Poulan 952711880, 115274026 User Manual

Page 1

Please do not return product to retailer. Por favor, no devuelva el producto al lugar de compra. Veuillez ne pas retourner le produit au détaillant.

1--800--554--6723

www.poulanpro.com

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

PP325

ENGLISH ESPAÑOL

For Occasional Use Only

DANGER:

Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury.

PELIGRO:

Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves.

DANGER:

Lire le manuel d’instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. Tout défaut de le faire pourrait entraîner des blessures graves.

Poulan PRO 7349 Statesville Road Charlotte, NC 28269

115274026 Rev. 2 3/1/10 BRW

FRANÇAIS

Page 2

IDENTIFICATION OF SAFETY SYMBOLS

DANGER: Blade can thrust violently

away from material it does not cut. Blade thrust can cause amputation of arms or legs. Keep people and animals 50 feet (15 meters) away.

WARNING: The blade continues to spin after

the trigger is released or engine is turned off. The coasting blade can throw objects or seriously cut if accidentally touched. Stop the blade by contacting the right hand side of the coasting blade with material already cut.

WARNING: This unit can be dangerous! Careless or improper

use can cause serious injury.

WARNING: Always use a metal shield and dust cup in the order

shown when using blades. Always use a handlebar and shoulder strap. Ensure handlebar remains installed at all times.

WARNING: Read the operator’s manual before use. Failure to

follow instructions could result in serious injury to the operator and/or bystanders. Save operator’s manual.

Blade/trimmer line can throw objects violently. You can be blinded or injured. Always wear hearing protection and safety glasses marked Z87. Always wear head protection, heavy, long pants, long sleeves, boots and gloves.

Secure hair above shoulder length. Do not wear jewelry, loose clothing, or clothing with loosely hanging straps, ties, tassels, etc. They can be caught in moving parts.

Hazard zone for thrown objects.

S Blade/trimmer line throws objects violently. S You and others can be blinded/injured. S Keep children, bystanders, and animals 50 feet

(15 meters) away.

Page 3

IDENTIFICATION OF SAFETY SYMBOLS

Assist handle to be positioned only below the arrow.

Never allow children to operate this unit.

Store unit indoors in a high, dry place out of the reach of children. Store unit and fuel in ar ea wher e fuel vapors cannot reach sparks or open flames from water heaters, electric motor s or switch e s, fu r naces, etc.

When servicing unit, use only identical replacement parts.

Always stop unit and disconnect spark plug before cleaning or servicing.

WARNING: Fire hazard. Never mix, pour, or store gasoline or

use the unit near a flame or sparks (including smoking, open flames, or work that can cause sparks).

Use unleaded gasoline and two--stroke oil mixed at a ratio of 40:1 (2.5%).

SAFETY RULES

WARNING: When using gardening

appliances, basic safety precautions must always be followed to reduce the risk of fire and serious injury.

DANGER: This power tool can be dan-

gerous! This unit can cause serious injury including amputation or blindness to the operator and others. The warnings and safety instruc tions in this manual must be followed to provide reasonable safety and efficiency in using the unit. The operator is responsible for following the warnings and instructions in this manual and on

Page 4

the unit. Read the entire instruction manual before assembling and using the unit! Restrict the use of this unit to persons who read, understand, and follow the warnings and instructions in this manual and on the unit. Never allow children to operate this unit.

INSTRUCTION MANUAL

WARNING: Do not use trimmerhead

as a fastening device for the blade.

If situations occur which are not covered in this manual, use care and good judgment. If you need assistance, contact contact an authorized service dealer or call 1- -800- -554--6723.

OPERATOR SAFETY

S Dress properly. Always wear safety

glasses or similar eye protection when operating, or performing maintenance on your unit (safety glasses are available). Eye protection should be marked Z87.

S Always wear face or dust mask if operation

is dusty.

S Always wear heavy, long pants, long sleeves,

boots, and gloves. Wearing safety leg guards is recommended.

S Always wear foot protection. Do not go

barefoot or wear sandals.

S Secure hair above shoulder length. Secure

or remove loose clothing and jewelry or clothing with loosely hanging ties, straps, tassels, etc. They can be caught in moving parts.

S Being fully covered also helps protect you

from debris and pieces of toxic plants thrown by spinning line/blade.

S Stay Alert. Do not operate unit when you are

tired, ill, upset or under influence of alcohol, drugs, or medication. Watch what you are doing; use common sense.

S Wear hearing protection. S Never start or run the engine inside a

closed room or building. Breathing exhaust fumes can kill.

S Keep handles free of oil and fuel. S Always use the handlebar and a properly

adjusted shoulder strap with a blade (see ASSEMBLY).

SAFETY INFORMATION ON THE UNIT

UNIT/MAINTENANCE SAFETY

WARNING: Stop unit and disconnect

the spark plug before performing maintenance (except carburetor adjustments). S Look for and replace damaged or loose

parts before each use. Look for and repair fuel leaks before use. Keep unit in good working condition.

S Throw away blades that are bent, warped,

cracked, broken, or damaged in any other way. Replace trimmer head parts that are cracked, chipped, broken, or damaged in any other way before using the unit.

S Maintain unit according to recommended

procedures. Keep blade sharp. Keep cutting line at the proper length.

S Use onl y Poulan PRO brand replacement

line. Never use wire, rope, string, etc.

S Install required shield properly before using

theunit.Usethemetalshieldforallmetal blade use. Use the plastic shield for all line trimmer use.

S Use only specified blade or trimmer head;

make sure it is properly installed and securely fastened.

S Never start engine with clutch shroud re-

moved. The clutch can fly off and cause serious injury.

S Be sure blade or trimmer head stops turning

when engine idles.

S Make carburetor adjustments with the low-

er end supported to prevent blade or trimmer line from contacting any object. Hold unit by hand; do not use the shoulder strap for support.

S Keep others away when making carburetor

adjustments.

S Use only recommended Poulan PRO ac-

cessories and replacement parts.

