Poulan Pro 1999-12, 3750 Operator's Manual

Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.

1-800-554-6723

www.poulan.com

Operator’s Manual

Manual del Operador

ENGLISH

Manuel de L’utilisateur

3450
3750

U

L

R

WARNING:

Read and follow all Safety Rules and Operating Instructions before using this
product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual del operador y siga todas las advertencias e enstrucciones de
seguridad. El no hacerlo puede resultar en lesiones graves.

ESPAÑOL

Frigidaire Home Products, Augusta, GA 30907

WCI Outdoor Products, Inc.

530087292 12

/07/99

SAFETY RULES

WARNING:

plug wire and place wire where it cannot
contact spark plug to prevent accidental
starting when setting up, transporting, ad­justing or making repairs except carburetor
adjustments.

Because a chain saw is a high-speed wood­cutting tool, special safety precautions must
be observed to reduce the risk of accidents.
Careless or improper use of this tool can
cause serious injury.

PLAN AHEAD

S

Read this manual carefully until you com­pletely understand and can follow all safe­ty rules, precautions, and operating in ­structions before attempting to use the
unit.

S

Restrict the use of your saw to adult users
who understand and can follow safety
rules, precautions, and operating instruc­tions found in this manual.

Hearing

Protection

Snug
Fitting

Clothing

S

Wear protective gear. Always use steel­toed safety footwear with non-slip soles;
snug-fitting clothing; heavy-duty, non-slip
gloves; eye protection such as non-fog­ging, vented goggles or face screen; an
approved safety hard hat; and sound bar­riers ( ear plugs or mufflers) to protect your
hearing. Regular users should have hear­ing checked regularly as chain saw noise
can damage hearing. Secure hair above
shoulder length.

S

Keep all parts of your body away from the
chain when the engine is running.

S

Keep children, bystanders, and animals a
minimum of 30 feet (10 Meters) away from
the work area. Do not allow other people
or animals to be near the chain saw when
starting or operating the chain saw.

S

Do not handle or operate a chain saw
when you are fatigued, ill, or upset, or if
you have taken alcohol, drugs, or
medication. You must be in good physical
condition and mentally alert. Chain saw
work is strenuous. If you have any condi­tion that might be aggravated by strenu­ous work, check with your doctor before
operating a chain saw.

Always disconnect spark

Safety Hat

Safety
Shoes

Safety Chaps

Eye
Protection

Heavy Duty
Gloves

S

Carefully plan your sawing operation in
advance. Do not start cutting until you
have a clear work area, secure footing,
and, if you are felling trees, a planned re­treat path.

OPERATE YOUR SAW SAFELY

S

Do not operate a chain saw with one
hand. Serious injury to the operator, help­ers, bystanders or any combination of
these persons may result from one­handed operation. A chain saw is in­tended for two-handed use.

S

Operate the chain saw only in a well-venti­lated outdoor area.

S

Do not operate saw from a ladder or in a
tree, unless you are specifically trained to
do so.

S

Make sure the chain will not make contact
with any object while starting the engine.
Never try to start the saw when the guide
bar is in a cut.

S

Do not put pressure on the saw at the end
of the cut. Applying pressure can cause
you to lose control when the cut is com­pleted.

S

Stop the engine before setting the saw
down.

S

Be alert for springback when cutting a
limb that is under tension so you will not
be struck by the limb or saw when the ten­sion in the wood fibers is released.

MAINTAIN YOUR SAW IN GOOD
WORKING ORDER

S

Have all chain saw service performed by a
qualified service dealer with the exception
of the items listed in the maintenance sec­tion of this manual. For example, if im­proper tools are used to remove or hold
the flywheel when servicing the clutch,
structural damage to the flywheel can oc­cur and cause the flywheel to burst.

S

Make certain the saw chain stops moving
when the throttle trigger is released. For
correction, refer to “Carburetor Adjust­ments.”

S

Never modify your saw in any way. Use
only attachments supplied or specifically
recommended by the manufacturer.

S

Keep the handles dry, clean, and free of
oil or fuel mixture.

S

With the engine stopped, hand carry the
chain saw with the muffler away from your
body, and the guide bar and chain to the
rear, preferably covered with a scabbard.

S

Keep fuel and oil caps, screws, and fas­teners securely tightened.

S

Use only Poulan or Poulan Pro accesso­ries and replacement parts as recom­mended.

HANDLE FUEL WITH CAUTION

S

Do not smoke while handling fuel or while
operating the saw.

S

Eliminate all sources of sparks or flame in
the areas where fuel is mixed or poured.
There should be no smoking, open
flames, or work that could cause sparks.
Allow engine to cool before refueling.

S

Mix and pour fuel in an outdoor area on
bare ground; store fuel in a cool, dry, well

2

ventilated place; and use an approved,
marked container for all fuel purposes.
Wipe up all fuel spills before starting saw.

