Poulan Pro 115249426 Instruction Manual

ENGLISH ESPAÑOL

FRANÇAIS

WARNING:

Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le­siones graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertisse­ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.

Instruction Manual

Manual de Instrucciones

Manuel d’Ins tructions

PP033

For Occasional Use Only

R

115249426 Rev. 2 3/1/10 BRW

Poulan PRO
7349 Statesville Road
Charlotte, NC 28269

Poulan PRO

850 Matheson Blvd. West

Mississauga, Ontario L5V 0B4

Please do not return product to retailer.
Por favor, no devuelva el producto al lugar de compra.
Veuillez ne pas retourner le produit au détaillant.

1--800--554--6723

www.poulanpro.com

Register your product online at:
Registre su producto en línea en:
Enregistrez votre produit en ligne à l’adresse :

2

TABLE OF CONTENTS

Identification of Safety Symbols 2
Safety Rules 4
Assembly 9
Operation 10
Maintenance 13

Service & Adjustments 14
Storage 16
Troubleshooting Table 17
Limited Warranty Statement 18
Emissions Statement 18

IDENTIFICATION OF SAFETY SYMBOLS

WARNING: This unit can be dangerous! Careless or improper

use can cause serious injury.

DANGER: Use only specified trimmer

head, spool, and 0.080 inch (2 mm) recommended
trimmer line. Never use blades, flailing devices,
wire, rope, string, etc. This attachment is designed
for line trimmer use only. Failure to follow these
instructions may result in serious injury.

Trimmer line can throw objects violently.
You can be blinded or injured. Always
wear hearing protection and safety
glasses marked Z87. Always wear head
protection, heavy, long pants, long
sleeves, boots and gloves.

Hazard zone for thrown objects.

S Trimmer line throws objects violently.
S You and others can be blinded/injured.
S Keep children, bystanders, and animals 50 feet

(15 meters) away.

Secure hair above shoulder length. Do
not wear jewelry, loose clothing, or
clothing with loosely hanging straps,
ties, tassels, etc. They can be caught in
moving parts.

WARNING: Read the operator’s manual before use. Failure to

follow instructions could result in serious injury to the operator and/or
bystanders. Save operator’s manual.

3

IDENTIFICATION OF SAFETY SYMBOLS

When servicing unit, use only identical replacement
parts.

Never allow children to operate this unit.

Store unit indoors in a high, dry place out of the reach of
children.

Always stop unit and disconnect spark plug before clean­ing or servicing.

WARNING: Fire hazard. Never mix, pour, or store gasoline or

use the unit near a flame or sparks (including smoking, open flames, or
work that can cause sparks).

Use unleaded gasoline and two--stroke oil mixed at a ratio of
40:1 (2.5%).

Assist handle to be positioned only below
the arrow.

4

OPTIONAL ATTACHMENTS

Cutting attachment / guard,

Powerhead model Attachments Type part. no.

Trimmer head TNG 7 537419214 / 530071824

Brushcutter attachment PP4000C 952711610

Attachments Type Part. no.

Edger attachment PP1000E 952711607

Cultivator attachment PP2000T 952711608

Blower attachment PP3000B 952711609

Pruner attachment PP5000P 952711612

Pruner attachment PP5500P 952711672

These attachments used in combination with the specified powerhead have been evaluated
to applicable ISO-- and EN safety requirement standards by the Swedish Machinery Testing
Institute:

These attachments used in combination with the specified powerhead have been evaluated
to ANSI B175.3--2003, “Grass Trimmers and Brushcutters -- Safety Requirements”. These
combinations have been evaluated by Underwriter’s Laboratories Inc. (UL) and are conse­quently UL listed:

PP033

SAFETY RULES

WARNING: When using gardening

appliances, basic safety precautions must al­ways be followed to reduce the risk of fire and
serious injury. Read and follow all instructions.
This power unit can be dangerous! Operator
is responsible for following instructions and
warnings on unit and in manual. Read entire
instruction manual before using unit! Be thor­oughly familiar with the controls and the prop­er use of the unit. Restrict the use of this unit
to persons who have read, understand, and
will follow the instructions and warnings on
the unit and in the manual. Never allow chil­dren to operate this unit.

