Page 1
R
Please do not return product to retailer.
Por favor, no devuelva el producto al lugar de compra.
Veuillez ne pas retourner le produit au détaillant.
1--800--554--6723
Register your product online at:
Registre su producto en línea en:
Enregistrez votre produit en ligne à l’adresse :
www.poulan.com
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
1420
1630
ENGLISH ESPAÑOL
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Poulan
7349 Statesville Road
Charlotte, NC 28269
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
115259626 Rev. 2 4/15/10 BRW
Poulan
FRANÇAIS
Page 2
SAFETY RULES
WARNING: When using electric
gardening appliances, basic safety precautions must always be followed to reduce the risk of fire, electric shock, and
serious injury. Read and follow all instructions.
WARNING: Always disconnect unit
from power source when making repai r s,
adjustments, and when changing accessories and attachments such as saw bar,
chain or guards.
Because a chain saw is a high-speed
woodcutting tool, special pr ecauti ons
must be observed to reduce risk of accidents. Careless or improper use of this
tool can cause serious injury.
PLAN AHEAD
S Restrict the use of your saw to adult
users who understand and can follow
the safety rules, precautions, and operating instructions found in this
manual.
S Dress properly. Wear protective gear.
Always use steel-toed safety footwear
with non-slip soles; snug-fitting clothing; hea vy-duty, non-slip gloves; eye
protection such as non-fogging,
vented goggles or face screen; an approved safety hard hat; and sound
barriers (ear plugs or mufflers) to protect your hearing. Regular us ers
should have hearing checked regularly as chain saw noise can damage
hearing.
S Secure hair above shoulder length. Do
not wear l oose clothing or j ewel r y; they
can get caught in moving parts.
Hearing
Protection
Snug
Fitting
Clothing
Safety
Shoes
S Keep all parts of your body away from
the chain when saw is running.
S Keep children away. Do not let visitors
contact chai n saw or extension cord.All
visitors shoul d be kept at least 30 feet
(10 meters) away from work area.
S Do not handle or operate a chain saw
when you are fatigued, ill, upset, or if
you have taken alcohol, drugs, or me-
Safety Hat
Eye
Protection
Heavy Duty
Gloves
Safety Chaps
dication. You must be in good physical
condition and mentally alert. If you
have any condition that might be aggravated by strenuous work, check
with doctor before operating. Watch
what you are doing. Use common
sense.
S Do not start cutting until you have a
clear work area, secure footing, and
especially if you are felling a tree, a retreat path. Keep work area clean.
OPERATE YOUR SAW SAFELY
S Do not operatewith one hand. Serious
injury to the operator, helpers, or bystanders may result from one-handed
operation. A chain saw is intended for
two-handed use.
S Do not operate saw from a ladder or in
atree.
S Make sure thechain willnot make con-
tact with any object while starting the
saw. Never start the saw when the
guide bar is in a cut.
S Don’t force chain sa w. It will do the job
better and safer at the rate for which it
was intended.
S Do not put pressure on the saw, espe-
cially at the end of the cut. Doing so
can cause you to lose control when
the cut is completed.
S Stop the saw before setting it down.
S Hand carry saw only when motor is
stopped. Carry the chain saw by the
front handle with the saw stopped, finger
off the switch, the guide bar and saw
chain to the rear .
S Use the right tool, cut wood only.Don’t
use chain saw for purpose not intended; for example, don’t use chain
saw for cutting plastic, masonry, nonwood building materials.
S Do not operate a c hain saw that is
damaged, improperly adjusted, or not
completely and securely assembled.
Always replace bar, chain, hand
guard, or other parts immediately if
they become damaged,broken, or are
otherwise removed.
S Inspect chain saw cords periodically
and if damaged, have repaired by an
authorized service dealer.
MAINTAIN YOUR SAW IN GOOD
WORKING ORDER
S Have all chain saw servi ce performed
by an auth o rized service dealer except
the items listed in the
MAINTENANCE
section of thi s manual.
S Make certain saw chain stops moving
when trigger switch is released.
2
Page 3
S Keep the handles dry and clean and
free from oil and grease.
S Keep oil cap and fasteners securely
tightened.
S Nonconforming replacement compo-
nents or the removal of safety devices
may cause damage to the unit and possible injury to the operator or bystanders. Use only Poulan accessories and
replacement parts as recommended.
Never modify your saw.
S Maintain chain saw with care.
S Keep unit sharp and clean for better
and safer performance.
S Follow instructions for lubricating and
changing accessories.
S Unplug the chain saw from the power
source when not in use, before servicing, and when changing accessories
and att achments, such as saw chain
and guard.
S Check for damaged parts. Before fur-
ther use of the chain saw, a guard or
other part that is damaged should be
carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts,
breakage of parts, mounting and any
other condit i ons that may af f ect its operation. A guard or other part that is
damaged should be properly repaired
or replaced by an authori zed service
dealerunless otherwise indicated elsewhere in t he instruction manual.
S When not in use, chain saws should
be stored in a dry, high or locked-up
place out of the reach of children.
S When storing saw, unplug and use a
bar sheath or carrying case.
ELECTRICAL SAFETY
WARNING: A void a dangerous en-
vironment. T o reduce the ri sk of electri cal
shock, do not use in rain, in damp or wet
locations, or around swimmi ng pools, hot
tubs, etc. Do not expose to snow, rain, or
water to avoid the possibility of electrical
shock. Do not handle extension cord or
plug with wet hands.
S Use a voltage supply as shown on the
nameplate of t he unit.
