Poulan 115351127, 952711923 User Manual

Please do not return product to retailer. Por favor, no devuelva el producto al lugar de compra. Veuillez ne pas retourner le produit au détaillant.

1--800--554--6723

www.poulanpro.com

Instruction Manual

Manual de Instrucciones

ENGLISH

Manuel d’Instructions

BVM200VS

IMPORTANT MANUAL -- Do not throw away MANUAL IMPORTANTE -- No lo descarte MANUEL IMPORTANT -- À Conserver

WARNING:

Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves.

AVERTISSEMENT:

Veuillez lire le manuel d’instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. Tout défaut de le faire pourrait entraîner des blessures graves.

Poulan PRO 7349 Statesville Road Charlotte, NC 28269

850 Matheson Blvd. West

Mississauga, Ontario L5V 0B4

115351127 Rev. 2 3/1/10 BRW

Poulan PRO

ESPAÑOL

FRANÇAIS

IDENTIFICATION OF SAFETY SYMBOLS

WARNING: This unit can be dangerous! Careless or improper

use can cause serious injury.

WARNING: Read the operator’s manual before use. Failure to

follow instructions could result in serious injury to the operator and/or bystanders. Save operator’s manual.

The blower can throw objects violently. You can be blinded or injured. Always wear hearing protection and safety glasses marked Z87. Always wear heavy, long pants, long sleeves, boots and gloves.

Hazard zone for thrown objects. Keep children, bystanders, and animals away from work area a minimum of 30 feet (10 meters) when starting or operating unit. Do not point blower nozzle in the direction of people or pets.

Secure hair above shoulder length. Do not wear jewelry, loose clothing, or clothing with loosing hanging straps, ties, tassels, etc. They can be caught in moving parts.

Always stop unit and disconnect spark plug before cleaning or servicing.

WARNING: Stop the engine before opening the vacuum inlet door. The engine must

be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades. Gently tilt the handle of the screwdriver toward the front of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand.

-- 2 --

IDENTIFICATION OF SAFETY SYMBOLS

When using the vacuum attachment, the unit is designed to pick up dry material such as leaves, grass, small twigs, and bits of paper. Do not vacuum stones, gravel, metal, broken glass, etc., to avoid severe damage to the impeller.

WARNING: Fire hazard. Never mix, pour, or store gasoline or

use the unit near a flame or sparks (including smoking, open flames, or work that can cause sparks).

WARNING: The muffler is very hot during and after use. Do

not touch the muffler, muffler guard, or surrounding surfaces, or allow combustible material such as dry grass or fuel to do so.

SAFETY RULES

WARNING: Failure to follow all

Safety Rules and Precautions can result in serious injury.

KNOW YOUR UNIT

S Read your instruction manualcarefully until

you completely understand and can follow all warnings and safety rules before operating the unit.

D Restrict unit to users who understand and

will follow all warnings and safety rules in this manual.

WARNING: Inspect area before start-

ing unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation.

Use your unit as a blower for:

D Sweeping debris or grass clippings from

driveways, sidewalks, patios, etc.

D Blowing grass clippings, straw, or leaves into

piles, around joints, or between bricks.

Use your unit as a vacuum for:

D Picking up dry materia l such as leaves,

grass, small twigs, and bits of paper.

D For best results during vacuum use, operate

your unit at high speed.

D Move slowly back and forth over the mate-

rial as you vacuum. Avoid forcing the unit into a pileof debris as this can clog the unit.

D Keep the vacuum tube about an inch above

the ground for best results.

PLAN AHEAD

D Always wear eye protection when operat-

ing, servicing, or performing maintenance on unit. Wearing eye protection will help to prevent rocks or debris from being blown or ricocheting into eyes and face which can

result in blindness and/or serious injury. Eye protection should be marked Z87.

D Always wear foot protection. Do not go

barefoot or wear sandals.

D Always wear respirator or face mask when

working with unit in dusty environments.

D Secure hair so it is above shoulder length.

Keep loose hair, loose clothing, fingers, and all other parts of the body away from openings and moving parts. Hair, jewelry, loose clothing, or clothing with loosely hanging straps, ties, tassels, etc., can be caught in moving parts.

D Do not operate unit when you are tired, ill, up-

set, or if you are under the influence of alcohol, drugs, or medication.

D Keep children, bystanders, and animals

away from work area a minimum of 30 feet (10 meters) when starting or operating unit. Do not point the blower nozzle in the direction of people or pets.

HANDLE FUEL WITH CAUTION, IT IS HIGHLY FLAMMABLE

D Eliminate all sources of sparks or flame (in-

cluding smoking, open flames, or work that can cause sparks) in the areas where fuel is mixed, poured, or stored.

D Mix and pour fuel in an outdoor area; store

fuel in a cool, dry, well ventilated place; use an approved, marked container for all fuel purposes.

D Do not smoke while handling fuel or while

operating the unit.

D Make sure the unit is properly assembled

and in good operating condition.

D Do not fill fuel tank while engine is hot or

running.

D Avoid spilling fuel or oil. Wipe up fuel spills

before starting engine.

-- 3 --

D Move at least 10 feet (3 meters) away from

fuel and fueling site before starting engine.

D Always store gasoline in a container ap-

proved for flammable liquids.

OPERATE YOUR UNIT SAFELY

WARNING: Stop the engine before

opening the vacuum inlet door. The engine must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades.

