notch.

First cut

Notch

Second cut

After removing the wood from the notch,

S

makethefelling cut on theopposite sideof
the notch. This is done by making a cut
abouttwo inches higher thanthe center of
the notch. This will leave enough uncut
woodbetween the fellingcutandthenotch
to form a hinge. This hinge will help pre­ventthetreefromfallingin thewrongdirec­tion.

Hinge holds tree on stump and helps
control fall

Closing of
notch

NOTE:

wedges to open the cut if necessary to
controlthedirectionoffall. T oavoidkickback
and chain damage, use wood or plastic
wedges, but never steel or iron wedges.

S

Beforefelling cut is complete, use

Be alert to signs that the tree is ready to
fall: cracking sounds, widening of the fell­ing cut, or movement in the upper
branches.

of the diameter

1/3

Hinge

Opening
of felling
cut

11

As tree starts to fall, stop saw,put it down,

S

and get away quickly on your planned re-

treat path.

DO NOT cut down a partially fallen tree

S

withyour saw. Be extremely cautious with

partially fallen trees that may be poorly

supported. When a tree doesn’t fall com-

pletely,setthesawasideandpull downthe

tree with a cable winch, block and tackle,

or tractor.

CUTTINGA FALLENTREE

(BUCKING)

Bucking is the term used for cutting a fallen
tree to the desired log size.

Undercuttinginvolves cuttingontheunder­side ofthelog with top ofsaw againstthelog.
When undercutting use light upward pres­sure. Hold saw firmly and maintain control.
The saw will tendto push back toward you.

WARNING:

down to undercut. The saw cannot be con­trolled in this position.
Always make your first cut on the compres­sion side ofthelog. Thecompression sideof
the log is where the pressure of the log’s
weight is concentrated.

First cut on compression side of log

Never turn saw upside

WARNING:

being cut. Any portion can roll causing loss
of footing and control. Do not stand downhill
of the log being cut.

Donot stand on the log

IMPORTANT POINTS

Cut only one log at a time.

S

Cut shattered wood very carefully; sharp

S

piecesofwoodcouldbe flung towardoper-

ator.

Use a sawhorse to cut small logs. Never

S

allow another person to hold the log while

cuttingandnever hold thelogwith your leg

or foot.

Do not cut in an area where logs, limbs,

S

and roots are tangled such as in a blown

downarea. Dragthelogs into a clear area

beforecutting by pulling out exposedand

cleared logs first.

TYPES OF CUTTING USED FOR
BUCKING

WARNING:

pinched or hung in a log, don’t try to force it
out. Youcanlosecontrolofthesawresulting
in injury and/ordamage to the saw. Stop the
saw,drive awedgeofplastic orwoodinto the
cutuntil thesaw canberemoved easily. Re­startthesawandcarefully reenterthecut. To
avoid kickback and chain damage, do not
usea metal wedge. Donot attempt torestart
your saw when it is pinched or hung in a log.

Use a wedge to remove pinchedsaw

If saw becomes

Second cut

Second cut

First cut on compression side of log

BUCKINGWITHOUTA SUPPORT

Overcut through

S

log.
Roll the log over and finish with a second

S

overcut.
Watch for logs with a compression side to

S

prevent the saw from pinching. See il­lustrations for cutting logs withacompres­sion side.

of the diameter of the

1/3

BUCKINGUSING A LOG OR
SUPPORT STAND

Remember your first cut is always on the

S

compression side of the log.
(Refer to the illustrations below for your
first and second cut)
Y our first cut should extend

S

diameter of the log.
Finish with your second cut.

S

Using a log for support

nd

2

Cut

1/3

of the

Turn saw OFF and use a plastic or
wooden wedge to force cut open.

Overcuttingbegins onthetopsideof thelog
with the bottom of the saw against the log.
When overcutting use light downward pres­sure.

Overcutting

Undercutting

12

2ndCut

1stCut

st

1

Cut

Using a support stand

nd

2

Cut

1stCut

1stCut

PRUNING

WARNING:

shoulder height or below . Do not cut if
branchesare higher than your shoulder.Get
a professional to do the job.

Make your first cut

S

through the bottom of the limb.
Next make a 2nd cut all the way

S

through the limb. Then cut a third
overcut leaving a 1 to 2 inch collar
from the truck of the tree.

Limit pruning to limbs

of the way

1/3

nd

Cut

2

LIMBINGAND PRUNING

WARNING:

against kickback. Do not allow the moving
chain to contact any other branches or ob­jects at the nose of theguide bar when limb­ingorpruning. Allowing such contact canre­sult in serious injury.

