Poulan 2001-01, 177110 User Manual
OWNER'S MANUAL
MODEL NO. 271470
13.5 HP 38 INCH
LA WN TRAC T OR
• Assembly
• Operation
• Maintenance
• Service and Adjustments
• Troubleshooting
For Parts and Service, contact our authorized distributor:
call 1-800-849-1297 For Technical Assistance: call 1-800-829-5886
• Repair Parts
177110 Rev. 1 01.30.01 RH
PRINTED IN U.S.A.
TABLE OF CONTENTS
Safety Rules .........................................2
Product Specifications .......................... 5
Assembly ..............................................7
Operation ............................................10
Maintenance Schedule ......................16
Maintenance.......................................16
Service and Adjustments .................... 2 0
Storage ...............................................25
Troubleshooting .................................26
Repair Parts ........................................30
Warranty .............................................46
SAFETY RULES
IMPORTANT: This cutting machine is capable of amputating hands and feet and
throwing objects. Failure to observe the following safety instructions could result in
serious injury or death.
I. GENERAL OPERA TION
• Read, understand, and follow all
instructions in the manual and on the
machine before starting.
• Only allow responsible adults, who are
familiar with the instructions, to operate
the machine.
• Clear the area of objects such as
rocks, toys, wire, etc., which could be
picked up and thrown by the blade.
• Be sure the area is clear of other
people before mowing. Stop machine
if anyone enters the area.
• Never carry passengers.
• Do not mow in reverse unless absolutely necessary. Always look down
and behind before and while backing.
• Be aware of the mower discharge
direction and do not point it at anyone.
Do not operate the mower without
either the entire grass catcher or the
guard in place.
• Slow down before turning.
• Never leave a running machine
unattended. Always turn off blades, set
parking brake, stop engine, and
remove keys before dismounting.
• Turn off blades when not mowing.
• Stop engine before removing grass
catcher or unclogging chute.
• Mow only in daylight or good artificial
light.
• Do not operate the machine while
under the influence of alcohol or drugs.
• Watch for traffic when operating near or
crossing roadways.
• Use extra care when loading or
unloading the machine into a trailer or
truck.
• Data indicates that operators, age 60
years and above, are involved in a
large percentage of riding mowerrelated injuries. These operators
should evaluate their ability to operate
the riding mower safely enough to
protect themselves and others from
serious injury.
II. SLOPE OPERA TION
Slopes are a major factor related to loss-ofcontrol and tipover accidents, which can
result in severe injury or death. All slopes
require extra caution. If you cannot back up
the slope or if you feel uneasy on it, do not
mow it.
DO:
• Mow up and down slopes, not across.
• Remove obstacles such as rocks, tree
limbs, etc.
• Watch for holes, ruts, or bumps.
Uneven terrain could overturn the
machine.
• Use slow speed. Choose a low gear
so that you will not have to stop or shift
while on the slope.
• Follow the manufacturer’s recommendations for wheel weights or counterweights to improve stability.
• Use extra care with grass catchers or
other attachments. These can change
the stability of the machine.
• Keep all movement on the slopes
and
changes in speed or direction.
• Avoid starting or stopping on a slope. If
tires lose traction, disengage the
blades and proceed slowly
down the slope.
DO NOT:
•
Do not
sary, and then, turn slowly and gradually downhill, if possible.
•
Do not
embankments. The mower could
suddenly turn over if a wheel is over
the edge of a cliff or ditch, or if an edge
caves in.
•
Do not
traction could cause sliding.
•
Do not
putting your foot on the ground.
2
Tall grass can hide obstacles.
gradual
. Do not make sudden
straight
turn on slopes unless neces-
mow near drop-offs, ditches, or
mow on wet grass. Reduced
try to stabilize the machine by
slow
ONLY RIDE UP AND DOWN HILL,
NOT ACROSS HILL
15° MAX.
SIGHT AND HOLD THIS LEVEL WITH
SKY LINE OR TREE.