S Avoid dangerous situations. Do not use
in the presence of flammable liquids or
gases to avoid creati ng a fi re or explosion and/or causing damage to uni t.
S To reduce the risk of electrical sho ck,
this appliance has a polarized plug (one
blade iswider than the other) and willrequire the use of a polarized extension
cord. The appliance plug will fit into a polarized extension cord onl y one way. If
the plug does not fit ful l y into the extension cord, re verse t he plug. If the plug
still does not fit, obtain a corr ect polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the
polarized wall outlet only one way. If
plug does not fit fully into the wall outlet,
reverse the plug. If the plug still does not
fit, contact a qualified electrician to install
the properwall outlet. Do not change the
equipment plug, extension cord receptacle, or extension cord plug in any way.
S To reduce ri sk of electrical shock, use
extension cords specifically marked as
suitable for outdoor appliances. The
electrical rating of the cord must not be
less than the rating of the unit. The cord
must be marked with suffix “W--A” (in
Canada, “W”). Use a polarized cord.
Make sure your extension cord is in
good condition. Inspect extension cord
before use and repl ace if damaged. Do
not use a damaged cord. Cord insulation must be intact with no cracks or deteriorati on. Plug connectors must be
undamaged. An undersized extension
cord will cause a drop in line voltage resultingin loss of power and overheating.
If in doubt, use the next heavier gauge.
The lower the gauge number , the heavier the cord (see
in the OPERATION sectio n). Do
CORD
SELECT AN EXTENSION
not use multiple cords.
S Do not abuse cord. Never carry the
unit by the extension cord or yank extension cord to disconnect unit.
S Secure extension cord to power cord
to prevent disconnection from unit.
S Do not use the unit if the switch does
not turn the unit on and off properly, or
if the lock--out does not work. Repairs
to the switch must be made by an
authorized service dealer.
S Keep extension cord clear of operator
and obstacles at all times. Position
cord so that it will not be caught on
branches. Do not expose cords to
heat, oil, water, or sharp edges.
S T o avoid the possibility of electric shock,
avoid b ody contact w i th any grounded
conductor, such as metal fences or
pipes.
S Ground Fault Circuit Interrupter
(GFCI) protection should be provided
on circuit or outlet to be used. Receptacles are available having built-in
GFCI protection and may be used for
this measure of safety. Inspect chain
saw cords periodically and if damaged, have repaired by an authorized
service dealer.
3
Page 4
GUARD AGAINST KICKBACK
A
v
K
Follow all safety rules to help avoid kickback and ot her forces which can result in
serious injury.
Kickback Path
oid Obstructions
Clear The Working Area
WARNING: Avoid kickback which
can result in serious injury. Kickback is
the backward, upward or s udden forward motion of the guide bar occurring
when the saw chain nearthe upper tip of
the guide bar contacts any object such
as a log or branch, or when the wood
closes in and pinches the saw chain in
the cut. Contacting a foreign object in
the wood can also result in loss of chain
saw control.
S RotationalKickbackcan occur when
the moving chain contacts an object at
the upper tip of theguide bar. This contact can cause the chain to dig into the
object, which stops the chain for an
instant. The result is a lightning fast,
reverse reaction whichkicks theguide
bar up and bac k toward the operator.
S Pinch-Kickback can occur when the
the wood closes in and pinches the
moving saw chain in the cut along the
top of the guide bar and the saw chain
is suddenly s topped. This sudden
stopping of thechain results in a reversal of the chain force used to cut wood
and causes the saw to move in the opposite direction of the chain rotation.
The saw is drivenstraight back toward
the operator.
S Pull-In canoccurwhenthemoving
chain contacts a foreign object in the
wood inthe cutalong the bottom of the
guide bar and the saw chain is suddenly stopped. This sudden stopping
pulls the saw forward and away from
the operator and could easily cause
the operator to lose controlof the saw.
REDUCE THE CHANCE OF
KICKBACK
The following precautions should be followed to minimize kickback:
S Recognize that kickback can happen.
With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
S Never let the moving chain contact
any object at the tip of the guide bar.
S Keep working area free from obstruc-
tions such as other trees, branches,
rocks, fences, s tumps, etc. Eliminate
or avoid any obstruction thatyour saw
chain could hit while cutting.
S When cutting a branch, do not let the
guide bar contact another b ranch or
other objects around it.
S Keep saw c hain sharp and properly
tensioned.A looseor dull chain can increase thechance of kickback. Follow
manufacturer’s chain sharpening and
maintenance instructions. Check tension at regularintervals, but never with
engine running. Makesure barmounting nuts are securely tightened.
S Begin and continue cutting at full
speed. If the chain is moving at a slower speed, there is greater chance of
kickback occurring.
S Use extreme caution when re-enter-
ing a cut.
S Do not attempt cuts starting with the tip
of the bar (plunge cuts).
S Watch for shifting logs or otherobjects
that could close a cut and pinch or fall
onto chain.
S Use the specified Reduced-Kickback
Guide Bar and Low Kickback Chain.
Avoid Pinch--Kickback:
S Be extremely aware of situations or ob-
structi on s that can cause materi al to
pinch the top of or otherwise stop t he
chain.
S Do notcut more than one log at a time.
S Do not twist the saw as the bar is with-
drawn from an undercut when bucking.
Avoid Pull-In :
S Always begin cutting with the saw at
full speed and the saw housing
against wood.
S Use wedges made of plastic or wood.
Never use metal to hold the cut open.