WARNING:

to limb or prune. Do not stand on ladders,
platforms, a log, or in any position which can
cause you to lose your balance or control of
the saw.

IMPORTANT POINTS

Work slowly, keeping both hands firmly

S

gripped on the saw. Maintain secure foot-

ing and balance.

Watch out for springpoles. Springpoles are

S

small size limbs which can catch the saw

chain and whip toward youor pull you off bal-

ance. Use extreme caution when cutting

small size limbs or slender material.

Be alert for springback. Watch out for

S

branches that are bent or underpressure.

Avoid being struck by the branch or the

saw when the tension in the woodfibers is

released.

Keep a clear work area. Frequentlyclear

S

branches out of the way to avoid tripping

over them.

LIMBING

Alwayslimbatreeafteritis cutdown. Only

S

thencan limbing be donesafely and prop-

erly.

Leave the larger limbs underneath the

S

felled tree to support the treeas you work.

Startat the baseofthefelled tree andwork

S

toward the top, cutting branches and

limbs. Removesmall limbs with one cut.

Keep the tree betweenyou and the chain.

S

Cut from the side of the tree opposite the

branch you are cutting.

Remove larger, supporting branches with

S

thecuttingtechniquesdescribedin BUCK-

ING WITHOUT A SUPPORT.

Always use an overcut to cut small and

S

freely hanging limbs. Undercutting could

cause limbs to fall and pinch the saw.

Be alert for and guard

Never climb into a tree

Third cut

Collar

Second cut

First cut

Pruning technique

SERVICE

WARNING:

plug beforeperforming maintenanceexcept
for carburetor adjustments.
We recommend all service and adjustments
not listed in this manual be performed by an
authorized or Master Service Dealer.

MAINTENANCE SCHEDULE

Check:

Fuel mixture level Before each use....

Bar lubrication Before each use.......

Chain tension Before each use.......

Chain sharpness Before each use....

For damaged parts Before each use..

For loose caps Before each use......

For loose fasteners Before each use...

For loose parts Before each use......

Inspect and Clean:

Bar Before each use................

Complete saw After each use.......

Air filter Every 5 hours*.............

Chain brake Every 5 hours*........

Spark arresting screen

and muffler Every 25 hours*.........

Replace spark plug
Replace fuel filter

* Hour s of Operation

AIR FILTER
CAUTION

or other flammable solvent to avoid creating
a fire hazard or producing harmful evapora­tive emissions.

Cleaning the air filter:

A dirty air filter decreases engine perform­ance and increases fuel consumption and
harmful emissions. Always clean after 15
tanks of fuel or 5 hours of operation, which­ever comes first. Clean more frequently in

: Donot clean filter in gasoline

13

Disconnect the spark

Yea r l y.
Yea r l y...

dustyconditions. Aused aire filter can never
becompletely cleaned. Itis advisable to re­placeyourairfilterwitha newoneafterevery
50hoursofoperation,or annually,whichever
comes first.

1. Loosen3 screws on cylinder cover.

2. Remove cylinder cover.

3. Remove air filter.

4. Cleanthe air filter using hot soapy water.

Rinsewith cleancool water. Airdrycom­pletely before reinstalling.

5. Lightly oil air filter beforeinstalling to im-

prove the efficiency of air filter. Use
2--cycle engine oil or motoroil (SAE30).
Squeeze excess oil from filter.

6. Reinstall air filter.

7. Reinstall cylinder cover and 3 screws.

TIghten securely.

Air Filter

Cylinder Cover
Screws

Cylinder
Cover

INSPECT MUFFLER AND SPARK
ARRESTINGSCREEN

As the unit is used, carbondeposits build up
on the muffler and spark arresting screen,
andmust be removedto avoid creatinga fire
hazard or affecting engine performance.
Replacethesparkarresting screen if breaks
occur.

Muffler
Body

Muffler
Cover

MufflerDiffuser

Spark
Arresting
Screen

Muffler
Cover
Screws

CLEANING THE SPARK ARREST­ING SCREEN

Cleaning is required every 25 hours of op­eration or annually, whichever comes first.

1. Loosen and remove the 2 muffler cover

screws.

2. Remove the muffler cover (cover snaps

off muffler body).

3. Remove muffler diffuser and spark ar-

resting screen assembly. Notice the
orientation of these parts for reassem­bling.