CUT OUT ON DOTTED LINES
THIS IS A 15° SLOPE
Operate your Tractor up and down the face of slopes (not
greater than 15°), never across the face. Make turns gradu-
ally to prevent tipping or loss of control. Exercise extreme
caution when changing direction on slopes.
SIGHTING
GUIDE
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION
47
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product
as manufactured is free from defects in materials and workmanship. For a period
of one (1) year from date of purchase by the original consumer purchaser, we will
repair or replace, at our option, without charge for parts or labor incurred in
replacing parts, any part which we find to be defective due to materials or
workmanship. This Warranty is subject to the following limitations and exclusions.
1.This warranty does not apply to the engine, other than EHP manufactured
transaxle/transmission components, battery (except as noted below) or
components parts thereof. Please refer to the applicable manufacturer's
warranty on these items.
2.Transportation charges for the movement of any power equipment unit or
attachment are the responsibility of the purchaser. Transportation charges for
any parts submitted for replacement under this warranty must be paid by the
purchaser unless such return is requested by Electrolux Home Products.
3.Battery Warranty: On products equipped with a Battery, we will replace,
without charge to you, any battery which we find to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we
will exchange the Battery, charging you 1/12 of the price of a new Battery for
each full month from the date of the original sale. Battery must be maintained
in accordance with the instructions furnished.
4.The Warranty period for any products used for rental or commercial purposes
is limited to 90 days from the date of original purchase.
5.This Warranty applies only to products which have been properly assembled,
adjusted, operated, and maintained in accordance with the instructions
furnished. This Warranty does not apply to any product which has been
subjected to alteration, misuse, abuse, improper assembly or installation,
delivery damage, or to normal wear of the product.
6.Exclusions: Excluded from this Warranty are belts, blades, blade adapters,
normal wear, normal adjustments, standard hardware and normal maintenance.
7.In the event you have a claim under this Warranty, you must return the product
to an authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please
contact:
Electrolux Home Products
a division of WCI Outdoor Products, Inc.
Outdoor Products Customer Service Dept.
250 Bobby Jones Expressway
Augusta, GA 30909 USA
In Canada contact:
Electrolux Home Products
a division of WCI Outdoor Products, Inc
7075 Ordan Drive
Mississauga, Ontario
L5T 1K6
SAFETY RULES
III. CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the
machine and the mowing activity.
assume that children will remain where
you last saw them.
• Keep children out of the mowing area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
• Before and when backing, look behind
and
down
• Never carry children. They may fall off
and be seriously injured or interfere
with safe machine operation.
• Never allow children to operate the
machine.
• Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.
for small children.
IV . SER VICE
• Use extra care in handling gasoline
and other fuels. They are flammable
and vapors are explosive.
- Use only an approved container.
-Never remove gas cap or add fuel
with the engine running. Allow
engine to cool before refueling. Do
not smoke.
-Never refuel the machine indoors.
-Never store the machine or fuel
container inside where there is an
open flame, such as a water heater.
Never
• Never run a machine inside a closed
area.
• Keep nuts and bolts, especially blade
attachment bolts, tight and keep
equipment in good condition.
• Never tamper with safety devices.
Check their proper operation regularly.
• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel
spillage. Allow machine to cool before
storing.
• Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
• Never make adjustments or repairs
with the engine running.
• Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown. Frequently
check components and replace with
manufacturer's recommended parts,
when necessary.
• Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when servicing them.
• Check brake operation frequently.
Adjust and service as required.
giving the model number, serial number and date of purchase of your product
and the name and address of the authorized dealer from whom it was purchased.
THIS W ARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME
TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES.
Some areas do not allow the limitation of consequential damages or limitations
of how long an implied Warranty may last, so the above limitations or exclusions
may not apply to you. This Warranty gives you specific legal rights, and you may
have other rights which vary from locale to locale.
This is a limited Warranty within the meaning of that term as defined in the
Magnuson-Moss Act of 1975.
46
• Be sure the area is clear of other
people before mowing. Stop machine if
anyone enters the area.
• Never carry passengers or children
even with the blades off.
• Do not mow in reverse unless absolutely necessary. Always look down
and behind before and while backing.