D Inspect unit before each use for worn,

loose, missing, or damaged parts. Do not use until unit is in proper working order.

D Keep outside surfaces free of oil and fuel. D Never start or run engine inside a closed

room, building or other unventilated area. Breathing exhaust fumes can kill.

D To avoid static electricity discharge, do not

wear rubber gloves or any other insulated gloves while operating unit.

D Do not set unit on any surface except a

clean, hard area while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through discharge opening, damaging unit, property, or causing serious injury to bystanders or operator.

D Avoid dangerous environments. Do not use

in unventilated areas or where explosive vapors or carbon monoxide build up could be present.

D Do not overreach or use from unstable sur-

faces such as ladders, trees, steep slopes, rooftops, etc. Keep firm footing and balance at all times.

D Never place objects inside the blower

tubes; always direct the blowing debris away frompeople, animals,glass, and solid objects such as trees, automobiles, walls, etc.The forceof air can cause rocks, dirt, or sticks to be thrown or to ricochet which can hurt people or animals, break glass, or cause other damage.

D Never run unit without the proper equip-

ment attached. When using your unit as a blower, always install blower tubes. When using your unit as a vacuum, always install vacuum tubes and vacuum bag assembly. Make sure vacuum bag assembly is completely zipped.

D Check air intake opening, blower tubes,

vacuum tubes, and elbow tube frequently, always with engine stopped and spark plug disconnected. Keep vents and discharge tubes free of debris which can accumulate and restrict proper air flow.

D Never place any object in the air intake open-

ing as this could restrict proper air flow and cause damage to the unit.

D Never use for spreading chemicals, fertiliz-

ers, orother substances which may contain toxic materials.

D To avoid spreading fire, do not use near leaf

or brush fires, fireplaces, barbecue pits, ashtrays, etc.

D Use only for jobs explained in this manual.

MAINTAIN YOUR UNIT PROPERLY

WARNING: Disconnect spark plug be-

fore performing maintenance except for carburetor adjustments.

D Have all maintenance other than the rec-

ommended procedures described in the instruction manual performed by an authorized service dealer.

D Use only recommended Poul an PRO re-

placement parts; use of any other parts may void your warranty and cause damage to your unit.

D Empty fuel tank before storing the unit. Use

up fuel left in carburetor by starting engine and letting it run until it stops.

D Do not use any accessory or attachment

other than those recommended by manufacturer for use with your unit.

D Do not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an open flame from hot water heaters, electric motors or switches, furnaces, etc.

D Store in a dry area out of reach of children.

WARNING: The engine exhaust from

this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

SPECIAL NOTICE: Exposure to vibra-

tions through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swelling. Prolonged use in cold weather has been linked toblood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An antivibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.

SPECIAL NOTICE: This unit is equipped

with a temperature limiting muffler and spark arresting screen which meets the requirements of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion engines be equipped with a spark arresting screen. If you operate in alocale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. Refer to the MAINTENANCE section for information on maintenance of the muffler and spark arresting screen.

-- 4 --

ASSEMBLY

WARNING: Stop engine and be sure

the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or accessing movable parts.

WARNING: If you receive your unit

assembled, check each step to insure your unit is properly assembled and all fasteners are secure. Follow all safety information in the manual and on the unit.

D A standard screwdriver is required for as-

sembly.

BLOWER TUBE ASSEMBLY

1. Align the rib on the upper blower tube with the groove in the blower outlet; slide the tube into place.

NOTE: Knob must be loose enough to allow

blower tube to be inserted in blower outlet. Loos en knob by turning counterclockwise.

Blower Outlet

Rib

Groove

2. Secure thetube by turning the knob clockwise.

3. Align the slots on the lower blower tube with the tabs on the upper blower tube.

Upper Blower Tube

Lower Blower Tube

6. To remove the tubes, turn the knob counterclockwise to loosen the tubes; remove the tubes.

HIGH--SPEED NOZZLE ASSEMBLY

When greater air speed is desired, use the high--speed nozzle.

1. Align the slots on the nozzle with the tabs on the lower blower tube.

High--Speed Nozzle

Lower Blower Tube

2. Slide the nozzle onto the lower blower tube.

3. Turn the nozzle clockwise until a click is felt to secure the nozzle to the lower blower tube.

VACUUM BAG ASSEMBLY

1. Open the zipper on the vacuum bag and insert the elbow tube.

2. Push the small end of the elbow tube through the small opening in the bag.

Zipper Opening

NOTE: Make sure edge of the small opening

is flush against the flared area of the elbow tube, and the rib on the elbow tube is on the bottom.

3. Close the zipper on the bag. Make sure the zipper is closed completely.

4. Remove blower tubes from engine.

Elbow Tube

Tab

Small Opening

Slot

Rib

Tab

Slot

4. Slide the lower blower tube onto the upper blower tube.

5. Turn the lower blower tube clockwise until a click is felt to secure the lower blower tube to the upper blower tube.

NOTE: When the upper and lower blower

tubes are assembled together properly, the arrows on both tubes will be aligned.

Rib

Groove

5. Insert the elbow tube into the blower outlet. Make sure elbow tube rib is aligned with the blower outlet groove.

6. Turnknob clockwise tosecure elbow tube.

VACUUM TUBE ASSEMBLY

WARNING: Stop engine and be sure

the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or

-- 5 --

+ 9 hidden pages