S Have all maintenance and service not ex-

plained in this manual performed by your authorized service dealer.

FUEL SAFETY

S Mix and pour fuel outdoors. S Keep away from sparks or flames. S Use a container approved for fuel. S Do not smoke or allow smoking near fuel or

the unit or while using the unit.

S Avoid spilling fuel or oil. Wipe up all fuel

spills before starting engine.

S Move at least 10 feet (3 meters) away from

fueling site before starting engine.

S Stop engine and allow it to cool before re-

moving fuel cap.

S Empty the fuel tank before storing or trans-

porting the unit. Use up fuel left in the carburetor by starting the engine and letting it run until it stops.

S Store unit and fuel in area where fuel vapors

cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

S Always store gasoline in a container ap-

proved for flammable liquids.

CUTTING SAFETY

WARNING: Inspect the area to be

cut before each use. Remove objects (rocks, broken glass, nails, wire, string, etc.) which can be thrown or become entangled in the blade or trimmer head. S Keep others including children, animals,

bystanders, and helpers at least 50 feet (15 meters) away. Bystanders should be encouraged to wear safety glasses. Stop engine immediately if you are approached.

Page 5

S Always keep engine on the right--hand side

of your body.

S Hold the unit firmly with both hands. S Keep firm footing and balance. Do not over-

reach.

S Keep blade or trimmer head below waist

level. Do not raise engine above your waist.

S Keep all parts of your body away from blade,

trimmer head, and muffler when engine is running. A hot muffler can cause serious burns.

S Cut from your left to your right. Cutting on

right side of the shield will throw debris away from the operator.

S Use only in daylight or good artificial light. S Use only for jobs explained in this manual.

TRANSPORTING AND STORAGE

S Stop the unit before carrying. S Keep muffler away from your body. S Allow the engine to cool and secure the unit

before storing or transporting it in avehicle.

S Empty the fuel tank before storing or trans-

porting the unit. Use up fuel leftin the carburetor by starting the engine and letting it run until it stops.

S Store unit so the blade or line limiter blade

cannot accidentally cause injury. The unit can be hung by the shaft.

S Store unit out of reach of children.

WARNING: The engine exhaust

from this product contains chemicals known to the State of California to cause cancer,birth defects or other reproductive harm.

ASSEMBLY

CARTON CONTENTS

Check carton contents against the following list:

S Powerhead S Lower attachment (with trimmer head

installed)

S Cupped washer S Large nut for installing blades S Hex wrench S Handlebar S Bracket cover S Bracket cover screws (2) S Metal blade shield S Blade shield screws (4) S 4--point weed blade S Plastic shield S Wing nut (screwed onto plastic shield) S Shoulder strap with warning S Container of oil

WARNING: Always stop unit and dis-

connect spark plugbefore performing any assembly procedures.

WARNING: If received assembled,

repeat all steps to ensure your unit is properly assembled and all fasteners are secure. Examine parts for damage. Do not use damaged parts.

NOTE: If you need assistance or find parts

missing or damaged, call 1-800-554-6723. It is normal for the fuel filter to rattle in the empty fuel tank.

SAFETY NOTICE: Exposure to vibrations

through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti- -vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.

SPECIAL NOTICE: This unit is equipped

with a temperature limiting muffler and spark arresting screen which meets the requirements of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that many internal combus tion engines be equipped with a spark arresting screen. If you operate in a locale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. For normal homeowner use, the muffler and spark arresting screen will not require any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by your authorized service dealer.

Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.

TOOLS REQUIRED

S Hex wrench (provided) S Adjustable wrench S Phillips screwdriver

INSTALLING BRUSHCUTTER ATTACHMENT CAUTION: When installing brushcutter at-

tachment, place the unit on a flat surface for stability.

1. Loosen the coupler by turning the knob counterclockwise.

Coupler

Shipping protector

2. Remove shipping protector from coupler.

3. Remove the shaft cap from the brushcutter attachment (if present).

LOOSEN

Knob

TIGHTEN

Page 6

4. Position locking/release button of attachment into guide recess of coupler.

5. Push the attachment intothe coupler until the locking/release button snaps into the primary hole.

6. Before using the unit, tighten the knob securely by turnin g clockwise.

Coupler

WARNING: Make sure the locking/

release button is locked in the primary hole and the knob is securely tightened before operating the unit. All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual. Using the wrong hole could lead to serious injury or damage to the unit.

Upper

Shaft

Primary Hole

Guide Recess

Locking/ Release

Button

Attachment

ASSEMBLY OF SHOULDER STRAP

WARNING: Proper shoulder strap

and handlebar adjustments must be made with the engine completely stopped before using unit.

1. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist.

NOTE: A one-half twist is built in the shoul-

der strap to allow the strap to rest flat on the shoulder.

2. Adjust the strap, allowing the hook to be about 6 inches (15 cm) below the waist.

3. Fasten the strap hook to the clamp located between the trigger handle and the handlebar clamp base and lift the tool to the operating position.

4. Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation.

NOTE: It may be necessary to relocate the

shoulder strap clamp on the shaft for proper balancing of unit.

TO RELOCATE SHOULDER STRAP CLAMP:

1. Loosen and remove both clamp screws.

2. Place the upper shoulder strap clamp over the shaft.

3. Position the lower shoulder strap clamp under the shaft and align the upper and lower clamp screw holes.

Locking/Release Button in Primary Hole

For assembly of optional attachments (see list on page 10), refer to the ASSEMBLY section of the applicable attachment instruction manual.

ATTACHING THE HANDLEBAR

DANGER: To avoid serious injury, the

barrier portion of the handlebar must be installed as shown to provide a barrier between operator and the spinning blade.

1. Locate the decal on the handlebar. This decal includes an arrow. Position the handlebar with the mounting bracket at the end of the arrow.

2. Position the bracket cover over the handlebar. Again make sure the handlebar is at the end of the arrow.

3. Insert screws and hand tighten only. Be sure the handlebar is installed correctly; then, tighten each screw securely with the hex wrench.