• Never carry children. They may fall off
and be seriously injured or interfere
with safe machine operation.
• Keep children out of the mowing area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
• Before and when backing, look behind
and down for small children.
• Mow up and down slopes (15° Max),
not across.
• Remove obstacles such as rocks, tree
limbs, etc.
• Watch for holes, ruts, or bumps.
Uneven terrain could overturn the
machine. Tall grass can hide obstacles.
3
SAFETY RULES
• Use slow speed. Choose a low gear so
that you will not have to stop or shift
while on the slope.
• Avoid starting or stopping on a slope. If
tires lose traction, disengage the
blades and proceed slowly straight
down the slope.
• If machine stops while going uphill,
disengage blades, shift into reverse
and back down slowly.
• Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.
Look for this symbol to point out
important safety precautions. It means
CAUTION!!! BECOME ALERT!!! YOUR
SAFETY IS INVOLVED.
CAUTION: In order to prevent
accidental starting when setting up,
transporting, adjusting or making repairs,
always disconnect spark plug wire and
place wire where it cannot contact spark
plug.
CAUTION: Do not coast down a hill
in neutral, you may lose control of the
tractor.
CAUTION: Tow only the attachments
that are recommended by and comply
with specifications of the manufacturer of
your tractor. Use common sense when
towing. Operate only at the lowest
possible speed when on a slope. Too
heavy of a load, while on a slope, is
dangerous. Tires can lose traction with
the ground and cause you to lose control
of your tractor.
WARNING: Engine exhaust, some of
its constituents, and certain vehicle
components contain or emit chemicals
known to the State of California to cause
cancer and birth defects or other reproductive harm.
WARNING: Battery posts, terminals
and related accessories contain lead and
lead compounds, chemicals known to the
State of California to cause cancer and
birth defects or other reproductive harm.
Wash hands after handling.
TRACTOR -- MODEL NUMBER 271470
MOWER DECK
KEY PART
NO. NO. DESCRIPTION
1 170280 Mower Housing Assembly
2 72140506 Bolt, Carriage 5/16-18 x 3/4
3 138017 Bracket Asm. Fram Sway Bar
4 169970 Bracket, Asm. Deck Sway
5 4939M Retainer, Spring
6 130832 Asm. Suspension Rear
8 850857 Bolt, Hex 3/8-24 x 1-1/4 Gr 8
9 10030600 Washer, Lock, Hlcl Sprg 3/8
10 140296 Washer, Hard Blade Mower
11 134148 Blade, Mower, Mulching 38"
13 137645 Shaft and Bearing Assembly
14 128774 Mandrel Housing, Vented
15 110485X Ball Bearing, Mandrel
16 140329 Stripper, Mower, Vented
19 132827 Bolt, Shoulder
21 73680500 Nut, Crownlock 5/16-18
23 137607 Bracket, Mower Deflector
24 105304X Cap, Sleeve
25 123713X Spring, Deflector
26 110452X Nut, Push
27 106736X428 Shield, Deflector
28 19111016 Washer 11/32 x 3/4 x 16 Ga
29 106735X Rod, Hinge
30 157722 Screw, Thdro Washer Hd
31 129963 Washer, Spacer
32 153532 Pulley, Mandrel
33 137266 Nut, Flangelock 9/16
36 131494 Pulley, Idler, Flat
40 73680600 Nut Crownlock 3/8-16
45 4497H Retainer, Spring
53 130840 Brake Assembly
54 133943 Washer Hardened
55 133840 Idler Arm Assembly
Bar
Vented
(Includes Key Number 15)
KEY PART
NO. NO. DESCRIPTION
56 165723 Spacer, Retainer
67 149846 Knob
68 144200 Belt
69 76020312 Pin, Cotter 3/32 x 3/4
86 7631J Runner, LH
87 128772 Runner, RH
88 19111216 Washer 11/32 x 3/4 x 16 Ga
89 19131612 Washer 13/32 x 1 x 12 Ga
107 133502 Spacer, Retainer
108 133503 Stiffener, Idler Arm
109 74760640 Bolt, Hex Head 3/8-16 x2-1/2
110 142587 Upstop Deck Front 38"
113 17060512 Screw 5/16-18 x 3/4
122 131289 Rod, Brake, LH
123 169971 Rod, Brake, RH
146 165891 Bolt Carriage Idler
148 169022 Spring Return Idler
149 165898 Retainer Spring Yellow Zinc
150 19091216 Washer 9/32 x 3/4 x 16 Ga.