S

Move at least 10 feet (3 meters) from fuel­ing site before starting engine.

S

Turn the engine off and let saw cool in a
non-combustible area, not on dry leaves,
straw, paper, etc. Slowly remove fuel cap
and refuel unit.

S

Store the unit and fuel in an area where
fuel vapors cannot reach sparks or open
flames from water heaters, electric motors
or switches, furnaces, etc.

KICKBACK
WARNING:

the moving chain contacts an object at the
upper portion of the tip of the guide bar or
when the wood closes in and pinches the
saw chain in the cut. Contact at the upper
portion of the tip of the guide bar can cause
the chain to dig into the object, which stops
the chain for an instant. The result is a light­ning fast, reverse reaction which kicks the
guide bar up and back toward the operator.
If the saw chain is pinched along the top of
the guide bar, the guide bar can be driven
rapidly back toward the operator. Either of
these reactions can cause loss of saw con­trol which can result in serious injury.

against kickback
Rotational Kickback

and backward motion of the chain saw that
can occur when the moving saw chain near
the upper portion of the tip of the guide bar
contacts an object such as a log or a
branch.

Pinch-Kickback and Pull-In occur when the
chain is suddenly stopped by being
pinched, caught, or b y contacting a foreign
object in the wood. This sudden stopping of
the chain results in a reversal of the chain
force used to cut wood and causes the saw
to move in the opposite direction of the
chain rotation. Pinch-Kickback drives the
saw straight back toward the operator. Pull­In pulls the saw away from the operator. Ei­ther reaction can result in loss of control and
serious injury.

Avoid Pinch--- Kickback:

S

Be extremely aware of situations or ob­structions that can cause material to
pinch the top of or otherwise stop the
chain.

S

Do not cut more than one log at a time.

S

Do not twist the saw as the bar is with­drawn from an undercut when bucking.

A v o i d P u l l --- I n :

S

Always begin cutting with engine at full
speed and saw housing against wood.

S

Use wedges made of plastic or wood.
Neverusemetaltoholdthecutopen.

Kickback Path

Kickback can occur when

Guard

is the rapid upward

Clear the work area; avoid obstructions.

REDUCETHECHANCEOF
KICKBACK

S

Recognize that kickback can happen.
With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.

S

Never let the moving chain contact any
object at the tip of the guide bar.

S

Keep the working area free from obstruc­tions such as other trees, branches,
rocks, fences, stumps, etc. Eliminate or
avoid any obstruction that your saw chain
could hit while you are cutting through a
particular log or branch.

S

Keep your saw chain sharp and properly
tensioned. A loose or dull chain can in­crease the chance of kickback occurring.
Follow manufacturer’s chain sharpening
and maintenance instructions. Check
tension at regular intervals with the en­gine stopped, never with engine running.
Make sure the bar clamp nuts are secure­ly tightened after tensioning the chain.

S

Begin and continue cutting at full speed. If
chain is moving at a slower speed, there is
greater chance of kickback occurring.

S

Cutonelogatatime.

S

Use extreme caution when re-entering a
previous cut.

S

Do not attempt cuts starting with the tip of
the bar (plunge cuts).

S

Watch for shifting logs or other forces that
could close a cut and pinch or fall into chain.

S

Use Reduced- Kickback Guide Bar and
Low-Kickback Chain specified for your saw.

MAINTAIN CONTROL

S

Keep a good, firm grip on the saw with both
hands when the engine is running and
don’t let go. A firm grip will help you reduce
kickback and maintain control of the saw.
Keep the fingers of your left hand encircling
and your left thumb under the front handle­bar. Keep your right hand completely
around the rear handle whether your are
right handed or left handed. Keep your left
arm straight with the elbow locked.

Elbow locked

3

Thumb on underside of
handlebar

S

Position your left hand on the front han­dlebar so it is in a straight line with your
right hand on the rear handle when mak­ing bucking cuts. Never reverse right and
left hand positions for any type of cutting.

Stand to the left of
the saw

Never reverse
hand positions

S

Stand with your weight evenly balanced
on both feet.

S

Stand slightly to the left side of the saw to
keep your body from being in a direct line
with the cutting chain.

S

Do not overreach. You could be drawn or
thrown off balance and lose control of saw.

S

Do not cut above shoulder height. It is dif­ficult to maintain control of saw above
shoulder height.

KICKBACK SAFETY FEATURES
WARNING:

included on your saw to help reduce the
hazard of kickback; however, such features
will not totally eliminate this dangerous reac­tion. As a chain saw user, do not rely only on
safety devices. You must follow all safety
precautions, instructions, and maintenance
in this manual to help avoid kickback and
other forces which can result in serious
injury.