Handlebar

Mounting Bracket

Screw

Bracket Cover

Upper Shoulder Strap Clamp

Lower Shoulder Strap Clamp

4. Insert two screws into the screw holes.

5. Secure shoulder strap clamp by tightening screws with a hex wrench.

6 inches (15 cm) below waist

Screws

ADJUSTMENT

FOR BALANCE

30 inches (76 cm)

HARNESS

4 -- 12 inches

(10 -- 30 cm)

ground

above

Page 7

30 inches (76 cm)

NOTE: If your unit has a plastic cover over

the threads on the threaded shaft, remove the covering to expose the threads. Before installing the trimmer head, make sure the dust cup and retaining washer are positioned on the gearbox as shown below.

Bracket

Slot

Wing Nut

CONFIGURING YOUR UNIT

You can configure your unit using a cutting head for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1/2 inch (1 cm) in diameter. To assemble your unit, go to the section for the desired configuration and follow the instructions.

ASSEMBLY INFORMATION -TRIMMER HEAD

TRIMMER HEAD

NOTE:Remove the blade and metal shield be-

fore attaching the plastic shield and trimmer head. To remove blade, align hole in the dust cup with the hole in the side of the gearbox by rotating the blade. Insert a small screwdriver into aligned holes. This willkeeptheshaftfrom turning while loosening the blade nut. Remove blade nut by turning clockwise. Remove the screwdriver. Remove both washers and blade. T o remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INSTALLATION OF THE METAL BLADE for illustrations. Be sure to store all parts and instructions for future use.

ATTACHING THE PLASTIC SHIELD ANDTRIMMERHEAD

WARNING: The shield must be prop-

erly installed. The shield provides partial protection to the operator and others from the risk of thrown objects, and is equipped with a line limiter blade which cuts excess line to the proper length. The line limiter blade (on underside of shield) is sharp and can cut you.

1. Remove wing nut from shield.

2. Insert bracket into slot on shield.

3. Pivot shielduntil bolt passes throughhole in bracket.

4. Tighten the wing nut securely.

Shield

NOTE: Make sure all parts are properly

installed as shown in the illustration before installing the trimmer head.

5. Align hole in the dust cup with the hole in

6. Insert a small screwdriver into aligned

Screwdriver

7. While holding the screwdriver in position,

NOTE: The retaining washer must be posi-

tioned with the raised section facing toward the gearbox.

Gearbox

Dust Cup

Retaining Washer

the side of the gearbox by rotating the dust cup.

holes. This will keep the shaft from turning while tightening trimmer head.

thread trimmer head onto the shaft in the direction shown on the decal (counterclockwise). Tighten until secure.

ASSEMBL Y INFORMATION -- WEED BLADE

WEED BLADE

NOTE: Remove the trimmer head and plastic

shield before attaching the metal shield and installing the weed blade. To remove the trimmer head, align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup. Insert a small scr ewdri v er into ali gned

Page 8

holes. This will keep the shaft from turning while loosening the trimmer head. Remove the trimmer head by turning clockwise. Remove the screwdriver. T o remove the plastic shie ld, loosen and remove wing nut. Pivot shield to release bracket from slot. See INSTALLATION O F THECUTTING HEAD and ATTACHING THE PLASTIC SHIELD for illustrations. Be sure to store all parts and instructions for future use. Never use the trimmer head with the metal blade installed.

ATTACHING THE METAL SHIELD

WARNING: The metal shield must

be properly installed on the tool anytime the tool is used witha blade. The forward tip of the metal shield helps to reduce the occurrence of blade thrust which can cause serious injury such as amputation to the operator or bystanders. Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the shaft.

1. Place the metal shield under the gearbox, and align the screw holes.

2. Install the blade and the retaining washer over the threaded shaft.

3. Make sure the raised part of the retaining washer is facing the gearbox and the raised area fits into the hole in the center of the blade.

4. Slide the blade and retaining washer onto the shaft of the gearbox.

5. Place the cupped washer onto the shaft. Make sure the cupped side of the washer is toward the blade.

6. Install the blade nut by threading onto the shaft counterclockwise.

Gearbox

Shield

Dust Cup

Threaded Shaft

Gearbox

Shield

2. Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield. T ightenevenly and securely with the hex wrench provided.

INSTALLATION OF THE METAL BLADE

WARNING: Wear protective gloves

when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving.

WARNING: Do not use any blades, or

fastening hardware other than the washers and nuts shown in the following illustrations. These parts must be provided by Poulan/WEED EATER and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others.

NOTE: The dust cup and retaining washer are

located on the gearbox shaft and not in the parts bag. All other fasteners mentioned in the following assembly steps are in the parts bag.

1. Remove the retaining washer from the threaded shaft ofthe gearbox. Leave the dust cup on the shaft.

Retaining Washer

Cupped Washer

NOTE: Make sure all parts are in place as il-

lustrated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer.

7. Align hole in dust cup with hole in side of gearbox by rotating the blade.

8. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while tightening the blade nut.

Screwdriver

9. TIghten blade nut firmly with a wrench while holding screwdriver in position.

10. Remove the screwdriver.

11. Turn blade by hand. If the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must reinstall.

NOTE: To remove blade, insert screwdriver

into aligned holes. Unthread the nut and remove parts. Be sure to store parts and instructions for future use.

Blade

Nut

Page 9

OPERATION

KNOW YOUR UNIT

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

Trimmer Head

Line Limiter Blade

Shield

Shaft

Handlebar

Coupler

Throttle Trigger

Spark Plug

Primer Bulb

ler

Blade

ON/STOP SWITCH

The ON/STOP switch is located on the trigger handle and is used to stop the engine. To stop the engine, push and release the engine ON/STOP switch.

ON/STOP Switch

PRIMER BULB

The PRIMER BULB removes air from thecarburetor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate the primer bulb by pressing it and allowing it to return to its original form.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel

information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Call 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly

when refueling.