151 169670 Bracket Clutch
152 172758 Cable Clutch 38 In
153 169674 Washer Flat 3/8” Type B
154 169675 Spring Retainer
155 169671 Spring Retention Lever
156 169672 Spacer
157 169669 Rod Clutch
158 17720410 Screw Hex Thd Cut
- - 130794 Mandrel Assembly (Includes
- - 171665 Mower Deck, Complete
NOTE: All component dimensions given in U. S.
inches 1 inch = 25.4 mm
1/4-20x5/8
Key Numbers 12-15, 17-19,
31 and 33)
4
45
MOWER DECK
158
151
152
5
157
153
21
1
2
3
6
TRACTOR -- MODEL NUMBER 271470
40
146
4
2
3
8
56
113
148
108
36
89
36
33
32
31
40
150
45
53
30
13
154
89
107
67
156
153
155
69
55
54
123
122
109
89
2
86
16
4
2
110
PRODUCT SPECIFICA TIONS
GASOLINE 1.25 GALLONS
CAPACITY UNLEADED
AND TYPE: REGULAR
OIL TYPE SAE 30(ABOVE 32°F)
(API-SF/SJ): SAE 5W-30
68
OIL CAPACITY: 3 PTS
SPARK PLUG: CHAMPION
(GAP: .030”) RJ19LM
VALVE INTAKE: .005”-.007”
CLEARANCE: EXHAUST:.009”-.011”
GROUND SPEED FORWARD:
(MPH): 1ST 1.1
TIRE FRONT: 14 PSI
PRESSURE: REAR: 12 PSI
CHARGING 3 AMPS BATTERY
(Below 32°F)
2ND 2.2
3RD 3.4
4TH 4.3
5TH 5.5
REVERSE: 1.7
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintain-
ing, caring for and using your tractor.
• Follow the instructions under “Maintenance” and “Storage” sections of this
owner’s manual.
WARNING: This tractor is equipped
with an internal combustion engine and
should not be used on or near any
unimproved forest-covered, brushcovered or grass-covered land unless
the engine’s exhaust system is equipped
with a spark arrester meeting applicable
local or state laws (if any). If a spark
arrester is used, it should be maintained
in effective working order by the operator.
In the state of California the above is
required by law (Section 4442 of the
California Public Resources Code).
Other states may have similar laws.
Federal laws apply on federal lands. A
spark arrester for the muffler is available
through your nearest authorized service
center/Department (See REPAIR PARTS
section of this manual).
SYSTEM: 5 AMPS HEADLIGHTS
BATTERY: AMP/HR: 25
21
88
87
BLADE BOLT 27-35 FT. LBS
MIN. CCA: 190
CASE SIZE:U1R
TORQUE:
26
28
25
24
CONGRATULATIONS on your purchase
of a new tractor. It has been designed,
engineered and manufactured to give
you the best possible dependability and
21
2
15
29
21
23
performance.
Should you experience any problem you
cannot easily remedy, please contact
your nearest authorized service center.
We have competent, well-trained
14
technicians and the proper tools to
service or repair this tractor.
Please read and retain this manual. The
27
instructions will enable you to assemble
and maintain your tractor properly.
Always observe the “SAFETY RULES”.