MAINTAIN CONTROL
Never Reverse
Hand Positions
Correct Position Correct Grip Incorrect Grip
eep afirm grip
with both hands,
left thumb under
4
handle
Page 5
S A good, firm grip on the saw with both
hands will help you maintain control.
Don’t let go. Grip the rear handle with
your right hand whether you are right or
left handed. Wrap the fingers of your left
hand over and around the fr ont handlebar, and your left t humb under the front
handlebar. Keep your left arm str ai ght
with the elbow locked.
S Position your left hand on the front
handlebar so it is in a straight line with
your right hand on the rear handle
when making bucking cuts. Stand
slightly to the left side of the saw to
keep your body from being in a direct
line with the cutting chain.
S Stand with your weight evenly bal-
anced on both feet.
S Do not over reach. You could be drawn
or thrown off balance and lose control .
S Do not cut above s houlder height. It is
difficult to maintain control of saw
above shoulder height.
KICKBACK SAFETY FEATURES
WARNING: The following features
are included on your saw to helpreduce
hazard of kickback; however, such features will not totally eliminate this danger. Do not rely only on safety devices.
S Hand Guard: designed to reduce the
chance of your left hand contacting
the chain if your hand slipsoff the front
handlebar.
S Position of front and rear handlebars:
designed with distance between handles and “in-line” with each other. The
spread and “in-line” position of the
hands provided by this design work together to give balance and resistance
in controlling the pivot of the saw back
toward the operator if kickback occurs.
S Reduced-Kickback Guide Bar: de-
signed with a small radius tip whichreduces the size of the kickback danger
zone on the bar tip. This type bar has
been demonstrated to significantly reduce the number and s eriousness of
kickbacks when tested in accordance
with ANSI B175.1.
Computed kickback angle (CKA) Table
MODEL
1420
1630
952044368
952044370 16″ 952051211 37_
P/N
BAR
Length
14″
Small Radius
Tip Guide Bar
Large Radius
Tip Guide Bar
S Low Kickback Chain has metkickback
performance requirements when
tested on therepresentativesample of
these chain saws specified in ANSI
B175.1.
LowKickback Chain
Contoured Depth Gauge
Elongated Guard Link
Deflects Kickback Force
And Allows Wood To
Gradually Ride Into Cutter
WARNING: Computed Kickback
Angle(CKA)listedonyoursawandlisted
in the following CKA T able represents the
angle of kickback your bar and chain
combinations will have when tested in accordance with CSA and ANSI standards.
Computedangles represented in the CKA
column indicate total energy and angle
associated without a chain brake. When
purchasing replacements, considerations
should be given to the lower CKA values.
In all cases, lowerCKA values represent a
safer operating environment f or the user.
S Tip contact in some cases may cause
a lightning fast
guide bar up and back toward the operator.
S Pinching the saw chain along the tip of
the guide bar may push the guide bar
rapidly back towards the operator.
S Either of these reactions may cause
you to lose c ontrol of the saw which
could result in serious injury. Do not
rely exclusively upon safety devices
built into your saw.
The fol lowing guide bar and chain combinations meet kickback requirements of
CSA Z62.1 & Z62.3 and ANSI B175.1
when used on saws listed in this manual .
Use of bar and chain combinations other
than those listed is not recommended and
may not meet the CKA requirements per
standard.
CHAIN P/N
952051209
REACTION,kickingthe
CKA
37_
5
Page 6
SAFETY NOTICE: Exposure to vibrations through prolonged use of hand
tools could cause blood vessel or nerve
damage in the fingers, hands, and joints
of people prone to circulation disorders
or abnormal swelling. Prolonged use in
cold weather has been linked to blood
vessel damage in otherwise healthy
people. If symptoms occur such as
numbness, pain, loss of strength,
change in skin color or texture,or loss of
feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration sys tem does not guarantee the avoidance
of these problems. Users who operate
power tools on a continual and regular
basis must closelymonitortheirphysical
condition and the condition of this tool.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insul ated to help protect against electric shock. Double insulation construction consists of two separate
“layers” of electrical insulation instead of
grounding.
Tools built with this insulation system are
not intended to be grounded. No grounding means is provided on this unit, nor
should a means of grounding be added to
this unit. As a result, t he extension cord
used withthis unitcan be plugged into any
polarized 120 volt electrical outlet.
Safety precautions must be observed
when operating any electrical tool. The
double insulation system only provides
added protection against injuryresulting
from an internal electrical insulation failure.
WARNING: All electrical repairs to
this unit, including housing, switch, motor, etc., must be diagnosed and repaired by qualified service personnel.
Replacement parts for a double insulated appliance must be identical to the
parts they replace. A double insulated
appliance is marked with the words
“double insulation” or “double insulated”. The symbol
square) may also be marked on the appliance. Failure tohave the unit repaired
by authorized service personnel can
cause the double insulation construction to become ineffective and result in
serious injury.
STANDARDS: This product is listed by
Underwriters Laboratories, Inc. in accordance with UL Standard 1662 and CSA
Standards Z62.1 and Z62.3 and ANSI
B175.1.
ANSI B175.1--2000 “American National
Standard for Powered Tools -- Saf ety Requirements”
CSA Z62.3 “Chain Saw Kickback Occupational Health and Safety”
CSA Z62.1 “Chain Saws -- Occupational
Health and Safet y”
SAVE THESE INSTRUCTIONS
(square within a
ASSEMBLY
WARNING: Before using chain
saw, ensure all fasteners are secure.
CARTON CONTENTS
S Chain Saw (fully assembled)
S Bar Sheath
Examine parts for damage. Do not use
damaged parts.