4. Clean the spark arresting screen with a

wire brush. Replace screenif breaksare
found.

5. Replace any broken or cracked muffler

parts.

6. Reinstall diffu ser and sp a r k arrest ing
screen assembly with roun d holes facing
up.

7. Reinstall muffler cover and 2 screws.
Tighten securely.

CARBURETOR ADJUSTMENT

WARNING:

ing during most of this procedure.Wearyour
protective equipmentand observe all safety
precautions.Thechain mustnotmove atidle
speed.
The carburetor has beencarefully set at the
factory. Adjustments may be necessary if
you notice any of the following conditions:

Chain moves at idle. See IDLE SPEED--T

S

adjusting procedure.
Sawwill not idle. See IDLESPEED--T ad-

S

justing procedure.

Idle Speed--T

Allow engine to idle. If the chain moves, idle
istoofast. Iftheenginestalls, idle is too slow.
Adjust speed until engineruns withoutchain
movement (idle too fast) or stalling (idle too
slow). Theidle speed screw islocated in the
area above the primer bulb and is labeled T.

Turnidle speedscrew (T) clockwise to in-

S

crease engine speed.
Turn idle speed screw (T) counterclock-

S

wise to decrease engine speed.
If you require further assistance or are unsure
about performing this procedure, contact your
authorized service dealer or call
1- -800--554--6723.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced
throughthecut,orbeen runwithanimproper
amount of bar lubrication it may be neces­sarytoserviceyourbar. A wornbarwilldam­age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is
in the STOP position, thenclean all sawdust
from the guide bar and sprocket hole.

To maintain guide bar:

MoveON/STOPswitch to the STOP posi-

S

tion.

Loosen and remove chain brake nuts and

S

chain brake. Remove bar and chain from

saw.

Clean the oil holes and bar groove after

S

each 5 hours of operation.

RemoveSawdustFrom

Guide Bar Groove

Burring of guide bar rails is a normal

S

process of rail wear. Remove these burrs

with a flat file.

Whenrail topisuneven,use a flat file to re-

S

store square edges and sides.

The chain will be mov-

Oil Holes

14

File Rail Edges

and Sides

Square

Replace guide bar when thegroove is worn,
the guide bar is bent or cracked, or when
excess heating or burring of the rails occurs.
If replacement is necessary, use only the
guidebarspecified for yoursaw in the repair
partslist or onthedecal locatedonthechain
saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that
requires special tools. We recommended
you refer chain sharpeningto a professional
chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each
year to ensure the engine starts easier and
runs better.

1. Loosen3 screws on cylinder cover.

2. Remove the cylinder cover.

3. Pull off the spark plug boot.

4. Remove spark plug from cylinder and
discard.

5. Replace with Champion RCJ--7Y spark
plug and tighten securely with a 3/4inch
socket wrench. Spark plug gap should
be 0.025 inches.

6. Reinstall the spark plug boot.

7. Reinstall the cylinder cover and 3
screws. Tighten securely.

Screws

Spark

Plug Boot

CorrectGrooveWorn Groove

Cylinder

Cover

STORAGE

WARNING:

to cool, and secure the unit beforestoring or
transporting in a vehicle. Store unit and fuel
in an area where fuel vapors cannot reach
sparks or open flames from water heaters,
electric motors or switches, furnaces, etc.
Storeunitwithall guardsin place. Position so
that any sharp object cannot accidentally
cause injury to passersby. Store the unit out
of reach of children.

Before storing, drain all fuel from the unit.

S

Start engine and allow to run until it stops.
Clean the unit before storing. Pay particu-

S

lar attention to the air intake area,keeping
it free of debris. Use a mild detergentand
sponge to clean the plastic surfaces.
Donotstorethe unit orfuel in a closed area

S

where fuel vapors can reach sparks or an
openflamefromhot waterheaters,electric
motors or switches, furnaces, etc.
Store in a dry areaoutof the reach ofchil-

S

dren.

CAUTION

dep osits from forming in essential fuel system
parts such as the carburetor , fuel filter, fuel
hose, or fuel tank during storage. Alcohol
blended fuels (called gasohol or using ethanol
or methanol) can attract moisture which leads
to fuel mixture separation and formation of
acids during storage. Acidic gas can damage
the engine.

: It is important to prevent gum

Stop engine and allow

Spark

Plug

15

TROUBLESH

O

O

WARNING:

therecommendedremediesbelow exceptremedies thatrequire operationof theunit.