19
21
149
44
11
10
9
8
5
UNASSEMBLED PARTS
Steering
Wheel Insert
(1) Hex Bolt 5/16-18 x 1-1/4
Steering Wheel
Adapter
Steering Wheel
(1) Locknut 5/16-18
(1) Hex Bolt
3/8-16 x 1
(1) Large Flat Washer
(1) Lockwasher 3/8
Steering
Extension
Steering
Boot
Shaft
LIFT ASSEMBLY
TRACTOR -- MODEL NUMBER 271470
KEY PART
NO. NO. DESCRIPTION
1 159460 Wire Asm Inner W/plunger
2 159471 Shaft Asm Lift
3 105767X Pin Groove 1 500 Zinc
4 12000002 E Ring #5133-62
5 19211621 Washer Pltd 21/32 X 1 X 21ga
6 120183X Bearing Nylon Blk 629 Id
7 125631X Grip Handle Fluted Blk
8 122365X Button Plunger Red
11 139865 Link Lift LH
12 139866 Link Lift RH
13 4939M Retainer Spring
15 173288 Link Front
16 73350800 Nut Jam Hex 1/2-13 Unc
17 130171 Trunnion Blk Zinc
18 73800800 Nut Lock w/Wsh 1/2-13 UNC
19 139868 Arm Suspension Rear
20 163552 Retainer Spring Zinc
31 169865 Bearing Pvt Lift
32 73540600 Nut Crownlock 3/8-24
Keys
(2) Keys
Seat
(1) Washer
17/32 x 1-3/16 x 12 Gauge
(1)Knob
6
Slope Sheet
NOTE: All component dimensions given in U. S.
inches 1 inch = 25.4 mm
43
LIFT ASSEMBLY
11
19
13
31
32
13
TRACTOR -- MODEL NUMBER 271470
5
3
2
20
31
32
13
12
4
6
13
19
15
ASSEMBLY
Your new tractor has been assembled at the factory with exception of those parts left
unassembled for shipping purposes. To ensure safe and proper operation of your
tractor all parts and hardware you assemble must be tightened securely. Use the
7
8
1
6
20
20
5
4
20
18
17
16
15
correct tools as necessary to insure proper tightness. Review the video cassette before
you begin.
TOOLS REQUIRED FOR
ASSEMBLY
A socket wrench set will make assembly
easier. Standard wrench sizes you need
are listed below.
(1) 9/16" wrench (1) Pliers
(2) 1/2" wrench (1) Utility knife
(1) Tire pressure gauge
When right or left hand is mentioned in
this manual, it means, from your point of
view, when you are in the operating
position (seated behind the steering
wheel).
TO REMO VETRACT OR FROM
CARTON
• Assemble large flat washer, 3/8 lock
washer, 3/8 hex bolt and tighten
securely.
• Snap steering wheel insert into center
of steering wheel.
• Remove protective materials from
tractor hood and grill.
IMPORTANT: Check for and remove any
staples in skid that may puncture tires
where tractor is to roll off skid.
Steering Wheel Insert
Bolt
3/8 Lock Washer
Large Flat Washer
• Remove all accessible loose parts
and parts cartons from carton.
• Cut, from top to bottom, along lines on
all four corners of carton, and lay
panels flat.
Steering Wheel
Tabs
• Check for any additional loose parts
or cartons and remove.
BEFORE REMOVING TRA CTOR
FROM SKID
ATTACH STEERING WHEEL
ASSEMBLE EXTENSION SHAFT AND
BOOT
• Slide extension shaft onto lower
steering shaft. Align mounting holes in
extension and lower shafts and install
5/16 hex bolt and locknut. Tighten
Steering Boot
Adapter
5/16 Locknut
Lower Steering
Shaft
Extension Shaft
5/16 Hex Bolt
Tab
Slots
securely.
• Place tabs of steering boot over tab
slots in dash and push down to secure.
INSTALL STEERING WHEEL
• Position front wheels of the tractor so
they are pointing straight forward.
• Remove steering wheel adapter from
steering wheel and slide adapter onto
steering shaft extension.
• Position steering wheel so cross bars
are horizontal (left to right) and slide
inside boot and onto adapter.
HOW T O SET UP YOUR TRACT OR
CHECK BATTERY
• Lift seat pan to raised position and
open battery box door.
• If this battery is put into service after
month and year indicated on label
(label located between terminals)
charge battery for minimum of one hour
at 6-10 amps. (See "BATTERY" in
Maintenance section of this manual for
charging instructions).