HELPFUL TIP

Toobtain the correct oil mix ratio, pour 3.2 ounces of 2-- cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle aircooled engine oil designed to be mixed at a ratio of 40:1. Poulan/WEED EATER brand synthetic

Starter Handle

START LEVER

The START LEVER helps to supply fuel to the engine to aid in starting. Activate the starting system by moving the start lever to the START position. DO NOT squeeze the throttle trigger until the engine has started and runs. After the engine starts, allow the engine to warm-- up 10--15 seconds, then fully squeeze the throttle trigger to deactivate the starting system.

COUPLER

The COUPLER enables optional attachments to be installed on the unit.

oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 fluid ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. DO NOT USE automotive oil or marine oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

CAUTION: Never use straight gasoline in

your unit. This will cause permanent engine damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87 octane [R+M]/2 clean gasoline.

IMPORTANT

Use of alcohol blended fuels (called gasohol or using ethanol or methanol) can cause major engine performance and durability problems.

Start Lever

Page 10

WARNING: Alternative fuels (not gas-

oline) such as E--15 (15% alcohol), E -- 20 (20% alcohol), E-- 85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2-- stroke gasoline engines. Use of alternative fuels will cause problems such as: improper clutch engagements, overheating, vapor lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

HOW TO STOP YOU R UNIT

S Release the throttle trigger. S Push and release the engine ON/STOP

switch. The switch will automat i ca l l y return to the ON position. Wait 5 seconds before attempting to restart unit to allow switch to reset.

ON/STOP Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the

muffler. A hot muffler can cause serious burns.

Starting position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1--800--554--6723.

STARTING A COLD ENGINE NOTE:

DO NOT squeeze the throttle trigger

until the engine has started and runs.

1. Set unit on a flat surface.

2. Slowly press the primer bulb 6 times.

3. Move the start lever to the START position.

Primer Bulb

Start Lever

Starter Handle

4. Pull starter rope handle sharply until engine starts and runs.

5. Allow unit to run for 10--15 seconds, then fully squeeze the throttle trigger to disengage the starting system.

STARTING A WARM ENGINE

1. Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until engine runs smoothly..

3. Pull starter rope sharply while squeezing throttle trigger until engine runs.

NOTE: Normally, the warm starting proce-

dure can be used within 5--10 minutes after the unit is turned off. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under ST ARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the start lever to the RUN position. Fully squeeze throttle trigger. Pull the starter handle repeatedly while squeezing throttle trigger until engine starts and runs. This could require pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPL ER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

Edger PP1000E.....................

Cultivator PP2000T..................

Blower PP3000B....................

Pruner PP5000P....................

Pruner PP5500P....................

MODEL:

Page 11

WARNING: Always stop unit and dis-

connect spark plug before removing or installing attachments.

REMOVING TRIMMER ATTACHMENT (OR OTHER OPTIONAL ATTACHMENTS) CAUTION:

tachments, place the unit on a flat surface for stability.

1. Loosen the coupler by turning the knob counterclockwise.

Attachment

When removing or installing at-

Coupler

LOOSEN

Knob

Locking/Release Button in Primary Hole

OPERATING INSTRUCTIONS

It is recommended that the engine not be operated for longer than 1 minute at full throttle.

OPERATING POSITION

ALWAYS WEAR:

Hearing Protection

Eye Protection

TIGHTEN

2. Press and hold the locking/release button.

Locking/Release

Button

Attachment

3. While securely holding the engine and upper shaft, pull the attachment straight out of the coupler.

Coupler

Upper Shaft

INSTALLING OPTIONAL ATTACHMENTS

1. Remove the shaft cap from the attachment (if present).

2. Position locking/release button of attachment into guide recess of coupler.

3. Push the attachment intothe coupler until the locking/release button snaps into the primary hole.

4. Before using the unit, tighten the knob securely by turning clockwise.

Coupler

WARNING: Make sure the locking/

release button is locked in the primary hole and the knob is securely tightened before operating the unit. All attachments are desi gned to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual. Using the wrong hole could lead to serious injury or damage to the unit.

Upper

Shaft

Primary Hole

Guide Recess

Locking/ Release

Button

Attachment

Heavy, Long Pants

Boots

Cut from your left to your right.

When operating unit, clip shoulder strap onto clamp, stand as shown and check for the following: S Wear hearing protection, eye protection,

head protection and heavy clothing.

S Extend your left arm and hold handlebar

grip with your left hand.

S Hold throttle grip with your right hand with

finger on throttle trigger.

S Keep unit below waist level. S Keep shoulder strap pad centered on your

left shoulder and danger sign centered on your back.

S Maintain full weight of tool on your left

shoulder.

S Without bending over, keep the blade or

trimmer head near and parallel to the ground and not crowded into material being cut.

OPERATING INSTRUCTIONS FOR USE WITH TRIMMER HEAD

WARNING: Always wear eye protec-

tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury. Before trimming, bringengine to a speed sufficient to cut material to be trimmed. Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Page 12

Always release the throttle trigger and allow the engine to return to idle speed when not cutting. To stop engine:

S Release the throttle trigger. S Push and release the engine ON/STOP

switch.

CUTTING METHODS

WARNING: Use minimum speed

and do not crowd the linewhen cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head,become entangled in the line, or be thrown causing a serious hazard. S The tip of the line does the cutting. You will

achieve the best performance and minimum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below.

Tip of the line does the cutting.

Right Wrong

S The line will easily remove grass and

weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences.

S For trimming or scalping, use less than full

throttle to increase line life and decrease head wear, especially:

S During light duty cutting. S Near objects around which the line can

wrap such as small posts, trees or fence wire.

S For mowing or sweeping, usefull throttle for

a good clean job.

TRIMMING -- Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Trimming

3 inches (8 cm) above ground

SCALPING -- The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear.

Line crowded into work area.

Scalping

MOWING -- Your trimmer is ideal for mowing

in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

Mowing

SWEEPING -- The fanning action of the rotat-

ing line can be used to blow away loose debris from an area. Keep the line parallel to and above the area surface and swing the tool from side to side.