NOTE: If you need assistance or find
parts missing or damaged, please ca ll
1-800-554-6723.
ASSEMBLY
Your saw is fully assembled; no as sembly is necessary.
6
Page 7
OPERATION
KNOW YOUR SAW
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
CHAIN SAW.
location of the various controls and adjustments. Save this manual for future reference.
Compare the illustrations with your unit to familiarize yourself with the
Oiler Actuator/
Bar Oil Cap
Lock--out
Button
Chain Adjustment
Screw
Bar Sprocket
Hole
Trigger Switch
Power Cord
TRIGGER SWITCH
The
TRIGGER SWITCH is used to turn on
the unit. Squeeze the trigger switch to
operate the unit after lock--out button
has been pushed in. Releasethe trigger
to turn the unit off.
TRIGGER LOCK--OUT BUTTON
The
TRIGGER LOCK--OUT BUTTON is a
control feature designed to prevent the
motor from being accidently started.
When the rear handle is gripped in a
normal cutting position, the trigger
lock--out button can be pushed in by
the thumb, permitting the index finger
to squeeze the trigger. It is not necessary to maintain pressure on the trigger lock--out button once the trigger
has been engaged.
OPERATING INSTRUCTIONS
Use only a voltage supply as specified on
your unit.
SELECT AN EXTENSION CORD
MINIMUM WIRE GAUGE
RECOMMENDATIONS
120
25 ft.
(7.67 m)
16
A.W.G.*
Volts
*American Wire Gauge
50 ft.
(15.24 m)
16
A.W.G.*
100 ft.
(30.48 m)
14
A.W.G.*
Bar
Chain
BAR OIL CAP/OILER A CT UATOR
The
BAR OIL CAP is used to access the
bar oil tank and pressed to supply oil to
chain.
CHAIN ADJUSTMENT SCREW
CHAIN ADJUSTMENT SCREW is
The
used to adjust the c hain tension.
POWER CORD
The
POWER CORD is used to connect
the chain saw to an approved extension
cord.
CHAIN TENSION
Itis normal for a new chain to s tretch during first 15 minutes of operation. You
should check your chain tension frequently. Readjust chain after every 15
minutes of operation. See
TENSION
under the MAINTENANCE sec-
CHECK CHAIN
tion.
ATTACH THE EXTENSION CORD TO
YOUR CHAIN SAW
To prevent disconnection from unit, secure extension cord to power cord as
shown in the following illustration.
Power Cord
Extension Cord
7
Page 8
BEFORE STARTING SAW
WARNING: Be sure to read the
electricalsafety information in the
TY RULES section of this manual before
you begin. If you do not understand the
electrical safety information do not attempt to use your unit. Seek help from
someone that does understand the information or call the customer assistance help line at 1-800-554-6723.
GUIDE BAR AND CHAIN OIL
The bar and chain require lubrication. The
manually--operated chain oil er provides
lubrication to the chain and guide bar. Be
sure to fill the bar oil tank before each cutting session. The oiler activator/bar oil cap
must be used regularly and often enough
to maintain a thin fi l m of oil on the bar and
chain while saw is cutting. It is recommended that the oiler actuator/ bar oil cap
be operated every ten (10) seconds and
held for approximately three (3) seconds
SAFE-
CUTTING METHODS
each time it is presse d. For maximum
guide bar and chain life, we recomm en d
you use Poulan chain saw bar oil. If Poulan bar oil is not available, you may use a
good grade SAE 30 oil until you are able
to obtain Poulan brand. The oil output is
manually metered during operati on. Use
a funnelto fil lthe tank. Replace oil cap securely. Check oil level after every 15 minutes of operati on.
STOPPING YOUR SAW
S Release the trigger switch.
S If motor does not stop, disconnect the
extension cord. Discontinue use of
the unit until repaired by an authorized
service dealer.
STARTING YOUR SAW
1. Connect the saw to a power source
using theproper size extension cord
(see
2. Push in switch lock out button.
3. Squeeze and hold the triggerswitch.
SELECT AN EXTENSION CORD).
OPERATING TIPS
S Check chain tension before first use
and after 1 minute of operation. See
CHECK CHAIN TENSION in the MAINTE-
section.
NANCE
S Cut wood only. Do not cut metal, plas-
tics, masonry, non-wood building materials, etc.
S Stop the saw if the chain strikes a for-
eign object. Inspect thesaw an d repair
parts as necessary.
S Keep the chain o ut of dirt and sand.
Even a small amount of dirtwill quickly
dull a chain and increase the possibility of kickback.
S Practice cutting a few small logs using
the following steps. This will help you
get the “feel”of using your saw before
you begin a major sawing operation.
S Squeeze the trigge r switch and al low
unit to reach ful l speed before cutting.
S Begin cutting with the saw frame
against the log.
S Keep the motorat full speed the en-
tire time you are cutting.
S Release trigger switch as soon as cut
is completed, allowing motor to stop.
S Keep the cord away from the cutting
area. Position cord so it will not be
caught on branches and the like
during cutting.
S To avoid losing control when cut is
complete, do not put pressure on
saw at end of cut.
S Stop motor before setting saw down.
TREE FELLING TECH NIQUES
WARNING: Check for broken or
dead branches which can fallwhile cutting
causing serious injury. Do not cut near
buildings or electrical wi r es if you do not
know the directi on of tree fall, nor cut at
night since you will not be able to see well,
nor during bad weather such as rain,
snow,strongwinds,etc.Ifthetreemakes
contact with any utility line, the utility complany should be notified immediately.