S

Reduced-Kickback Guide Bar, designed
with a small radius tip which reduces the
size of the kickback danger zone on bar
tip. A Reduced-Kickback Guide Bar has
been demonstrated to significantly re­duce the number and seriousness of kick­backs when tested in accordance with
safety requirements for gasoline powered
chain saws as set by ANSI B175.1.

Reduced Kickback Symmetrical Guide Bar

Symmetrical Guide Bar

S

Low-Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood to gradually ride into the cutter.
Low-Kickback Chain has met kickback
performance requirements when tested
on a representative sample of chain saws

The following features are

Small Radius Tip

Large Radius Tip

below 3.8 cubic inch displacement speci­fied in ANSI B175.1.

Contoured Depth Gauge

Elongated Guard Link

Deflects Kickback
Force And Allows

Low--Kickback

Chain

Chain With High Kickback Potential

S

Handguard, designed to reduce the
chance of your left hand contacting chain
if your hand slips off the front handlebar.

S

Position of front and rear handlebars, de­signed with distance between handles
and “in-line” with each other. The spread
and “in-line” position of the hands pro­vided by this design work together to give
balance and resistance in controlling the
pivot of the saw back toward the operator
if kickback occurs.

ANSI B175.1-1991

Standard for Powered Tools --- Gasoline
Powered Chain Saw --- Safety Require­ments.”

NOTE

mercial logging, you must order and
install a chain brake to comply with Feder­al OSHA Regulations for Commercial Log­ging. Contact your Authorized Service
Dealer or call 1-800-554-6723.

If this saw is to be used for com-

:

SAFETY NOTICE:

vibrations through prolonged use of
gasoline powered hand tools could cause
blood vessel or nerve damage in the
fingers, hands, and joints of people prone
to circulation disorders or abnormal
swellings. Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools
on a continual and regular basis must
monitor closely their physical condition and
the condition of this tool.

SPECIAL NOTICE:

equipped with a temperature limiting
muffler and spark arresting screen which
meets the requirements of California Codes
4442 and 4443. All
states of California, Idaho, Maine,
Minnesota, New Jersey, Oregon, and
Washington require many internal
combustion engines to be equipped with a
spark arrestor screen by law. If you operate
a chain saw in a state or locale where such

Wood T o Gradually
Ride Into Cutter

Can Obstruct
Material

“Am e r i c a n N at i o n a l

Exposure to

Your s a w is

forest land and the

U.S.

4

regulations exist, you are legally
responsible for maintaining the operating
condition of these parts. Failure to do so is
a violation of the law. Refer to the SERVICE
section for maintenance of the Spark
Arrestor.

Failure to follow all Safety Rules and Precau­tions can result in serious injury. If situations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your Authorized Service
Dealer.

ASSEMBLY

The assembly tool provided with your saw
is the only tool needed for assembly. Pro­tective gloves (not provided) should be
worn during assembly.

ATTACHING THE BAR & CHAIN

(If not already attached)

WARNING:

step if the saw is received assembled. Al­ways wear gloves when handling the chain.
The chain is sharp and can cut you even
when it is not moving!

S

Loosen and remove the clamp nuts and
the bar clamp from the saw.

S

Remove the plastic shipping spacer (if
present).

Assembly
Tool

S

An adjusting pin and screw is used to ad­just the tension of the chain. It is very im­portant when assembling the bar, that the
pin located on the adjusting screw aligns
into a hole in the bar.

Recheck each assembly

Shipping
Spacer

Bar

Clamp

Clamp Nuts

Adjustment
Screw

S

Mount the bar as illustrated.

S

Slide the bar toward the rear of the saw as
far as possible.

S

Prepare the chain by checking the proper
direction. Without following the illustration
it is easy to place the chain on the saw the
wrong direction. Use the illustration of the
chain to determine the proper direction.

Tip of Bar

Proper chain direction

S

Place the chain onto the sprocket located
behind the clutch drum. Fit the chain be­tween the teeth in the sprocket.

S

Start at the top of the bar and fit chain into
groove around the guide bar.

S

After chain is installed, pull bar forward
until chain is snug in the groove of the bar.

S

Hold guide bar against the saw frame
making sure the adjusting pin is aligned
with the hole in the bar. Remember this
pin moves the bar forward and backward
as screw is turned. Install the bar clamp.

S

Replace the bar clamp nuts and tighten
finger tight. Once the chain is tensioned
you will need to tighten bar clamp nuts.

CHAIN TENSION

chain already installed)

NOTE

make sure the bar nuts are finger tight only.
Attempting to tension the chain when the
bar nuts are tight can cause damage.

When adjusting chain tension,

:

(Including units with

Checking the tension:

Use the screwdriver end of the combination
screwdriver/wrench tool to move the chain
around the bar.If the chain does not rotate, it
is too tight. If too loose, the chain will sag be­low the bar.