Sweeping

OPERATING INSTRUCTIONS FOR USE WITH WEED BLADE

S Blade Thrust is a reaction that only occurs

when using a bladed unit. This reaction can cause serious injury such as amputation. Carefully study this section. It is important that you understand what causes blade thrust, how you can reduce the chance of its occurring, and how you can remain in control of unit if blade thrust occurs.

S WHAT CAUSES BLAD E THRUST -- Blade

Thrust can occur when the spinning blade

contacts an object that it does not cut. This contact causes the blade to stop for an instant and then suddenly move or “thrust” away from the object that was hit. The “thrusting” reaction can be violent enough to cause the operator to be propelled in any direction and lose control of the unit. The uncontrolled unit can cause serious injury if the blade contacts the operator or others.

S WHEN BLADE THRUST OCCURS --

Blade Thrust can occur without warning if

the blade snags, stalls, or binds. This is

Page 13

more likely to occur in areas where it is difficult to see the material being cut. By using the unit properly, the occurrence of blade thrust will be reduced and the operator will be less likely to lose control.

S Cut only grass, weeds, and woody brush up

to 1/2 inch (1 cm) in diameter with the weed blade. Do not let the blade contact material it cannot cut such as stumps, rocks, fences, metal, etc., or clusters of hard, woody brush having a diameter greater than 1/2 inch (1 cm).

S Keep the blade sharp. A dull blade is more

likely to snag and thrust.

S Cut only at full throttle. The blade will have

maximum cutting power and is less likely to bind or stall.

S “Feed” the blade deliberately and not too

rapidly. The blade can thrust away if it is fed too rapidly.

S Cut only from your left to your right. Cutting on

right side of the shield will throw debris away from the operator.

S Use the shoulder strap and keep a firm grip

on the unit with both hands. A properly adjusted shoulder strap will support the weight of the unit, freeing your arms and hands to control and guide the cutting motion.

S Keep feet comfortably spread apart and

braced for a possible sudden, rapid thrust of unit. Do not overreach. Keep firm footing and balance.

S Keep blade below waist level; it will be

easier to maintain control of unit.

ADDITIONAL SAFETY RULES

FOR OPTIONAL ATTACHMENTS

S Do not raise the engineabove your waist as

the blade can come dangerously close to your body.

S Do not swing unit with such force that you

are in danger of losing your balance. Bring the engine to cutting speed before entering the material to be cut.If the blade does not turn when you squeeze the throttle trigger, make sure shaft is fully inserted into the engine. Always release the throttle trigger and allow engine to return to idle speed when not cutting. The blade should not turn while the engine is running at idle. If the blade turns at idle, do not use your unit. Refer to the CARBURETOR ADJUSTMENT section or contact your authorized service dealer. S Maintain good firm footing while using the

unit. Do this by planting feet firmly in a

comfortable apart position. S Cut while swinging the upper part of your

body from left to right. S Asyoumoveforwardtothenextareatocut,

be sure to maintain your balance and footing.

RECOMMENDED CUTTING POSITION

Cut using the 2 o’clock to 4 o’clock position of the blade

WARNING: The operator or others

must not try to clear away cut material with the engine running or the blade turning to avoid serious injury. Stop engine and blade before removing materials wrapped around blade or shaft.

2 o’clock

4 o’clock

WARNING: For each optional at-

tachment used, read entire instruction manual before use and follow all warnings and instructions in manual and on attachment.

WARNING: Ensure handlebar re-

mains installed on upper shaft (engine end of unit) at all times.

Handlebar

EDGER SAFETY

WARNING: Inspect the area to be

edged before each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by the blade or can wrap around the shaft.

WARNING: Blade rotates momen-

tarily after the trigger is released or engine is turned off. The blade can seriously cut you or others. Allow blade to stop before removing it from the cut.

S Throw away blades that are bent, warped,

cracked, broken or damaged in any other

way. Replace parts that are cracked,

chipped, or damaged before using the unit. S Do not attempt to remove cut material nor

hold material to be cut when the engine is

running or when cutting blade is moving. S Always keep the wheel and depth adjusting

skid in contact with the ground.

Page 14

S Always push the unit slowly over the

ground. Stay alert for uneven sidewalks, holes in the terrain, large roots, etc.

BLOWER/VACUUM SAFETY

WARNING: Inspect area before

starting unit. Remove all debris and hard objects such as rocks,glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation. S Do not set unit on any surface except aclean,

hard area while engine is running. Debris such as gravel, sand, dust, grass, etc., could be picked up by the air intake and thrown out through discharge opening, damaging unit, property, or causing serious injury to bystanders or operator.

S Never place objects inside the blower tubes,

vacuum tubes or blower outlet. Always direct the blowing debris away from people, animals, glass, and solid objects such as trees, automobiles, walls, etc. The force of air can cause rocks,dirt,or sticks tobe thrown or to ricochet which can hurt people or animals, break glass, or cause other damage.

S Never run unit without the proper

equipment attached. When using your unit as a blower, always install blower tubes.

S Check air intake opening, blower tubes or

vacuum tubes frequently, always with engine stopped and spark plug disconnected. Keep vents and discharge tubes free of debris which can accumulate and restrict proper air flow.

S Never place any object in air intake opening

as this could restrict proper air flow and cause damage to the unit.

S Never use for spreading chemicals, fertilizers,

or other substances which may contain toxic materials.

S To avoid spreading fire, do not use near leaf or

brush fires, fireplaces, barbecue pits, ashtrays, etc.

CULTIVATOR SAFETY

WARNING: Rotating tines can cause

serious injury. Keep away from rotating tines. Stop the engine and disconnect the spark plug before unclogging tines or making repairs.

WARNING: Inspect the area to be

cultivated before starting the unit. Remove all debris and hard and sharp objects such as rocks, vines, branches, rope, string, etc. S Avoid heavy contact with solid objects that

might stop the tines. If heavy contact occurs, stop the engine and inspect the unit for damage.