SAFETY INFORMATION

ON THE UNIT

INSTRUCTION
MANUAL

DANGER: Never use blades with line

trimmer attachment. Never use flailing de­vices with any attachment. This unit (when
used with supplied line trimmer attachment) is
designed for line trimmer use only. Use of any
other accessories with line trimmer attach­ment will increase the risk of injury.

If situations occur which are not covered in
this manual, use care and good judgment. If
you need assistance, contact your authorized
service dealer or call 1-800-554 -6723.

OPERATOR SAFE T Y

S Dress properly. Always wear safety

glasses or similar eye protection when op­erating, or performing maintenance, on

your unit (safety glasses are available).
Eye protection should be marked Z87.

S Always wear face or dust mask if operation

is dusty.

S Always wear heavy, long pants, long

sleeves, boots, and gloves. Wearing safety
leg guards is recommended.

S Always wear foot protection. Do not go

barefoot or wear sandals. Stay clear of
spinning line.

S Secure hair above shoulder length. Secure

or remove loose clothing or clothing with
loosely hanging ties, straps, tassels, etc.
They can be caught in moving parts.

S Being fully covered also helps protect you

from debris and pieces of toxic plants
thrown by spinning line.

S Stay Alert. Do not operate this unit when you

are tired, ill, upset or under the influence of al­cohol, drugs, or medication. Watch what you
are doing; use common sense.

S Wear hearing protection.
S Never start or run inside a closed room or

building. Breathing exhaust fumes can kill.

S Keep handles free of oil and fuel.
S Always keep engine on the right hand side

of your body.

S Hold the unit firmly with both hands.
S Keep trimmer head (or other optional at-

tachment) below waist level and away from
all parts of your body. Do not raise engine
above your waist.

S Keep all parts of your body away from muf-

fler and spinning line (or other optional at­tachment). Keep engine below waist level.
A hot muffler can cause serious burns.

S Keep firm footing and balance. Do not over -

reach or use from unstable surfaces such as
ladders, trees, steep slopes, rooftops, etc.

5

S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual

(or manuals for optional attachments).

UNIT / MAINTENANCE SAFETY

S Disconnect the spark plug before perform-

ing maintenance except carburetor adjust­ments.

S Look for and replace damaged or loose

parts before each use. Look for and repair
fuel leaks before use. Keep in good working
condition.

S Replace trimmer head parts that are

chipped, cracked, broken, or damaged in
any other way before using the unit.

S Maintain unit according to recommended pro-

cedures. Keep cutting line at proper length.

S Use only 0.080″ (2 mm) diameter Poulan

PRO brand line. Never use wire, rope,
string, etc.

S Install required shield properly before using

the unit. Use only specified trimmer head;
make sure it is properly installed and se­curely fastened.

S Make sure unit is assembled correctly as

shown in this manual.

S Make carburetor adjustments with lower

end supported to prevent line from contact­ing any object.

S Keep others away when making carburetor

adjustments.

S Use only recommended Poul an PRO ac-

cessories and replacement parts.

S Have all maintenance and service not ex-

plained in this manual performed by an au­thorized service dealer .

FUEL SAFETY

S Mix and pour fuel outdoors.
S Keep away from sparks or flames.
S Use a container approved for fuel.
S Do not smoke or allow smoking near fuel or

the unit.

S Avoid spilling fuel or oil. Wipe up all fuel

spills.

S Move at least 10 feet (3 meters) away from

fueling site before starting engine.

S Stop engine and allow to cool before re-

moving fuel cap.

S Always store gasoline in a container ap-

proved for flammable liquids.

TRANSPORTING AND STORAGE

S Allow engine to cool before storing or trans-

porting in vehicle.

S Empty the fuel tank before storing or trans-

porting the unit. Use up fuel left in the carbu­retor by starting the engine and letting it run
until it stops.

S Store unit and fuel in area where fuel vapors

cannot reach sparks or open flames from wa­ter heaters, electric motors or switches, fur­naces, etc.