S

Turn the adjusting screw counterclock­wise to move the adjusting pin almost as
far as it will go to the rear. This should al­low the pin to be near the correct position.
Further adjustment may be necessary as
you mount the bar.

5

Adjusting the tension:

Chain tension is very important. Chain
stretches during use. This is especially true
during the first few times you use your saw.
Always check chain tension each time you
use and refuel your saw.

You can adjust chain tension by loosening
the bar clamp nuts and turning adjusting
screw 1/4 of a turn while lifting up on the bar.

S

If chain is too tight, turn adjusting screw
1/4 turn counterclockwise.

S

If chain is too loose, turn adjusting screw
1/4 turn clockwise.

S

Lift up the tip of the bar and tighten the bar
clamp nuts with the assembly tool.

S

Recheck chain tension. Tension is correct
when chain does not sag below the bar
but still can be moved around the bar.

Genuine
chain oil is recommended to protect your
unit against excessive wear from heat and
friction.
high temperature thinning. If

POULAN PRO

available, use a good grade SAE 30 oil.

S

S

POULAN

POULANorPOULAN PRO

Never use waste oil for bar and chain lu­brication.
Always stop the engine before removing
the oil cap.

Oil Cap

POULAN PRO

or

bar and chain oil is not

bar and

oil resists

POULAN

Fuel mix cap

or

STARTING

Lifts only 1/8 of an inch from bar.

Adjusting

Screw

FUELING & LUBRICATION

FUELING ENGINE

This engine is certified to operate on
unleaded gasoline. Before operation,
gasoline must be mixed with a good quality
2-cycle air-cooled engine oil. We
recommend Poulan/W eed Eater brand oil. If
you do not use this oil, use a good quality
2-cycle air-cooled oil designed to be mixed at
a ratio of 40:1 (A 40:1 ratio is obtained by
mixing 3.2 onces of oil with 1 gallon of
unleaded gasoline). When mixing fuel follow
the instructions printed on the container.
Always read and follow the safety rules
relating to fuel before fueling your unit.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lu­brication. Lubrication is provided by the au­tomatic oiler system when the oil tank is kept
filled. Lack of oil will quickly ruin the bar and
chain. Too little oil will cause overheating
shown by smoke coming from the chain
and/or discoloration of the bar.

In freezing weather oil will thicken, making it
necessary to thin bar and chain oil with a
small amount (5 to 10%) of #1 Diesel Fuel or
kerosene. Bar and chain oil must be free
flowing for the oil system to pump enough
oil for adequate lubrication.

WARNING:

when the engine runs at idle speed. If the
chain moves at idle speed refer to

TOR ADJUSTMENT

contact with the muffler. A hot muffler can
cause serious burns.

To st o p t he e n gi n e

STOPorOFF

To s t ar t t he e ng i ne

the ground as illustrated below. Make sure
the chain is free to turn without contacting
any object.

S

Move switch to the

IGNITION

SWITCH

Use only 15”--18” of rope per pull.

Hold saw firmly while pulling starter rope.

The chain must not move

(START)

OFF

CARBURE-

position.

ON

(STOP)

within this manual. Avoid

move the switch to the

position.

hold the saw firmly on

STARTorON

Important points to remember

When pulling the starter rope, do not use
the full extent of the rope as this can
cause the rope to break. Do not let starter
rope snap back. Hold the handle and let
theroperewindslowly.

For cold weather starting, start the unit at
full choke; allow the engine to warm up
before squeezing the throttle trigger.
Do not cut material with the choke lever at
the

FULL

position.

6

Forcold engine or warm engine after run­ning out of fuel.

S

Pull the choke lever out to the full extent.

CHOKE LEVER

(SIDE VIEW)

Choke Lever

S

Press the throttle lockout with your right
hand. Squeeze and hold the throttle trig­ger; Press and hold the fast idle lock with
your forefinger; release the throttle trig­ger.

NOTE

during starting, it will be necessary to re­set the fast idle lock.

S

S

S

S

For a warm engine:

S
S

S
S
S

Difficult starting or flooded engine:

The engine may be flooded with too much
fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ignition
switch is in the

Starting could require pulling the starter
rope handle many times depending on how
badly the unit is flooded. If engine fails to
start refer to the troubleshooting chart or call
your Authorized Service Dealer.

If the throttle trigger is squeezed

:

Pull the starter rope quickly with your right
hand until the engine attempts to start,
then push the choke lever to the half posi­tion.
Pull the starter rope quickly with your right
hand until the engine starts.

Above 40 degrees,

run for approximately five seconds, then
push the choke knob to the off position.
Then, squeeze and release the throttle
trigger to release the fast idle, allowing the
engine to idle.

Below 40 degrees,

warm up 30 seconds to one minute at half
choke. Push choke knob to the off posi­tion; Then, squeeze and release the
throttle trigger to allow engine to idle.