TINGTABLE

Always stop unit and disconnect spark plug before performing all of

TROUBLE CAUSE REMEDY

Enginewill not
start or will run
only a few
seconds after
starting.

Enginewill
notidle
properly.

Enginewill not
accelerate,
lacks power,
or dies under
a load.

Engine
smokes
excessively.

Chain moves
at idle speed.

1. Ignition switch off.

2. Engine flooded.

3. Fuel tank empty.

4. Spark plug not firing.

5. Fuel not reaching
carburetor.

1. Idle speed requires
adjustment.

2. Carburetor requires
adjustment.

1. Air filter dirty.

2. Spark plug fouled.

3. Chain brake engaged.

4. Carburetor requires
adjustment.

1. Too much oil mixed with
gasoline.

1. Idle speed requires
adjustment.

2. Clutch requires repair.

1. Move ignition switch to ON.

2. See “Difficult Starting” in
Operation Section.

3. Fill tank with correct fuel mixture.

4. Install new spark plug.

5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.

1. See “Carburetor Adjustment” in the
Service and Adjustments Section.

2. Contact an authorized service dealer.

1. Clean or replace air filter.

2. Clean or replace plug and regap.

3. Disengage chain brake.

4. Contact an authorized service dealer.

1. Empty fuel tank and refill with
correct fuel mixture.

1. See “Carburetor Adjustment” in the
Service and Adjustments Section.

2. Contact an authorized service dealer.

16

NEED ASSISTANCE?

NEED ASSISTANCE?

Call 1---800---554---6723.

NEED SERVICE PART?

Contact your dealer or place of purchase.

LIMITED WARRANTY

ELECTROLUXHOME PRODUCTS, INC.,

warrants to the original purchaser that each
new Poulan
free from defects in material and workman­ship and agrees to repair or replace under
this warranty any defective gasoline chain
saw as follows from the original date of pur­chase.
1 YEAR -- Parts and Labor,when used for
Household purposes.
60 DAYS -- Parts and Labor, when used for
Commercial, Professional, or Income Pro­ducing purposes.
30DAYS-- Parts andLabor,if used forrental
purposes.
This warranty is not transferable and does
not cover damage or liability caused by im­proper handling, improper maintenance, or
the use of accessories and/or attachments
not specifically recommended by ELEC-
TROLUXHOMEPRODUCTS,INC.,for this
chain saw. Additionally, this warranty does
not cover damagecaused by improper han­dling, improper maintenance,or if the saw is
alteredin any waywhichinourjudgementaf-

brand gasoline chain saw is

RRRR

U.S. EPA / ENVIRONMENT CANADA

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OB­LIGATIONS: The U. S. Environmental

Protection Agency, Environment Canada
and ELECTROLUX HOME PRODUCTS,
INC., are pleased to explain the emissions
control system warranty on your year
2002--2004 small off--road engine. ELEC­TROLUX HOME PRODUCTS, INC., must
warranttheemission controlsystem onyour
small off--road enginefor the periods of time
listed below provided there has been no
abuse, neglect, or improper maintenance of
your small off--road engine. Your emission
control system includes parts such as the
carburetorand the ignition system. Where a
warrantable condition exists, ELECTRO­LUX HOME PRODUCTS, INC., will repair
your small off--road engine at no cost to you.
Expenses covered under warranty include
diagnosis, partsandlabor. MANUFACTUR-
ER’S WARRANTY COVERAGE: If any
emissions related part on your engine (as
listed under Emissions Control Warranty
Parts List) is defective or a defect in thema­terials or workmanship of the engine causes
the failure of such an emission related part,
the part will be repaired or replaced by
ELECTROLUX HOME PRODUCTS, INC.

OWNER’S WARRANTY RESPONSIBILI­TIES: As the small off--road engine owner ,

fectsitsconditionoroperation.This warranty
does not cover tune--up, spark plugs, filters,
starterropes,startersprings,chainsharpen­ing,bars,chains,andotherpartswhichwear
and require replacement with reasonable
use duringthewarrantyperiod.This warran­ty does not cover predelivery set--up,instal­lation of guide bar and chain, and normal ad­justments explained in the instruction
manual such as carburetoradjustments and
chain tension adjustments. This warranty
does not cover transportation costs.

THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX­PRESSLYSTIPULATEDHEREIN.