S Store unit so line limiter blade cannot acci-

dentally cause injury. The unit can be hung
by the shaft.

S Store unit out of reach of children.

WARNING: The engine exhaust

from this product contains chemicals known
to the State of California to cause cancer, birth
defects or other reproductive harm.

SAFETY NOTICE: E xposure to vibrations

through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnor­mal swellings. Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people. If symptoms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this tool and seek medical attention. An
anti- -vibration system does not guarantee the
avoidance of these problems. Users who oper­ate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.

SPECIAL NOTICE: This unit is equipped

with a temperature limit ing muffler and spark ar­resting screen which meets the requirements of
California Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho, Maine,
Minnesota, New Jersey, Oregon, and Washing­ton require by law that many internal combus­tion engines be equipped with a spark arresting
screen. If you operate in a locale where such
regulations exist, you are legally responsible for
maintaining the operating condition of these
parts. Failure to do so is a violation of the law.
For normal homeowner use, the muffler and
spark arresting screen will not require any ser­vice. After 50 hours of use, we recommend that
your muffler be serviced or replaced by an au­thorized service dealer.

LINE TRIMMER SAFETY

WARNING: Inspect the area to be

trimmed before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by or become entangled in line.
Hard objects can damage the trimmer head
and be thrown causing serious injury.
S Keep others including children, animal s, by-

standers, and helpers at least 50 feet (15 me­ters) away. Bystanders should be encour­aged to wear safety glasses. Stop engine
immediately if you are approached.

S Use only for trimming, scalping, mowing and

sweeping. Do not use for edging, pruning or
hedge trimming.

S Cut from your right to your left. Cutting on

left side of the shield will throw debris away
from the operator.

ADDITIONAL SAFETY RULES

FOR OPTIONAL ATTAC HM ENT S

WARNING: For each optional at-

tachment used, read entire instruction manu­al before use and follow all warnings and in­structions in manual and on attachment.

WARNING: Ensure handlebar is

installed when using brushcutter attachment.
Attach handlebar above arrow on safety label
on the upper shaft (engine end of unit). If your
brushcutter attachment does not include a han­dlebar, a handlebar accessory kit (#530071451)
is available from your authorized service dealer.

6

Handlebar

EDGER SAFET Y

WARNING: Inspect the area to be

edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.

WARNING: Blade rotates momen-

tarily after the trigger is released or engine is
turned off. The blade can seriously cut you or
others. Allow blade to stop before removing it
from the cut.

S Throw away blades that are bent, warped,

cracked, broken or damaged in any other
way. Replace parts that are cracked,
chipped, or damaged before using the unit.

S Do not attempt to remove cut material nor

hold material to be cut when the engine is
running or when cutting blade is moving.

S Always keep the wheel and depth adjusting

skid in contact with the ground.

S Always push the unit slowly over the

ground. Stay alert for uneven sidewalks,
holes in the terrain, large roots, etc.

BLOWER/VACUUM SAFETY

WARNING: Inspect area before

starting unit. Remove all debris and hard ob­jects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
S Do not set unit on any surface except a

clean, hard area while engine is running.
Debris such as gravel, sand, dust, grass,
etc., could be picked up by the air intake
and thrown out through discharge opening,
damaging unit, property, or causing serious
injury to bystanders or operator.

S Never place objects inside the blower

tubes, vacuum tubes or blower outlet. Al­ways direct the blowing debris away from
people, animals, glass, and solid objects
such as trees, automobiles, walls, etc. The
forceof air can causerocks, dirt, or sticks to
be thrown or to ricochet which can hurt
people or animals, break glass, or cause
other damage.

S Never run unit without the proper equip-

ment attached. When using your unit as a
blower, always install blower tubes.

S Check air intake opening, blower tubes or

vacuum tubes frequently, always with en­gine stopped and spark plug disconnected.
Keep vents and discharge tubes free of de­bris which can accumulate and restrict
proper air flow.

S Never place any object inair intake opening

as this could restrict proper air flow and
cause damage to the unit.

S Never use for spreading chemicals, fertiliz-

ers, orother substances which may contain
toxic materials.