Move on/stop switch to the
Press the throttle lockout with your right
hand. Squeeze and hold the throttle trig­ger; Press and hold the fast idle lock with
your forefinger; release the throttle trig­ger.
Be sure choke is in the
Pull the starter handle until engine starts.
Squeeze and release the throttle trigger to
allow engine to idle.

OFF FULL

allow the engine to

allow the engine to

OFF

ONorSTART

position.

ON

position.

position.

S

Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair parts
as necessary.

S

Keep the chain out of dirt and sand. Even a
small amount of dirt will quickly dull a chain
and increase the possibility of kickback.

S

Practice cutting a few small logs using the
following techniques to get the “feel” of
using your saw before you begin a major
sawing operation.

S

Squeeze the throttle trigger and allow the
engine to reach full speed before cutting.

S

Begin cutting with the saw frame against
the log.

S

Keep the engine at full speed the entire
time you are cutting.

S

Allow the chain to cut for you. Exert only
light downward pressure.

S

Release the throttle trigger as soon as the
cut is completed, allowing the engine to
idle. If you run the saw at full throttle with­out a cutting load, unnecessary wear can
occur.

S

To avoid losing control when cut is com­plete, do not put pressure on saw at end
of cut.

S

Stop the engine before setting the saw
down.

TREE FELLING TECHNIQUES
WARNING:

electrical wires if you do not know the direc­tion of tree fall, at night since you will not be
able to see well, or during bad weather such
as rain, snow, or strong winds. as fall is un­predictable.

Carefully plan your sawing operation in ad­vance. You need a clear area all around the
tree so you can have secure footing. Check
for broken or dead branches which can fall
on you causing serious injury.

Natural conditions that can cause a tree to
fall in a particular direction include:

S

The wind direction and speed.

S

The lean of the tree. The lean of a tree
might not be apparent due to uneven or
sloping terrain. Use a plumb or level to de­termine the direction of tree lean.

S

Weight and branches on one side.

S

Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted,
it can snap and fall toward the operator.

Make sure there is enough room for the tree to
fall. Maintain a distance of
from the nearest person or other objects. En­gine noise can drown out a warning call.

Remove dirt, stones, loose bark, nails, sta­ples, and wire from the tree where cuts are
to be made.

Do not cut near buildings or

2-1/2

tree lengths

Plan a clear retreat path

CUTTING METHODS

IMPORTANT POINTS

S

Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials, etc.

7

45

Direction of Fall

_

FELLING LARGE TREES

(6 inches in diameter or larger)
The notch method is used to fell large trees.

A notch is cut on the side of the tree in the
desired direction of fall. After a felling cut is
made on the opposite side of tree, the tree
will tend to fall into the notch.

NOTCH CUT AND FELLING THE TREE

S

Make notch cut by cutting the top of the
notch first. Cut through
of the tree. Next complete the notch by
cutting the bottom of the notch. See il­lustration. Once the notch is cut remove
the notch of wood from the tree.

S

After removing the cutout of wood, make
the felling cut on the opposite side of the
notch. This is done by making a cut about
two inches higher than the center of the
notch. This will leave enough uncut wood
between the felling cut and the notch to
form a hinge. This hinge will help prevent
the tree from falling in the wrong direction.

First cut

Notch

Second cut

1/3

of the diameter

Final cut here. 2 inches
above center of notch.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fall­en tree to the desired log length.

WARNING:

ing cut. Any portion can roll causing loss of
footing and control. Do not stand downhill
of the log being cut.

mportant points

I

S

Cut only one log at a time.

S

Cut shattered wood very carefully; sharp
pieces of wood could be flung toward op­erator.

S

Use a sawhorse to cut small logs. Never
allow another person to hold the log while
cutting and never hold the log with your
leg or foot.

S

Do not cut in an area where logs, limbs,
and roots are tangled. Drag the logs into a
clear area before cutting by pulling out ex­posed and cleared logs first.

Do not stand on the log be-

TYPES OF CUTTING USED
FOR BUCKING
WARNING:

hung in a log, don’t try to force it out. You
can lose control of the saw resulting in injury
and/or damage to the saw. Stop the saw,
drive a wedge of plastic or wood into the cut
until the saw can be removed easily. Restart
the saw and carefully reenter the cut. Do not
attempt to restart your saw when it is
pinched or hung in a log.

If saw becomes pinched or

Hinge holds tree on stump and helps
control fall

Closing of
notch

NOTE

wedges to open the cut when necessary to
control the direction of f all. Use wood or
plastic wedges, but never steel or iron, to
avoid kickback and chain damage.