SOME STATES DO NOT ALLOW LIMITA­TIONSON HOW LONGANIMPLIEDWAR­RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON­SEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSION
MAY NOT APPLYTO YOU.
The policy of ELECTROLUXHOME PRO-
DUCTS,INC.,is to continuously improveits
products.Therefore,ELECTROLUXHOME
PRODUCTS, INC., reserves the right to
change, modify, or discontinue models, de­signs, specifications, and accessories of all
productsatany time withoutnotice or obliga­tion to any purchaser.

you are responsible for the performance of
the required maintenance listed in your in­struction manual. ELECTROLUX HOME
PRODUCTS, INC., recommends that you
retain all receipts covering maintenance on
your small off--road engine, but ELECTRO­LUX HOME PRODUCTS, INC., cannot
deny warranty solely for the lack of receipts
orfor your failure toensure the performance
ofall scheduledmaintenance. As thesmall
off--road engine owner,you shouldbeaware
that ELECTROLUX HOME PRODUCTS,
INC., may deny you warranty coverage if
your small off--road engine or a part of it has
failed due to abuse, neglect, impropermain­tenance, unapproved modifications, or the
use of parts not made or approved by the
original equipment manufacturer. You are
responsible for presenting your small off-­road engine to an ELECTROLUX HOME
PRODUCTS,INC.,authorizedrepair center
as soon as a problem exists. Warranty re­pairs should be completed in a reasonable
amountof time, notto exceed 30days. Ifyou
haveany questions regardingyour warranty
rights and responsibilities, you should con­tact your nearest authorized service center
or call ELECTROLUXHOME PRODUCTS,
INC., at 1--800--554--6723. WARRANTY
COMMENCEMENT DATE: The warranty

17

period begins on the date the small off--road
engineis purchased. LENGTHOF COVER-
AGE: This warranty shall be for a period of
two years from the initial date of purchase.

WHAT IS COVERED: REPAIR OR RE­PLACEMENT OF PARTS. Repair or re-

placementof any warrantedpart will be per­formed at no charge to the owner at an
approved ELECTROLUX HOME PROD­UCTS, INC., servicing center. If you have
any questions regarding your warranty
rights and responsibilities, you should con­tact your nearest authorized service center
orcall ELECTROLUX HOME PRODUCTS,
INC., at 1--800--554--6723. WARRANTY
PERIOD: Any warranted part which is not
scheduled for replacement as required
maintenance, or which is scheduled only for
regular inspection to the effect of “repair or
replaceasnecessary”shall be warrantedfor
2years. Any warrantedpartwhich is sched­uled for replacement as required mainte­nance shall be warranted for the period of
time up to the first scheduled replacement
point for that part. DIAGNOSIS: The owner
shall not be charged for diagnostic labor
which leads to the determinationthat a war­rantedpartis defective if thediagnosticwork
is performedat an approved ELECTROLUX
HOMEPRODUCTS,INC., servicing center.
CONSEQUENTIAL DAMAGES: ELEC­TROLUX HOME PRODUCTS, INC., may
be liable for damages to other engine com­ponentscaused by the failureof a warranted

The information on the product label indicates which standard your engine is certified.
Example: (Year)EPAPhase 1 or Phase 2 and/or CALIFORNIA.

part still under warranty. WHAT IS NOT
COVERED: All failures caused by abuse,
neglect, or improper maintenance are not
covered.ADD--ON OR MODIFIEDPARTS:
The use of add--on or modified parts can be
grounds for disallowing a warranty claim.
ELECTROLUX HOME PRODUCTS, INC.,
is not liable to cover failures of warranted
parts caused by the use of add--on or modi­fied parts. HOW TO FILE A CLAIM: If you
haveany questions regardingyour warranty
rights and responsibilities, you should con­tact your nearest authorized service center
or call ELECTROLUXHOME PRODUCTS,
INC.,at1--800--554--6723.WHERE TOGET
WARRANTYSERVICE: Warranty services
orrepairsshall beprovidedatall ELECTRO­LUX HOME PRODUCTS, INC., service
centers. Call 1--800--554--6723. MAINTE-

NANCE, REPLACEMENT AND REPAIR
OF EMISSION RELATED PARTS: Any

ELECTROLUX HOME PRODUCTS, INC.,
approved replacement part used in the per­formance of any warranty maintenance or
repair on emission related parts will be pro­vided withoutcharge to the owner if the part
is under warranty. EMISSION CONTROL
WARRANTY PARTS LIST: Carburetor,
Ignition System: Spark Plug (covered up to
maintenance schedule), Ignition Module.
MAINTENANCE STATEMENT: The owner
is responsible for the performance of all re­quired maintenance as defined in the in­struction manual.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)

18