S Toavoid spreading fire, do not use near leaf

or brush fires, fireplaces, barbecue pits,
ashtrays, etc.

BRUSHCUTTER SAFETY

DANGER: Blade can thrust violently

away from material it does not cut. Blade
thrust can cause amputation of arms or legs.

WARNING: Do not use trimmer head

as a fastening device for the blade.

WARNING: The blade continues to

spin after the trigger is released or engine is
turned off. The coasting blade can throw ob­jects or seriously cut you if accidentally
touched. Stop the blade by contacting the
right hand side of the coasting blade with ma­terial already cut.

WARNING: Inspect the area to be

cut before each use. Remove objects (rocks,
broken glass, nails, wire, etc.) which can be
thrown or become entangled in the blade or
trimmer line.
S Throw away and replace blades that are

bent, warped, cracked, broken or damaged
in any other way.

7

S Install required shield properly before using

the unit. Use the metal shield for all metal
blade use.

WARNING: Only use brushcutter at-

tachments that provide a metal shield with
proboscis nose.

Proboscis

nose

S Use only specified bladeand make sure it is

properly installed and securely fastened.

S Cut from your left to your right. Cutting on

the right side of the shield will throw debris
away from the operator.

S Always use the handlebar and a properly

adjusted shoulder strap with blade (see AS­SEMBLY instructions in brushcutter attach­ment instruction manual).

CULTIVATOR SAFETY

WARNING: Rotating tines can cause

serious injury. Keep away from rotating tines.
Stop the engine and disconnect the spark plug
before unclogging tines or making repairs.

WARNING: Inspect the area to be

cultivated before starting theunit. Remove all
debris and hard and sharp objects such as
rocks, vines, branches, rope, string, etc.
S Avoid heavy contact with solid objects that

might stop the tines. If heavy contact oc­curs, stop the engine and inspect the unit
for damage.

S Never operate the cultivator without the tine

cover in place and properly secured.

S Keep the tines and guard clear of debris.
S After striking a foreign object, stop the en-

gine, disconnect the spark plug and inspect
the cultivator for damage. Repair before re­starting.

S Disconnect attachment from the drive en-

gine before cleaning the tines with a hose
and water to remove any build--up. Oil the
tines to prevent rust.

S Always wear gloves when servicing or

cleaning the tines. The tines become very
sharp from use.

S Do not run unit at high speed unless culti-

vating.

HEDGE T RIMMER SAFETY

DANGER: RISK OF CUT; KEEP

HANDS AWAY FROM BLADE -- Blade
moves momentarily after the trigger is re­leased or engine is turned off. Do not attempt
to clear away cut material when the blade is in
motion. Make sure the engine isturned off,the
spark plug wire is disconnected, and the
blade has stopped moving before removing
jammed material from the cutting blade. Do
not grab or hold the unit by the cutting blade.

WARNING: Inspect the area before

starting the unit. Remove all debris and hard
objects such as rocks, glass, wire, etc. that
can ricochet, be thrown, or otherwise cause
injury or damage during operation.
S Do not use a cutting blade that is bent,

warped, cracked, broken or damaged in any
other way. Have worn or damaged parts re­placed by your authorized service dealer.

S Always keep unit in front of your body.

Keep all parts of your body away from the
cutting blade.

S Keep the cutting bladeand airvents clear of

debris.

POLE PRUNER SAFETY

WARNING: The reciprocating blade/

rotating chain can cause severe injury. In­spect the unit before use. Do not operate unit
with a bent, cracked or dull blade or dull chain.
Keep away from the blade/chain.

WARNING: The reciprocating blade/

rotating chain is sharp. Do not touch. Topre­vent serious injury, always stop engine and
ensure blade/chain has stopped moving, dis­connect spark plug, and wear gloves when
changing or handling the blade or chain.

WARNING: A coasting blade/rotat-

ing chain can cause injury while it continues to
move after the engine is stopped. Maintain
proper control of the unit until the blade/chain
has completely stopped moving. Keep
hands, face and feet at a distance from all
moving parts. Do not attempt to touch or stop
the blade or chain when it is moving.