42
7
Seat Pan
Battery Box
Door
Terminal
Label
Terminal
INSTALL SEAT
Adjust seat before tightening adjustment
knob.
• Remove adjustment knob and flat
washer securing seat to cardboard
packing and set aside for assembly of
seat to tractor.
• Pivot seat upward and remove from
the cardboard packing. Remove the
cardboard packing and discard.
• Place seat on seat pan so head of
shoulder bolt is positioned over large
slotted hole in pan.
• Push down on seat to engage
shoulder bolt in slot and pull seat
towards rear of tractor.
• Pivot seat and pan forward and
assemble adjustment knob and flat
washer loosely. Do not tighten.
• Lower seat into operating position
and sit in seat.
• Slide seat until a comfortable position
is reached which allows you to press
clutch/brake pedal all the way down.
• Get off seat without moving its
adjusted position.
• Raise seat and tighten adjustment
knob securely.
Seat
Seat Pan
Flat Washer
Adjustment
Knob
Shoulder
Bolt
NOTE: You may now roll or drive your
tractor off the skid. Follow the appropriate
instruction below to remove the tractor
from the skid.
TO R OLL TRA CTOR OFF SKID (S ee
Operation section for location and
function of controls)
• Press lift lever plunger and raise
attachment lift lever to its highest
position.
• Release parking brake by depressing
clutch/brake pedal.
• Place gearshift lever in neutral (N)
position.
• Roll tractor forward off skid.
• Remove banding holding deflector
shield up against tractor.
TO DRIVE TRACT OR OFF SKID (See
Operation section for location and
function of controls)
WARNING: Before starting, read,
understand and follow all instructions in
the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be
sure the area in front of tractor is clear of
other people and objects.
• Be sure all the above assembly steps
have been completed.
• Check engine oil level and fill fuel tank
with gasoline.
• Sit on seat in operating position,
depress clutch/brake pedal and set the
parking brake.
• Place gear shift lever in neutral (N)
position.
• Press lift lever plunger and raise
attachment lift lever to its highest
position.
• Start the engine. After engine has
started, move throttle control to idle
position.
• Depress clutch/brake pedal into full
“BRAKE” position and hold. Move
gearshift lever to 1st gear.
• Slowly release clutch/brake pedal and
slowly drive tractor off skid.
• Apply brake to stop tractor, set parking
brake and place gearshift lever in
neutral position.
• Turn ignition key to “OFF” position.
Continue with the instructions that follow.
8
TRACTOR -- MODEL NUMBER 271470
DECALS
4
KEY PART
1 177109 Decal Lower Dash
2 176394 Decal Engine
3 171828 Decal Hood
4 171829 Decal Fender
5 145005 Decal Battery Danger
7 171830 Decal Steering
8 156867 Decal, Oper sdl P/L Gear
11 156439 Decal Fender Dnger
1
2
15
12
WHEELS AND TIRES
1
2
6
5,8
4,10
7
3,9
3
11
3
KEY PART
12 4900J Decal, Clutch/Brake Eng
13 146046 Decal V-Belt Dr Sch tractor
15 136832 Decal V-Belt sch
- - 138311 Decal Handle Lft Height
- - 177110 Owner’s Manual, English
- - 177111 Owne r’s Manual, Spanish
KEY PART
NO. NO. DESCRIPTION
1 59192 Cap Valve Tire
2 65139 Stem Valve
3 106222X Tire F Ts 15 X 6 0 - 6 Service
4 59904 Tube Front (Service Item Only)
5 106732X427 Rim Asm 6"front White Service
6 278H Fitting Grease (Front Wheel Only)
7 9040H Bearing Flange (front Wheel
8 106108X427 Rim Asm 8"rear White Service
9 124635X Tire Rear
10 7152J Tube Rear (Service Item Only)
11 104757X428 Cap Axle Blk 1 50 X 1 00
- - 144334 Sealant, Tire ( 10 oz. Tube)
NOTE: All component dimensions given in U. S.
inches 1 inch = 25.4 mm
Adjust (Lift Handle)
Only)
7
11
8
13
5
41
Loading...