S Never operate the cultivator without the tine

cover in place and properly secured.

S Keep the tines and guard clear of debris. S After striking a foreign object, stop the

engine, disconnect the spark plug and

inspect the cultivator for damage. Repair

before restarting. S Disconnect attachment from the drive engine

before cleaning the tines with a hose and

water to remove any build--up. Oil the tines to

prevent rust. S Always wear gloves when servicing or

cleaning the tines. The tines become very

sharp from use. S Do not run unit at high speed unless

cultivating.

HEDGE TRIMMER SAFETY

DANGER: RISK OF CUT; KEEP

HANDS AW AY FROM BLADE -- Blade move s momentarily after the trigger is released or the engine is turned off. Do not attempt to clear away cut material when the blade is in motion. Make sure engine is stopped, the spark plug wire is disconnected, and the blade has stopped moving before removing jammed material from the cutting blade. Do not grab or hold the unit by the cutting blade.

WARNING: Inspect the area before

starting the unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation. S Do not use a cutting blade that is bent,

warped, cracked, broken or damaged in any

other way. Have worn or damaged parts

replaced by an authorized service dealer. S Always keep unit in front of your body.

Keep all parts of your body away from the

cutting blade. S Keep the cutting blade and airvents clear of

debris.

POLE PRUNER SAFET Y

WARNING: The reciprocating blade/

rotating chain can cause severe injury. Inspect the unit before use. Do not operate unit with a bent, cracked or dull blade or dull chain. Keep away from the blade/chain.

WARNING: The reciprocating blade/

rotating chain is sharp. Do not touch. Toprevent serious injury, always stop engine and ensure blade/chain has stopped moving, disconnect spark plug, and wear gloves when changing or handling the blade or chain.

Page 15

WARNING: A coasting blade/rotat-

ing chain cancause injury while it continues to move after the engine is stopped. Maintain proper control of the unit until the blade/chain has completely stopped moving. Keep hands, face and feet at a distance from all moving parts. Do not attempt to touch or stop the blade or chain when it is moving.

WARNING: Falling objects can

cause severe head injury. Wear head protection when operating this unit with a pole pruner attachment.

WARNING: To prevent serious injury ,

do not use more than one boom extension with a pole pruner attachment.

WARNING: Keep the pruner away

from power lines or electrical wires. S Only use for pruning limbs or branches up

to 4 inches (10 cm) in diameter.

S Do not operate the unit faster than the

speed needed to prune. Do not run the unit at high speed when not pruning.

S Always stop the unit when work is delayed

or when walking from onecutting location to another.

S If you strike or become entangled with a

foreign object, stop the engine immediately and check for damage. Have any damage repaired by an authorized service dealer before attempting further operations. Discard blades that are bent, warped, cracked or broken.

S Stop the unit immediately if you feel excessive

vibration. Vibration is a sign of trouble. Inspect thoroughly for loose nuts, bolts or damage before continuing. Contact an authorized service dealer for repair or replacement of affected parts as necessary.

SNOW THROWER SAFETY

WARNING: Keep hands and feet

away from the rotor when starting or running the engine. Never attempt to clear the rotor with the engine/motor running. Stop engine and disconnect spark plug before unclogging snow or debris from discharge chute or when adjusting vanes.

WARNING: Never lean over dis-

charge chute. Rocks or debris could be thrown into the eyes and face and cause serious injury or blindness.

WARNING: Inspect the area where

the unit is to be used. Remove objects that could be thrown or damage the unit. Some objects may be hidden by fallen snow -- be alert for the possibility. S Direct material discharge away from glass

enclosures, automobiles, etc. S Do not run engine at high speed while not

removing snow. S Be attentive when using the snowthrower,

and stay alert for holes in the terrain and other

hidden hazards. S Make sure the rotor will spin freely before

attaching the snowthrower to the powerhead. S If the rotor will not rotate freely due tofrozen

ice, thaw the unit before thoroughly before

attempting to operate under power.

S Keep the rotor clear of debris. S Do not throw snow near other people. The

snow thrower could propel small objects at

high speed causing injury. S After striking a foreign object, stop the

engine, disconnect spark plug and inspect

the snowthrower for damage and repair if

necessary before restarting unit. S Never operate the snowthrower near glass

enclosures, automobiles and trucks. S Never attempt to use the snowthrower on a

roof. S Never operate the snowthrower near

window wells, dropoffs, etc. S Never discharge snow onto public roads or

near moving traffic. S Clear snow from slopes by going up and

down; never across. Use caution when

changing directions. Never clear snow

from steep slopes. S Let snowthrower run for a few minutes after

clearing snow so moving parts do not

freeze. S Look behind and use care when backing up.

Exercise caution to avoid slipping or falling,

especially when operating in reverse. S Know how to stop quickly.

Page 16

MAINTENANCE

WARNING: Disconnect the spark

plug before performing maintenance except for carburetor adjustments.

HELPFUL TIP

IMPORTANT: Have all

repairs other than the recommended maintenance described in the instruction manual performed by an

If any dealer other than an authorized service dealer performs work on the product, Poulan PRO may not pay for repairs under warranty. It is your responsibility to maintain and perform general maintenance.

CHECK FOR LOOSE FASTENERS AND PARTS

S Spark Plug Boot S Air Filter S Housing Screws S Assist Handle Screw S Debris Shield

CHECK FOR DAMAGED OR WORN PARTS

Contact an authorized service dealer for replacement of damaged or worn parts. S ON/STOP Switch -- Ensure ON/STOP

switch functions properly by pushing and releasing the switch. Make sure engine stops. Wait 5 seconds before attempting to restart unit to allow switch to reset. Restart engine and continue.

S Fuel Tank -- Discontinue use of unit if fuel

tank shows signs of damage or leaks.

S Debris Shield -- Discontinue use of unit if

debris shield is damaged.

INSPECT AND CLEAN UNITAND DE CALS

S After each use, inspect complete unit for

loose or damaged parts. Clean the unit and decals using a damp cloth with a milddetergent.