8

WARNING: Falling objects can

cause severe head injury. Wear head protec­tion when operating this unit with a pole prun­er attachment.

WARNING: To prevent serious inju-

ry, do not use more than one boom extension
with a pole pruner attachment.

WARNING: Keep the pruner away

from power lines or electrical wires.
S Only use for pruning limbs or branches up

to 6 inches (15 cm) in diameter.

S Do not operate the unit faster than the

speed needed to prune. Do not run the unit
at high speed when not pruning.

S Always stop the unit when work is delayed

or when walking from one cutting location to
another.

S If you strike or become entangled with a for-

eign object, stop the engine immediately
and check for damage. Have any damage
repaired by an authorized service dealer
before attempting further operations. Dis­card blades that are bent, warped, cracked
or broken.

S Stop the unit immediately if you feel exces-

sive vibration. Vibration is a sign of trouble.
Inspect thoroughly for loose nuts, bolts or
damage before continuing. Contact an au­thorized service dealer for repair or re­placement of affected parts as necessary.

SNOW THROWER SAFETY

WARNING: Keep hands and feet

away from the rotor when starting or running
the engine. Never attempt to clear the rotor
with the engine/motor running. Stop engine
and disconnect spark plug before unclogging
snow or debris from discharge chute or when
adjusting vanes.

WARNING: Never lean over dis-

charge chute. Rocks or debris could be
thrown into the eyes and face and cause seri­ous injury or blindness.

WARNING: Inspect the area where

the unit is to be used. Remove objects that
could be thrown or damage the unit. Some
objects may be hidden by fallen snow -- be
alert for the possibility.
S Direct material discharge away from glass

enclosures, automobiles, etc.

S Do not run engine at high speed while not

removing snow.

S Be attentive when using the snowthrower,

and stay alert for holes in the terrain and
other hidden hazards.

S Make sure the rotor will spin freely before

attaching the snowthrower to the power­head.

S If the rotor will not rotate freely due to frozen

ice, thaw the unit before thoroughly before
attempting to operate under power.

S Keep the rotor clear of debris.
S Do not throw snow near other people. The

snow thrower could propel small objects at
high speed causing injury.

S After striking a foreign object, stop the en-

gine, disconnect spark plug and inspect the
snowthrower for damage and repair if nec­essary before restarting unit.

S Never operate the snowthrower near glass

enclosures, automobiles and trucks.

S Never attempt to use the snowthrower on a

roof.

S Never operate the snowthrower near win-

dow wells, dropoffs, etc.

S Never discharge snow onto public roads or

near moving traffic.

S Clear snow from slopes by going up and

down; never across. Use caution when
changing directions. Never clear snow from
steep slopes.

S Let snowthrower run for a few minutes after

clearing snow so moving parts do not freeze.

S Look behind and use care when backing

up. Exercise caution to avoid slipping or fal­ling, especially when operating in reverse.

S Know how to stop quickly.

9

ASSEMBLY

WARNING: If received assembled,

repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.

Examine parts for damage. Do not use dam­aged parts.

NOTE: If you need assistance or find parts

missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the

empty fuel tank.
Finding fuel or oil residue on muffler is normal

due to carburetor adjustments and testing
done by the manufacturer.

INSTALLING TRIMMER ATTACH­MENT
CAUTION:

When installing trimmer attach­ment, place the unit on a flat surface for stabil­ity.

1. Loosen the coupler by turning the knob

counterclockwise.

Shipping
protector

Coupler

Knob

LOOSEN

TIGHTEN

2. Remove shipping protector from coupler.

3. Remove the shaft cap from the trimmer

attachment (if present).

4. Position locking/release button of attach-

ment into guide recess of coupler.

5. Push the attachment into the coupler until

the locking/release button snaps into the
primary hole.

6. Before using the unit, tighten the knob se-

curely by turning clockwise.

Coupler

Primary Hole

Upper

Shaft

Locking/

Release

Button

Attachment

Guide Recess

WARNING: Make sure the locking/

release button is locked in the primary hole
and the knob is securely tightened before op­erating the unit. Al l attachments are de s igned
to be used in the primary hole unless otherwise
stated in the applicable attachment instruction
manual. Using the wrong hole could lead to seri­ous injury or damage to the unit.