S Carefully plan your sawing operation in
advance.
S Clear t he work area. You need a clear
area allaround the tree so you can have
secure footing.
S The chain saw operator should keep
on the uphill side of the terrain as the
tree is likely to roll or slide downhill af-
ter it is felled.
S Study t he natural conditions that can
cause the tree to fall in a particular direc-
tion, such as:
S The wind direction and speed.
S The lean of the tree. The lean of a tree
might not be apparent due to uneven
or sloping terrain. Use a plumb or level to determine the di r ecti on of tree
lean.
S Weight and branches on one side.
S Surrounding trees and obstacles.
S Look for decay and rot. If the trunk is
rotted, it can snap and fall toward the
operator.
8
Page 9
S Make sure there is enough room for
thetreetofall.Maintainadistanceof
2-1/2 tree lengths from the nearest per-
son or other objects. Motor noise can
drown out a warning call.
S Remove dirt, stones, loose bark, nails,
staples, and wire from the tree where
cuts are to be made.
Plan a clear retreat path
Direction of Fall
45_
FELLING LARGE TREES
(6 inches in diameter or larger)
The notch method is used to fell large
trees. A notch is cut on the side of the
tree in the desired direction of fall. After a
felling cut is made on the opposite side
of tree, the tree will tend to fall in the
direction of the notch.
NOTE: If tree h as large buttress roots,
remove them before making the notch. If
using saw to remove buttress roots,
keep saw chain from contacting ground
to prevent dulling of the chain.
NOTCH CUT AND FELLING TREE
S Make notch cut by cutting the top of
the notch first. Cut through
1/3 of the
diameter of the tree. Next complete
the notch by cuttingthe bottom. See illustration. Once notch is cut, remove
the wedge of wood from the tree.
First cut
Notch
Second cut
Felling cut here
Hinge
S After removing the wood from the
notch, make the felling cut on the opposite side of the notch. This is done
by making a cut about two inches
higher than the center of the notch.
This will leave enough uncut wood between the felling cut and the notch to
form a hinge. This hinge will help prevent the tree from falling in the wrong
direction.
Hinge holds tree on stump and helps
control fall
Opening
of felling
cut
Closing of
notch
NOTE: Before felling cut is complete, use
wedges to open the cut if necessary to
control the directi on of fall. To avoid kickback and chain damage, use wood or
plastic wedges, but never steel or iron
wedges.
S Be alert to signs that the tree is ready
to fall: cracking sounds, widening of
the felling cut, or movement in the up-
per branches.
S As tree starts to fall, stop saw, put it
down, and get away quickly on your
planned retreat path.
S
DO NOT use your saw to cut down a par-
tially fallen tree. Be extremely cautious
with partially fal l en trees that may be
poorly supported. When a tree doesn’t
fall completely, set saw aside and pull
down tree with a cable winch, block and
tackle, or tractor.
CUTTING A FALLEN TREE
(BUCKING)
Bucking is the term used for cutting a
fallen tree to the desired log size.
WARNING: Do not stand on the
log being cut. Any portion can roll ca using loss of footing and control. Do not
stand downhill of the log being cut.
IMPORTANT POINTS
S Cut only one log at a time.
S Cut shattered wood very ca refully;
sharp pieces of wood could be flung
toward operator.
S Use a sawhorse to cutsmall logs.Nev-
er allow another person to hold the log
while cutting and never hold the log
with your leg or foot.
S Do not cut in an area where logs, limbs,
and roots are tangl ed. Drag logs into a
clear area before cutting them by pulling
out exposed and cleared logs first.
BUCKING TECHNIQUES
WARNING: If saw becomes
pinched or hung in a log, don’ttry to force it
out. You can lose cont rol of the saw, resulting in injury and/or damage to the saw .
Stop the saw; drive a wedge of plastic or
wood into cut until the saw can be removed easily. Restart saw and carefully
9
Page 10
reenterthe cut. Do not usea metalwedge.
g
t
d
Do not atte m pt to restart your saw when it
is pinched or hung in a log.
Use a wedge to remove pinched saw.
S Your first cut should extend
diameter of the log.
S Finish with your second cut.
Usingalogforsupport
1/3 of the
n
2
Cut
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
Overcutting begins on the top side of
the log with the bottom of the saw
against the log. When overcutting use
light downward pressure.
Overcutting
Undercuttin
Undercutting involves cutting on the
underside of the log with top of saw
against the log. When undercutting use
light upward pressure. Hold saw firmly
and maintain control. The saw will tend
to push back toward you.
WARNING: Never turn saw upside
down to undercut. The saw cannot be
controlled in this position.
Always make your first cut on the compression side of the log. The compression side of the log is where the pressure
of the log’s weight is concentrated.
First cut on compression side of log
Second cut
Second cut
First cut on compression side of log
BUCKING WITHOUT A SUPPORT
S Overcut through
the log.
S Roll the log over and finish with a sec-
ond overcut.
S Watch for logs with a compression
side. See illustration above for cutting
logs with a compression side.
BUCKING USING A L OG OR
SUPPORT STAND
S Remember your first cut is always on
the compression side of the log. (Refer
to the illustrations for your first and
second cut)
1/3 of the diameter of
st
1
Cut
2ndCut
nd
2
1stCut
nd
Cut
Cut
1stCut
Using a support stand
2
LIMBING AND PRUNING
WARNING: Be alert for and guard
against kickback. Do not allow the moving chain to contact any other branches
or objects at the nose of the guide bar
when limbing or pruning. Allowing such
contact can result in serious injury.