S Wipe off unit with a clean dry cloth.

CLEAN AIR FILTER

A dirty air filter decreases engine performance and increases fuel consumption and harmful emissions. Always clean after every 5 hours of operation.

authorized service dealer.

1. Clean the cover and the area around it to

keep dirt from falling into the carburetor chamber when the cover is removed.

2. Remove parts by pressing button to re-

lease air filter cover.

NOTE: To avoid creating a fire hazard or

producing harmful evaporative emissions, do not clean filter in gasoline or other flammable solvent.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Replace parts.

Button

Air Filter

Air Filter Cover

INSPECT MUFFLER AND SPARK ARRESTING SCREEN

WARNING: The muffler on this prod-

uct contains chemicals known to the State of California to cause cancer.

As your unit is used, carbon deposits build up on the muffler and spark arresting screen and must be removed to avoid creating a fire hazard or affecting engine performance. For normal homeowner use, the muffler and spark arresting screen will not require any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by an authorized service dealer.

REPLACE SPARK PLUG

Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch (0.6 mm). Ignition timing is fixed and nonadjustable.

NOTE: This spark igniti on system complies

with the Canadian standard ICES--002.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and

discard.

3. Replace with Champion RCJ-6Y spark

plug and tighten securely with a 3/4 inch (19 mm) socket wrench.

4. Reinstall the spark plug boot.

Page 17

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

For unit to operate properly, the cutting line should be replaced when line becomes worn to less than 3 inches (7.5 cm) in le ngth from the edge of the line exit tunnels on each side of the cutting head.

1. Remove and discard worn line before installing new line.

2. Use only 0.115 inch (3 mm) diameter Poulan PRO brand cut length line.

3. Insert one end of the line through the positioning tunnel.

4. Continue to feed line through tunnel until line is centered (leaving equal amounts on each side). See illustration below.

Positioning

tunnel

5. Insert ends of line one at a time through the line exit tunnels.

6. Pull the line and make sure the line is extended fully through the tunnels.

Line exit

tunnel

7. Correctly installed line will be the same length on both ends.

BLADE REPLACEMENT

Refer to the ASSEMBLY section for blade replacement instructions and illustrations.

Line exit

tunnel

CARBURETOR IDLE SPEED ADJUSTMENT

WARNING: Keep others away when

making idle speed adjustments. The trimmer head, blade or any optional attachment will be spinning during most of this procedure. Wear your protective equipment and observe all safety precautions. After making adjustments, the trimmer head, blade or any optional attachment must not move/spin at idle speed. The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions: S Engine will not idle when the throttle is

released.

S The trimmer head, blade or optional

attachment moves/spins at idle. Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making adjustments. Keep all parts of your body away from the cutting attachment and muffler.

To adjust idle speed:

Allow engineto idle. Adjust speed until engine runs without trimmer head, blade or optional attachment moving or spinning (idle too fast) or stalling (idle speed too slow). S Turn idle speed screw clockwise to

increase engine speed if engine stalls or

dies. S Turn idle speed screw counterclockwise to

decrease engine speed if trimmer head,

blade or optional attachment moves or

spins at idle.

WARNING: Recheck the idle speed

after each adjustment. The trimmer head, blade or optional attachment must not move or spin at idle speed to avoid serious injury to the operator or others.

Idle Speed Screw

Air Filter Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

Page 18

STORAGE

WARNING: Perform the following

steps after each use: S Allow engine to cool before storing or trans-

porting.

S Store unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

S Store unit with all guards in place. Position

unit so that any sharp object cannot accidentally cause injury.

S Store unit and fuel well out of the reach of

children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more. If your unit is to be stored for a period of time: S Clean the entire unit before lengthy

storage.

S Store in a clean dry area. S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERATION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your engine. Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Follow the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will separate from the gas. We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

ENGINE

S Remove spark plug and pour 1 teaspoon of

40:1, 2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil. S Replace spark plugwith new one of recom-

mended type and heat range.

S Clean air filter. S Check entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken,

or worn parts. S At the beginning of the next season, use

only fresh fuel having the proper gasoline to

oil ratio.

OTHER

S Do not store gasoline from one season to

another. S Replace your gasoline can if itstarts to rust.

Page 19

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing allof the

recommended remedies below except remedies that require operation of the unit.

TROUBLE CAUSE REMEDY

Engine will not start.

Engine will not idle properly.

Engine will not accelerate, lacks power, or dies under a load.

Engine smokes excessively.

Engine runs hot.

1. Engine flooded.

2. Fuel tank empty.

3. Spark plug not firing.

4. Fuel not reaching carburetor.

5. Carburetor requires adjustment.

1. Carburetor requires adjustment.

2. Crankshaft seals worn.

3. Compression low.

1. Air filter dirty.

2. Spark plug fouled.

3. Carburetor requires adjustment.

4. Carbon build-up on muffler outlet screen.

5. Compression low.

1. Fuel mixture incorrect.

2. Air filter dirty.

3. Carburetor requires adjustment.

1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires adjustment.