Locking/Release
Button in Primary Hole

For assembly of optional attachments (see
list on page 1 1), refer to the ASSEMBLY sec­tion of the applicable attachment instruction
manual.

ATTACHING SHIELD

WARNING: The shield must be prop-

erly installed. The shield provides partial protec­tion from the risk of thrown objects to the opera­tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you. For proper
orientation of shield, see KNOW YOUR TRIM­MER illustration in OPERATION section.

1. Remove wing nut from shield.

2. Insert bracket into slot as shown.

3. Pivot shield until bolt passes through hole
in bracket.

4. Securely tighten wing nut onto bolt.

Slot

Shield

Wing
nut

Bracket

Line limiter blade

ADJUSTING THE ASSIST HANDLE

WARNING: When adjusting the assist

handle, be sure it remains above the safety label
and below the mark or arrow on the shaft.

1. Loosen wing nut on handle.

2. Rotate the handle on the shaft to an up­right position; retighten wing nut.

10

OPERATION

KNOW YOUR TRIMMER

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT .
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.

Line limiter
blade

Primer bulb

Assist handle

Starter handle

Start
lever

Shield

Trimmer
head

Shaft

Muffler

ON/STOP switch

Coupler

Throttle
trigger

ON/STOP SWITCH

The ON/STOP switch is used to stop engine. To
stop the engine, push and release the engine
ON/STOP switch.

PRIMER BULB

The PRIMER BULB removes airfrom the car­buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.

START LEVER

The START LEVER helps to supply fuel to the
engine to aid in starting. Activate the starting
system by moving the start lever to the START
position. DO NOT squeeze the throttle trigger
until the engine has started and runs. After the
engine starts, allow the engine to warm--up
10--15 seconds, then fully squeeze the throttle
trigger to deactivate the starting system (start le­ver returns to RUN position).

COUPLER

The COUPLER enables optional attach­ments to be installed on the unit.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel

information in the safety rules before you begin.
If you do not understand the safety rules, do not
attempt to fuel your unit. Call 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly

when refueling.

HELPFUL TIP

T oobtain the correct oil mix
ratio, pour 3.2 ounces of
2--cycle synthetic oil into
one gallon of fresh gas.

This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle
air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/WEED EATER brand
synthetic oil is recommended. Mix gasoline and
oil at a ratio of 40:1. A 40:1 ratio is obtained by
mixing 3.2 fluid ounces (95 ml) of oil with 1 gallon

(4 liters) of unleaded gasoline. DO NOT USE
automotive oil or marine oil. These oils will
cause engine damage. When mixing fuel, follow
instructions printed on container. Once oil is
added to gasoline, shake container momentarily
to assure that the fuel is thoroughly mixed.
Always read and follow the safety rules relating
to fuel before fueling your unit.

CAUTION: Never use straight gasoline in

your unit. This will cause permanent engine
damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87
octane [R+M]/2 clean gasoline.

IMPORTANT

Use of alcohol blended fuels (called gasohol or
using ethanol or methanol) can cause major en­gine performance and durability problems.

WARNING: Alternative fuels (not gas-

oline) such as E--15 (15% alcohol), E--20 (20%
alcohol), E- -85 (85% alcohol) are NOT classified
as gasoline and are NOT approved for use in
2--stroke gasoline engines. Use of alternative
fuels will cause problems such as: improper

11

clutch engagements, overheating, vapor lock,
power loss, lubrication deficiency, deterioration
of fuel lines, gaskets and internal carburetor
components, etc. Alternative fuels cause high
moisture absorption into the fuel/oil mixture
lea ding to oil and fuel separation.

HOW TO STOP YOUR UNIT

S Release the throttle trigger.
S Push and release the engine ON/STOP

switch. The switch will auto m a t i ca l ly return to
the ON position. Wait 5 seconds before at­tempting to restart unit to allow switch to reset.

ON/STOP Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the

muffler. A hot muffler can cause serious burns.