WARNING: Never climb into a tree
to limb or prune. Do not s tand on ladders, platforms, a log, or in any position
which can cause you to lose your balance or control of the saw.
IMPORTANT POINTS
S Watch out for springpoles. Spring-
poles are small size limbs which can
whip toward you or pull you off b al-
ance. Use extreme caution when cut-
ting small size limbs.
S Be alert for springback from any
branches that are bent or under pres-
sure. Avoid being struck by the branch
or the saw when the tension in the
wood fibers is released.
S Frequently clear branches out of the
way to avoid tripping over them.
10
1stCu
Page 11
LIMBING
S Limb a tree only after it is cut down.
S Leave the larger limbs underneath the
felled tree to s upport the tree as you
work.
S Start at the base of the felled tree and
work toward the top, cutting branches
and limbs. Remove small limbs with
one cut.
S Keep the tree between you and the
chain.
S Remove larger branches with the cut-
ting techniques described in
WITHOUT A SUPPORT.
BUCKING
S Always use an overcut to cut small
and freely hanging limbs. Undercutting could cause limbs to fall and pinch
PRUNING
WARNING: Limit pruning to limbs
shoulder height or below. Do not cut if
branches arehigher than your shoulder.
Get a professional to do the job.
S Make your first cut
through the bottom of thelimb. T his cut
will make the limb sag so that it falls
easily on the second cut.
S Next make a second cut all the way
through the limb.
S Finish the pruning operation by using
an overcut so that the stump of the
limb protrudes 1 to 2 inches from the
trunk of the tree.
Second cut
the saw.
3rd cut 1 to 2 in.
from trunk of tree
MAINTENANCE
CUSTOMER RESPONSIBILITIES
WARNING: Disconnect power source before performing maintenance.
Fillindatesasyoucomplete
regular service
Check for damaged/worn parts
Check for loose fasteners/parts
Check chain tension
Check chain sharpness
Check guide bar
Inspect and clean unit & labels
Clean guide bar groove
Before
Use
n
n
n
n
n
n
After
Use
n
n
Every
15 min.
nCheck bar and c hain oil level
1/3 of the way
First cut
1/3 of way
Service
Dates
GENERAL RECOMMENDATIONS
The warranty on this unitdoes not c over
items thathave been subjected to operator abuse or negligence. To receive full
value from the warranty, the operator
must maintain unit as instruct- ed in this
manual. Various adjustments will need
to be made periodically to properly
maintain your unit. Improper maintenance may cause damage to the unit
and possibleinjury to the operator orbystanders.
CHECK FOR DA MAGED OR
WORN PARTS
Contact an aut hori zed service dealer for
replacement of damaged or wor n parts.
NOTE: It is normal for a small amount of
oil to appear under the saw after motor
stops. Do not confuse this witha leaking
oil tank.
S Trigger Switch -- Ensure the trigger
switch functions properly by squeez-
ing and holding the trigger switch.
Make sure motor starts and stops.
11
Page 12
S Oil Tank -- Discontinue use of chain
saw if oil tank shows signs of damage
or leaks.
S Power Cord -- Discontinue use if chain
saw power cord shows signs of damage or wear.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Bar Mounting Nut
S Chain
S Bar Adjusting Screw
CHECK CHAIN TENSION
WARNING: Wear protective
gloves when handling chain. The chain
is sharp and can cut you even when it is
not moving.
Chain tension is very important. Chain
stretches during use. This is especially
true during the firstfew tim esyou use your
saw. Always check chain tension each
time you use your saw .
1. Unplug unit from the power source.
2. Use a screwdriver to move chain
around guide bar to ensure kinks do
not exist. The chain should rotate
freely.
NOTE: It is recommended that the saw
be turned upside down for chain
tensioning.
3. Loosen bar mounting nuts until they
are finger tight.
4. Turn the adjusting screw clockwise
until the chain solidly contacts bottom of guide bar rail. Then, turn adjusting screw an additional 1/4 turn.
This is correct chain tension setting.
Adjusting Screw -- 1/4 Turn
NOTE: To tighten the chain, turn the
adjustingscrew clockwise;to loosen the
chain, turn the adjusting screw counterclockwise.
Adjusting Screw
6. Continue turning the adjusting
screw until the tension is correct
(see step 4).
7. Tighten bar mounting nuts with a
wrench.
8. Recheck chain tension.
WARNING: If the saw is operated
with a loose chain, the chain could jump
off the guide bar and result in serious injury.
CHECK CHAIN SHARPNESS
A sharp c hain makes wood chips. A dull
chain makes a sawdust powder and
cuts slowly. See
SERVICE AND ADJUSTMENTS section.
the
CHECK GUIDE BAR
Conditions which require guide bar
maintenance:
S Saw cuts to one side or at an angle.
S Saw has to be forced through the cut.
S Inadequate supply of oil to the bar and
chain.
Check the condition of the guide bar
each time the chain is sharpened. A
worn guide bar will damage the chain
and make cutting difficult.
After each use, with unit disconnected
from power source, clean all sawdust
from the guide bar and sprocket hole.
To maintain guide bar:
S Disconnect the chain saw from the
power source.
S Loosen and remove bar mounting
nuts. Remove bar, bar clamp plate
and chain from saw.
S Clean the oil holes and bar groove af-
ter each 5 hours of operation.
CHAIN SHARPENING in
Remove Sawdust From
Guide Bar Groove
5. Check the tensionby lifting the chain
fromthe guide bar. Remove some of
the stiffness in the chain by pulling
down on the chain several times.