4. Carbon build-up on muffler outlet screen.

1. See “Starting a Flooded Engine” in Operation Section.

2. Fill tank with correct fuel mixture.

3. Install new spark plug.

4. Check for dirty fuel filter; replace. Check for kinked or split fuel line; repair or replace.

5. Contact an authorized service dealer.

1. See “Carburetor Idle Speed Adjustment” in Service and Adjustments Section.

2. Contact an authorized service dealer.

3. Contact an authorized service dealer.

1. Clean or replace air filter.

2. Clean or replace plug and regap.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

5. Contact an authorized service dealer.

1. Empty fuel tank and refill with correct fuel mixture.

2. Clean or replace air filter.

3. Contact an authorized service dealer.

1. See “Fueling Engine” in Operation section.

2. Replace with correct spark plug.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

Page 20

LIMITED WARRANTY

Poulan PRO, a division of Husqvarna Consumer Outdoor Products N.A., Inc., warrants to the original consumer purchaser that each new Poulan PRO brand gasoline tool or attachment is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective gasoline product or attachment as follows from the original date of purchase. 2YEARS--Parts and Labor, when used for household purposes. 90 DAYS - - Parts and Labor, when used for commercial, professional, or income producing purposes. 30 DAYS -- Parts and Labor, if used for rental purposes. This warranty is not transferable and does not cover damage or liability caused by improper handling, improper maintenance or alteration, or the use of accessories and/or attachments not specifically recommended by Poulan PRO for this tool. This warranty does not cover tune--up, spark plugs, filters, starter ropes, cutting line, or rotating head parts that will wear and require replacement with reasonable use during the warranty period. This warranty does not cover pre-delivery setup or normal adjustments explained in the instruction manual. This warranty does not cover transportation costs. In the event you have a claim under this warranty, you must return the product to an authorized service dealer. Should you have any unanswered questions concerning this warranty, please contact: Poulan PRO, a divisio n of Husqvarna Consumer Outdoor Products N.A., Inc. 7349 Statesville Road Charlotte, NC 28269 1-- 800- -554- -6723

In Canada, contact:

Poulan PRO

850 Matheson Blvd. West Mississauga, Ontario L5V 0B4 Giving the model number, serial number and date of purchase of your product and the name and address of the authorized dealer from whom it was purchased. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MA Y HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. NO CLAIMS FOR CONSEQUENTIAL OR OTHER DAMAGES WILL BE ALLOWED, AND THERE ARE NO OTHER EXPRESS WARRANTIES EXCEPT THOSE EXPRESSLY STIPULAT ED HEREIN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMI TATI ONS O F INCI DE NTAL O R CO NSE QUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This is a limited warranty within the meaning of that term as defined in the Magnuson-- Moss Act of 1975. The policy of Poulan PRO is to continuously improve its products. Therefore, Poulan PRO reserves the right to change, modify, or discontinue models, designs, specifications, and accessories of all products at any time without notice or obligation to any purchaser.

U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U.S. Environmental

Protection Agency, California Air Resources Board, Environment Canada and Poulan PRO are pleased to explain the emissions control system warranty on your year 2010 and later small off--road engine. In California, all small off-- road engines must be designed, built, and equipped to mee t the Stat e’s stringent anti-smog standards. Poulan PRO must warrant the emission control system on your small off--road engine for the periods of time listed below provided there has been no abuse, neglect, or improper maintenance of your small off--road engine. Your emission control system includes parts such as the carburetor, the ignition system and the fuel tank. Where a warrantable condition exists, Poulan PRO will repair your small off-- road engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COV ERAGE: If anyemissions related part onyour

engine (as listed under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or replaced by Poulan PRO. OWNER’S WARRANTY RE- SPONSIBILITIES: As the small off--road engine owner, you are responsible for the performance of the required maintenance listed in your instruction manual. Poulan PRO recommends that you retain all receipts covering maintenance on your small off--road engine, but Poulan PRO cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the small off--road engine owner, you should be aware that Poulan PRO may deny you warranty coverage if your small off-road engine or a part of it has failed due to

Page 21

abuse, neglect, improper maintenance, unapproved modifications, or the use of parts not made or approved by the original equipment manufacturer. You a re responsible for presenting your small off--road engine to an Poulan PRO authorized repair center as soon as a problem exists. Warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center, call Poulan PRO at 1-- 800- -554- -6723, or send e-mail correspondence to emission.warranty@HCOP- -emission

. WARRANTY COMMENCEMENT

com DATE: The warranty period begins on the date the small off-- road engine is purchased. LENGTH OF COVERAGE: This warranty shall be for a period of two years from the initial date of purchase, or until the end of the product warranty (whichever is longer).

WHAT IS COVERED: REPAIR OR REPLACEMENT OF PARTS. Repair or replace-

ment of any warranted part will be performed at no charge to the owner at an approved Poulan PRO servicing center. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center, call Poulan PRO at 1--800-- 554-- 6723, or send e-mail correspondence to emission.warranty HCOP--emission.com Any wa rranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of “repair or replace as necessary” shall be warranted for 2 years. Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part. DIAGNOSIS: The owner shall not be charged for diagnostic labor which leads to

The information on the product label indicates which standard your engine is certified. Example: (Year) EPA and/or CALIFORNIA.

. WARRANTY PERIOD:

the determination that a warranted part is defective if the diagnostic work is performed at an approved Poulan PRO servicing center. CONSEQUENTIAL DAMAGES: Poulan PRO may be liable for damages to other engine components caused by the failure of a warranted part still under warranty. WHATIS NOT COVERED: All failures caused by abuse, neglect, or improper maintenance are not covered. ADD--ONORMODIFIED PARTS: The use of add-- on or modified parts can be grounds for disallowing a warranty claim. Poula nPRO is not liable to cover failures

of warranted parts caused by the use of add--on or modified parts. HOW TO FILE A CLAIM: If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized s ervic e center, call Poulan PRO at 1-- 800-- 554-- 6723, or send e-mail correspondence to @HCOP-- emission.com WARRANTY SERVICE: Warranty services or repairs shall be provided at all Poulan PRO service centers. Call: 1-- 800-- 554-- 6723 or send e-mail correspondence to warranty@HCOP--emission.com

NANCE, REPLACEMENT AND REPAIR OF EMISSION RELATEDPARTS: Any Pou-

lan PRO approved replacement part used in the performance of any warranty mainte-

nance or repair on emission related parts will be provided without charge to the owner if the part is under warranty. EMISSION CON- TROL WARRANTY PARTS LIST: Carburetor, air filter (covered up to maintenance schedule), ignition system: spark plug (covered up to maintenance schedule), ignition module, muffler including catalyst (if equipped), fuel tank. MAINTENANCESTATEMENT: The owner is responsible for the performance of all required maintenance as defined in the instruction manual.

emission.warranty

. WHERE TO GET

emission.

. MAINTE-

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)