S

S

S

Before felling cut is complete, use

:

Be alert to signs that the tree is ready to
fall: cracking sounds, widening of the fell­ing cut, or movement in the upper
branches.
As tree starts to fall, stop saw, put it down,
and get away quickly on your planned re­treat path.
Be extremely cautious with partially fallen
trees that may be poorly supported.
When a tree doesn’t fall completely , set
the saw aside and pull down the tree with
a cable winch, block and tackle, or tractor.
To avoid injury, do not cut down a partially
fallentreewithyoursaw.

Opening
of felling
cut

Overcutting

log with the saw against the log. When over­cutting use light downward pressure.

Undercutting

Undercutting

derside of the log with top of saw against the
log. When undercutting use light upward
pressure. Hold saw firmly and maintain con­trol. The saw will tend to push back toward
you.

WARNING:

down to undercut. The saw cannot be con­trolled in this position.

First cut on pressure side of log

Second cut

8

begins on the top side of the

Overcutting

involves cutting on the un-

Never turn saw upside

Second cut

t

First cut on pressure side of log

BUCKING WITHOUT A
SUPPORT

S

Overcut through

S

Roll log over; finish with a second overcut.

S

Give special attention to logs under strain
to prevent the saw from pinching. Make
the first cut on the pressure side to relieve
the stress on the log.

1/3

of the diameter of log.

BUCKING USING A LOG OR
SUPPORT STAND

S

Remember your first cut is always on the
pressure side of the log.

S

Your first cut should extend
diameter of the log.

S

Finish with your second cut.

Using a support stand

1/3

of the

nd

2

Cut

LIMBING

S

Always limb a tree after it is cut down. Only
then can limbing be done safely and
properly.

S

Leave the larger limbs underneath the
felled tree to support the tree as you work.

S

Start at base of the felled tree and work to­ward the top, cutting branches and limbs.
Remove small limbs with one cut.

S

Keep the tree between you and the chain
as much as possible.

S

Remove larger, supporting branches with

1/3,2/3

the
in the bucking section.

S

Always use an overcut to cut small and
freely hanging limbs. Undercutting could
cause limbs to fall and pinch saw.

cutting techniques described

PRUNING
WARNING:

derheightorbelow.Donotcutifbranches
are higher than your shoulder. Get a profes­sional to do the job.

S

Make your first cut
the bottom of the limb.

S

Next make a 2nd cut

the limb.

a 1 to 2 inch collar from the trunk of the
tree.

Limit pruning to limbs shoul-

1/3

of the way through

Then cut a third overcut leaving

all the way through

1stCut

s

1

Cut

2ndCut

LIMBING AND PRUNING
WARNING:

or prune. Do not stand on ladders, platforms,
a log, or in any position which can cause you
to lose your balance or control of the saw.

MPORTANT POINTS

I

S

Watch out for springpoles. Use extreme
caution when cutting small size limbs. Slen­der material may catch saw chain and be
whipped toward you or pull you off balance.

S

Be alert for springback. Watch out for
branches that are bent or under pressure.
Avoid being struck by the branch or the
saw when the tension in the wood fibers is
released.

S

Frequently clear branches out of the way
to avoid tripping over them.

Never climb into a tree to limb

Second cut

Third cut

Pruning
technique

Collar

First cut

SERVICE

We recommend all service and adjustments
not listed in this manual be performed by an
Authorized Service Dealer.

MAINTENANCE SCHEDULE

Check For:

Fuel Mixture Level Before each use.
Bar Lubrication Before each use...

Chain Tension Before each use....

Chain Sharpness Before each use..
Damaged parts Before each use...

Loose caps Before each use......

Loose fasteners Before each use...

Inspect and Clean:

Bar Before each use.............

Complete saw After each use....

Clean cylinder fins After each use.

Air filter Every 5 hours *..........

Spark arrestor Every 25 hours *....

Replace spark plug
Replace fuel filter

* Hours of Operation

Yearly
Yearly..

9

AIR FILTER
CAUTION:

or other flammable solvent to avoid creating
a fire hazard or producing harmful evapora­tive emissions.

A dirty air filter decreases engine perform­ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.

Do not clean filter in gasoline

Cleaning the air filter:

S

Clean the cover and the area around it to
keep dirt and sawdust from falling into the
carburetor chamber when the cover is re­moved.

S

Remove the parts as illustrated.

S

Wash the filter in soap and water.

S

Replace parts.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced
through the cut, or been run with an improp­er amount of bar lubrication it may be nec­essary to service your bar. A worn bar will
damage your chain and make cutting
difficult.

Replace your bar if bent or the inside rails of
the bar are worn.

S

Clean the oil holes after each 5 hours of
operation

S

Remove sawdust from bar groove period­ically with a wire or putty knife.

Guide Bar
Groove

Oil Holes

CARBURETOR ADJUSTMENTS

Carburetor adjustment is critical and if done
improperly can permanently damage your
unit. We recommend you contact an Autho­rized Service Dealer for adjustments.