Oil Holes
S Burring of guide bar rails is a normal
process of rail wear. Remove these
burrs with a flat file.
S When rail top is uneven, use a flat file
to restore square edges and sides.
12
Page 13
File Rail Edges
and Sides
Square
Correct GrooveWorn Groove
Replace the guide bar when the groove
is worn, the guide baris bent or cracked,
or when excess heating or burringof the
rails occurs. If replacement is necessary, use only the guide bar specified for
your saw in the repair parts list or on the
decal located on the chain saw.
LUBRICATION
Bar Oil Fill Cap
SERVICE AND ADJUSTMENTS
CHAIN SHARPENING
WARNING: Improper chain sharp-
ening techniques and/or depth gauge
maintenance wil l increase the chance of
kickback which can result in serious injury.
WARNING: Wear protective gloves
when handli ng chain. The chain is sharp
and can cut you even when it is not moving.
Conditions which indicate the need for
chain sharpening:
S Reduction in size of wood chips. The
size of the wood chip will decrease as
the chain gets duller until it becomes
more like a powder than a chip. Note
that dead or rotted wood will not produce a good chip.
S Saw cuts to one side or at an angle.
S Saw has to be forced through the cut.
Tools required:
S 5/32 inch (4 mm) diameter round file
and file holder
S Flat file
S Depth gauge tool
TO SHARPEN CHAIN:
1. Move
2. Check chain for proper tension. Ad-
3. Sharpen cutters.
ON/STOP switch to the STOP
position.
just chain tension if neces sary. See
CHECK CHAIN TENSION section.
S To sharpen the cutters, position
the file holder level (90˚) so thatit
rests on the top edges of the cutter and depth gauge.
S Check bar and chain oil before use
and every 15 minutes while operating
the saw. See
under the OPERATION section.
OIL
GUIDE BAR AND CHAIN
INSPECT AND CLEAN UNIT AND
LABELS
S After each use, inspect complete unit
for loose or damaged parts. Clean the
unit and labels us ing a damp cloth with
a mild detergent.
S Wipe off the unit and labels with a
clean dry cloth.
NOTE: The chain has both left
and right hand cutters.
File Holder
Cutter
File
90˚
Depth Gauge
S Align the 30˚ file holder marks
parallel with the ba r and to the
center of the chain.
Cutter
30˚
File Holder Line
Cutter
S Sharpen cutters on one side of the
chain first. File from the inside of
each cutter to the outside. Then,
turn the chai n saw around and repeat the process for the other side
of the chain.
S File on the forward stroke only. Use
2 or 3 strokes per cutting edge.
S Keep all cutters the same length
when filing.
S File enough to remove any dam-
age to cutting edges (side plate
and top plate of cutter).
All Cutters
Same Length
Remove Damage
Top Plate
Side Plate
13
Page 14
S File chain to meet the specifica-
f
f
tions as shown.
30˚
Hook Angle
Right
Too Much HookAngle
Wrong
80˚
0.025 inch
(0.65 mm)
Rounded
Corner
Squared O
Corner
60˚
WARNING: Maintain the proper
hook angle according t o the manufacturer’s specifi cations for the chain you are
using. Im proper hook angle will increase
the chance of kickback which can resultin
serious injury.
4. Check and lower depth gau ges.
Depth Gauge Tool
File
Itis normal for a new chain to s tretch during the first 15 minutes of operation.You
should recheck your chain tension frequently and adjust the chain tension as
required. See
CHECK CHAIN TENSION
section.
Replace the old chain when it becomes
worn or damaged. Use only the Low
Kickback replacement chain specified
in the list of available replacement parts.
The ch ain must comply with kickbackrequirementsof ANSI B175.1 when tested
with this saw.
See an authorized service d ealer to replace and sharpen individual cutters on
your chain.
TO REPLACE CHAIN:
1. Disconnect the chain saw from the
power source.
2. Turn the unit upside down on a flat
surface. Straighten out chain, then
lay it on a flat surface.
Adjusting
Screw
Bar Nuts
Depth Gauge
S Place gauge tool on cutter.
S If the depth gauge is higher than
the depth gauge tool, file it level t o
the top of the depth gauge tool.
S Maintain rounded front corner of
depth gauge with a flat file.
NOTE: The very top of the depth
gauge should be flatwith the front
half rounded off with a flat file.
If you require further assistance or are unsure about performing this procedure,
contact your authori zed service dealer or
call our customer assistance help line at
1--800--554-- 6723.
WARNING: Avoid accidentalstart-
ing. Always unplug saw from power
source before installing a bar and/or
chain.
CHAIN REPLACEMENT
WARNING: Wear protective
gloves when handling chain. The chain
is sharp and can cut you even when it is
not moving.
3. Remove bar mounting nuts, bar
clamp plate, and old chain.
4. Turn the adjusting screw counterclockwise to move the adjusting pin
almost as far as it will go to the rear.
Do not remove the adjusting screw
from the unit.
5. Hold chain with cu tters facing as
shown.
Tip of
Bar
CUTTERS MUST FACE IN
DIRECTION OF ROTATION
Cutters
Depth Gauge
Drive Links
14
Page 15
6. Slide the chain be tween the housing
and the sprocket. Place chain
around the sprocket and fit the drive
links into the guide bar groove and
then around guide bar nose.
Sprocket
Bar
Right Housing
7. Hold the guide bar against the saw
frame and install the bar c lamp plate.
Be sure the tab on the bar clamp
plate is toward the rear of bar.