IDLE SPEED ADJUSTMENT:

Turn the Idle

Speed Screw clockwise until it stops. Now
turn the screw counterclockwise 4-1/2
turns. This should allow the engine to run
without the chain turning. If the chain moves
at idle speed, do not use your unit. Contact
an Authorized Service Dealer. Idle speed is
correct when engine runs without stalling
and chain does not turn.

MIXTURE ADJUSTMENTS:

retor includes limiter caps (Plastic caps on
the mixture screws) , do not force the screws
beyond the stops of the limiter caps or dam­age will occur. Do not remove these caps.
Small adjustments will affect your unit. Do
not adjust more than 1/16th turn without
checking performance.

If your carbu-

CHAIN SHARPENING

Chain sharpening is a complicated task that
requires special tools. We recommended
you refer chain sharpening to a professional
chain sharpener

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

Replace the spark plug yearly. Gap to .025”.

STORAGE

WARNING:

cool, and secure the unit before storing or
transporting in a vehicle. Store unit and fuel
in an area where fuel vapors cannot reach
sparks or open flames from water heaters,
electric motors or switches, furnaces, etc.
Store unit with all guards in place. Position
so that any sharp object cannot accidentally
cause injury to passersby. Store the unit out
of reach of children.

S

Before storing, drain all fuel from the unit.
Start engine and allow to run until it stops.

S

Clean the unit before storing. Pay particu­lar attention to the air intake area, keeping
it free of debris. Use a mild detergent and
sponge to clean the plastic surfaces.

S

Do not store the unit or fuel in a closed
area where fuel vapors can reach sparks
or an open flame from hot water heaters,
electric motors or switches, furnaces, etc.

S

Store in a dry area out of reach of children.

CAUTION:

deposits from forming in essential fuel sys­tem parts such as the carburetor, fuel filter,
fuel hose, or fuel tank during storage. Alco­hol blended fuels (called gasohol or using
ethanol or methanol) can attract moisture
which leads to fuel mixture separation and
formation of acids during storage. Acidic gas
can damage the engine.

Stop engine and allow t o

It is important to prevent gum

10

TROUBLESHOOTING

Engine will not start.

S

Ignition switch off.

S

Engine flooded.

S

Fuel tank empty.

S

Spark plug not firing.

S

Fuel not reaching carburetor.

Engine will not idle properly.

S

Carburetor requires adjustment.

S

Crankshaft seals worn.

Engine will not accelerate, lacks
power, or dies under a load.

S

Air filter dirty.

S

Spark plug fouled.

S

Carburetor requires adjustment.

Engine smokes excessively.

S

Too much oil mixed with gasoline

LIMITED WARRANTY

FRIGIDAIRE HOME PRODUCTS,

WCI Outdoor Products, Inc., warrants to the
original purchaser that each new Poulanr or
Poulan Pror brand gasoline chain saw is
free from defects in material and workman­ship and agrees to repair or replace under
this warranty any defective gasoline chain
sawasfollowsfromtheoriginaldateofpur­chase.

1 Y E A R ---

Household purposes.

6 0 D A Y S ---

Commercial, Professional, or Income Pro­ducing purposes.

3 0 D A Y S ---

al purposes.
This warranty

not

proper handling, improper maintenance, or
the use of accessories and/or attachments
not specifically recommended by Frigidaire
Home Products for this chain saw. Addition­ally, this warranty
caused by improper handling, improper
maintenance, or if the saw is altered in any
way which in our judgement affects its con­dition or operation. This warranty does not
cover tune--- up, spark plugs, filters, starter
ropes, starter springs, chain sharpening,
bars, chains, and other parts which wear
and require replacement with reasonable
use during the warranty period. This war­ranty
installation of guide bar and chain, and nor­mal adjustments explained in the operator’s
manual such as carburetor adjustments
and chain tension adjustments. This war­ranty
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,

Parts and Labor, when used for

Parts and Labor, when used for

Parts and Labor, if used for rent-

transferable and

cover damage or liability caused by im-

does not

does not

is not

does not

cover predelivery set ---up,

cover transportation costs.

cover damage

Div.

does

AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EXPRES S­LY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA­TIONS ON HOW LONG AN IMPLIED WAR­RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON­SEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
Frigidaire Home Products policy is to con­tinuously improve its products. Therefore,
Frigidaire Home Products reserves the right
to change, modify, or discontinue models,
designs, specifications, and accessories of
all products at any time without notice or ob­ligation to any purchaser.