Bar
Clamp
Plate
Adjusting Pin Slot
Bar Nuts
Tab
8. Secure the guide bar and bar clamp
plate with the bar nuts; tighten finger
tight only.
CAUTION: If saw chain is installed
backwards, the saw will vibrate excessively and will not cut wood.
STORAGE
CHAIN ADJUSTMENT
See
CHECK CHAIN TENSION in the MAIN-
TENANCE
section.
CUSTOMER SERVICEABLE PARTS
WARNING: Use of any other ac-
cessory or attachment might present a
risk of injury to the operator.
REPLACEMENT PART PA RT NO.
Bar Mounting Nuts 530015251
Oil Cap 530029282
Guide Plate 530029285
Safety Lock Button 530025873
Bar Adjusting Screw 530015514
Bar Adjusting Pin 530023492
Spacer 530015832
Spacer Screw 530015835
File (5/32″ dia.) T win Pak 952055085
Xtra GUARD® Chai n --14″ 952051209
Xtra GUARD® Chain -- 16″ 952051211
Lo--Kick® Guide Bar -- 14″ 952044368
Lo--Kick® Guide Bar -- 16″ 952044370
Bar & Chain Lubricant -- 1 qt. 952030129
Bar & Chain Lubricant -- 1 gal. 952030130
WARNING: Perform the following
steps after each use:
S Allow the motor to cool before storing
or transporting.
S Store chain saw and extension cord in
a well ventilated area
S Store chain saw with all guards in
place and position chain saw so that
any sharp object cannot a ccidentally
cause injury.
S Store chain sawunplugged, well out of
the reach of children.
SEASONAL STORAGE
Prepare your unit for storage at the
end of the season or if it will not be
used for 30 days or more.
If your chain saw is to be stored for a
period of time:
S Clean it thoroughly before lengthy stor-
age.
S Store in a clean dry ar ea.
S Lightly oil external metal surfaces and
guide bar.
S Oil the chain and wrap it in heavy pa-
per or cloth.
S Use bar sheath to cover bar.
15
Page 16
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power source be-
fore performing all of the recommended remedies below except remedies
that require unit to be operating.
TROUBLE CAUSE REMEDY
Chain does
not move
when trigger
switch is
engaged
Chain clatters or cuts
roughly.
Chain stops
during cut.
Oil inadequate for bar
and chain
lubrication.
Chain cuts
at an angle.
1. Chain tension incorrect.
2. Guide bar rails pinched.
3. Trigger switch failure.
.
4. Circuit breaker tripped/
fuse failure.
1. Chain tension incorrect.
2. Cutters damaged.
3. Chain worn.
4. Cutters dull, improperly
sharpened, or depth
gauges too high.
5. Sprocket worn.
1. Chain cutter tops not
filed flat.
2. Guide bar burred or
bent; rails uneven.
1. Oil tank empty.
2. Oil outlet clogged.
3. Guide bar oil hole
blocked.
1. Cutters damaged on
one side.
2. Chain dull on one side.
3. Guide bar bent or worn.
1. See “Check Chain Tension” in
Maintenance section.
2. Repair or replace.
3. Contact an authorized service
dealer.
4. Reset circuit breaker or replace
fuse.
1. See “Check Chain Tension” in
Maintenance Section.
2. Contact an authorized service
dealer.
3. Resharpen or replace chain.
4. See “Chain Sharpening” in
Service and Adjustments section.
5. Contact an authorized service
dealer.
1. See “Chain Sharpening” in
Service and Adjustments section.
2. Repair or replace guide bar.
1. Fill oil tank.
2. Contact an authorized service
dealer.
3. Remove bar and clean.
1. See “Chain Sharpening” in
Service and Adjustments section.
2. See “Chain Sharpening” in
Service and Adjustments section.
3. Replace guide bar.
16
Page 17
W ARRANTY STATEMENT
Poulan, a division of Husqvarna Con-
sumer Outdoor Products N.A., Inc.,
warrantsto the original consumer purchaser that each new Poulan brand
electricor cordless product is free from
defects in material and workmanship
and agrees to repair or replace under
this warranty any defective Poulan
brand electric product within one (1)
year from the original date of purchase.
If your Poulan brand electricor cordless
product should fail within the limited warranty period, you may return it in complete condition, prepaid, with proof of
purchase to thedealer from whom it was
purchased for repair or replacement at
the option of Poulan.
This warranty is not transferable and
does not cover damage or liability
caused by improper handling, improper
maintenance or alteration, or the use of
accessories and/or attachments not
specifically recommended by Poulan
for this product. This warranty does not
cover pa rts that will wear and require replacement with reasonable use during
the warranty period. This warranty does
not cover pre-- delivery setup or normal
adjustments explained in the instruction
manual.
Should you h ave any unans wered
questions regarding this warranty,
please contact:
Poulan, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
7349 Statesville Road
Charlotte, NC 28269
1--800--554-- 6723
In Canada, contact:
Poulan
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
Giving the model number, serial number
and date of purchase of your product and
the name and address of the authorized
dealer from whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MA Y HA VE OTHER
RIGHTS WHICH VARY FROM STATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED, AND
THERE ARE NO OTHER EXPRESS W ARRANTIES EXCEPT THOSE EXPRESSLY
STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMIT ATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
This is a limited warranty within the
meaning of that term as defined in the
Magnuson--Moss Act of 1975.
The policy of Poulan is to continuously
improve its products. Ther ef ore, Poulan
reserves the right t o change, modi fy , or
discontinue models, designs, specifi cations, and accessories of all products at
any timewithout notice or obligation toany
purchaser.
17
Loading...