U.S. EPA/CALIFORNIA

EMISSION CONTROL

WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OB­LIGATIONS:

Protection Agency/California Air Resources
Board and POULAN/WEED EATER, DIVI-

SION OF WCI OUTDOOR PRODUCTS are

pleased to explain the emissions control
system warranty on your lawn and garden
equipment engine. All new utility and lawn
and garden equipment engines must be
designed, built, and equipped to meet the
stringent anti --- smog standards. POULAN/

WEED EATER must warrant the emission

control system on your lawn and garden
equipment engine for the periods of time
listed below provided there has been no
abuse, neglect, or improper maintenance of
your lawn and garden equipment engine.
Your emission control system includes parts
such as the carburetor and the ignition sys­tem. Where a warrantable condition exits,

POULAN/WEED EATER will repair your

lawn and garden equipment engine at no
cost to you. Expenses covered under war­ranty include diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COV­ERAGE:

your engine (as listed under Emissions
Control Warranty Parts List) is defective or a
defect in the materials or workmanship of
the engine causes the failure of such an
emission related part, the part will be re­paired or replaced by POULAN/WEED EAT-

ER.

OWNER’S WARRANTY RESPONSI-

BILITIES:

equipment engine owner,you are responsi­ble for the performance of the required
maintenance listed in your Owner’s Manual.

POULAN/WEED EATER recommends that

you retain all receipts covering mainte­nance on your lawn and garden equipment
engine, but POULAN/WEED EATER cannot
deny warranty solely for the lack of receipts
or for your failure to ensure the performance
of all scheduled maintenance. As the lawn
and garden equipment engine owner, you
should be aware that POULAN/WEED EAT-

ER may deny you warranty coverage if your

The U. S. Environmental

If any emissions related part on

As the lawn and garden

11

lawn and garden equipment engine or a
part of it has failed due to abuse, neglect,
improper maintenance, unapproved modi­fications, or the use of parts not made or ap­proved by the original equipment manufac­turer. You are responsible for presenting
your lawn and garden equipment engine to
a POULAN/WEED EATER authorized repair
center as soon as a problem exists. Warran­ty repairs should be completed in a reason­able amount of time, not to exceed 30 days.
If you have any questions regarding your
warranty rights and responsibilities, you
should contact your nearest authorized ser­vice center or call POULAN/WEED EATER
at 1---800--- 554 ---6723.

MENCEMENT DATE:

begins on the date the lawn and garden
equipment engine is purchased.

OF COVERAGE:

a period of two years from the initial date of
purchase.

OR REPLACEMENT OF PARTS.

replacement of any warranted part will be
performed at no charge to the owner at an
approved POULAN/WEED EATER servic­ing center. If you have any questions re­garding your warranty rights and responsi­bilities, you should contact your nearest
authorized service center or call POULAN/

WEED EATER at 1 ---800--- 554 --- 6723

RANTY PERIOD:

is not scheduled for replacement as re­quired maintenance, or which is scheduled
only for regular inspection to the effect of
“repair or replace as necessary” shall be
warranted for 2 years. Any warranted part
which is scheduled for replacement as re­quired maintenance shall be warranted for
the period of time up to the first scheduled
replacement point for that part.

DIAGNOSIS:

WHAT IS COVERED: REPAIR

WARRANTY COM-

The warranty period

This warranty shall be for

LENGTH

Repair or

WAR-

Any warranted part which

The owner shall not be

charged for diagnostic labor which leads to
the determination that a warranted part is
defective if the diagnostic work is performed
at an approved POULAN/WEED EATER
servicing center.

POULAN/WEED EATER may be li-

AGES:

able for damages to other engine compo­nents caused by the failure of a warranted
part still under warranty.

COVERED

neglect, or improper maintenance are not
covered.

PARTS:

can be grounds for disallowing a warranty
claim. POULAN/WEED EATER is not liable to
cover failures of warranted parts caused by
the use of add--- on or modified parts.

TO FILE A CLAIM:

tions regarding your warranty rights and re­sponsibilities, you should contact your
nearest authorized service center or call

POULAN/WEED EATER at
1--- 800 --- 554 ---6723 .

WARRANTY SERVICE:

or repairs shall be provided at all POULAN/

WEED EATER service centers. call:
1--- 800 ---554--- 6723

PLACEMENT AND REPAIR OF EMISSION
RELATED PARTS

EATER approved replacement part used in

the performance of any warranty mainte­nance or repair on emission related parts
will be provided without charge to the owner
if the part is under warranty.

CONTROL WARRANTY PARTS LIST:

buretor, Ignition System: Spark Plug (cov­ered up to maintenance schedule), Ignition
Module.
The owner is responsible for the perfor­mance of all required maintenance as de-

The use of add--- on or modified parts

CONSEQUENTIAL DAM-

: All failures caused by abuse,

WHAT IS NOT

ADD---ON OR MODIFIED

HOW

If you have any ques-

WHERE TO GET

Warranty services

MAINTENANCE, RE-

:AnyPOULAN/WEED

EMISSION

Car-

MAINTENANCE STATEMENT:

fined in the owner’s manual.

12