Starting Position

HELPFUL TIP

If your engine still does not
start after following these
instructions, please call
1-- 800--554 --6723.

STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
NOTE:

DO NOT squeeze the throttle trigger

until the engine has started and runs.

1. Set unit on a flat surface.

2. Slowly press the primer bulb 6 times.

3. Move the start lever to the ST AR T position.

Muffler

Start
Lever

Starter Handle

Primer Bulb

Throttle
Trigger

4. Pull starter rope handle sharply until en­gine starts and runs.

5. Allow unit to run for 10- -15 seconds, then
fully squeeze the throttle trigger to disen­gage the starting system.

STARTING A WARM ENGINE

Pull starter rope sharply until engine starts
and runs.

NOTE: Normally, the warm starting procedure

can be used within 5 -- 10 minutes after the unit
is turned STOP . If the unit sits for more than 10
minutes without being run, it will be necessary to
start the unit by following the steps under
STARTINGACOLDENGINEorfollowingthe
starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Move the start lever to the RUN position and
fully squeeze throttle trigger. Pull the starter
handle repeatedly while squeezing throttle
trigger until engine starts and runs. This could
require pulling the starter handle many times,
depending on how badly the unit is flooded.
If the unit still doesn’t start, refer to TROUBLE­SHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are:

MODEL:

Edger PP1000E......................

Cultivator PP2000T...................

Blower PP3000B.....................

Brushcutter PP4000C.................

Pruner PP5000P.....................

Pruner PP5500P.....................

WARNING: Always stop unit and dis-

connect spark plug before removing or instal­ling attachments.

REMOVING TRIMMER ATTACH­MENT (OR OTHER OPTIONAL AT­TACHMENTS)
CAUTION:

When removing or installing at­tachments, place the unit on a flat surface for
stability.

1. Loosen the coupler by turning the knob

counterclockwise.

Attachment

Coupler

Knob

LOOSEN

TIGHTEN

2. Press and hold the locking/release button.

Locking/Release

Button

Coupler

Upper Shaft

Attachment

3. While securely holding the engine and

upper shaft, pull the attachment straight
out of the coupler.

INSTALLING OPTIONAL ATTACH­MENTS

1. Remove the shaft cap from the attach-

ment (if present).

12

2. Position locking/release button of attach­ment into guide recess of coupler.

3. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.

4. Before using the unit, tighten the knob se­curely by turning clockwise.

Coupler

Primary Hole

Upper

Shaft

Locking/

Release

Button

Attachment

Guide Recess

WARNING: Make sure the locking/

release button is locked in the primary hole
and the knob is securely tightened before op­erating the unit. Al l attachments are de s igned
to be used in the primary hole unless otherwise
stated in the applicable attachment instruction
manual. Using the wrong hole could lead to seri­ous injury or damage to the unit.

Locking/Release
Button in Primary Hole

OPERA TING INSTRUCTIONS

It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.

OPERATING POSITION

Eye protection

Long pants

Heavy shoes

ALWAYS WEAR:

Cut from your right to your left.

WARNING: Always wear eye protec-

tion. Never lean over the trimmer head.
Rocks or debris can ricochet orbe thrown into
eyes and face and cause blindness or other
serious injury.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and

vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.

To stop engine:

S Release the throttle trigger.
S Push and release the engine ON/STOP

switch.

TRIMMER LINE ADVANCE

The trimmer line will advance approximately 2
inches (5 cm) each time the bottom of the
trimmer head is tapped on the ground with the
engine running at full throttle.
The most efficient line length is the maximum
length allowed by the line limiter .
Always keep the shield in place when the tool
is being operated.
To advance line:

S Operate the engine at full throttle.
S Hold the trimmer head parallel to and above

the grassy area.

S Tap the bottom of the trimmer head lightly on

the ground one time. Approximately 2 inches

(5 cm) of line will be advanced with each tap.
Always tap the trimmer head on a grassy
area. Tapping on surfaces such as concrete
or asphalt can cause excessive wear to the
trimmer head.
If the line is worn down to 2 inches (5 cm) or
less, more than one tap will be required to ob­tain the most efficient line length.

WARNING: Use only 0.080″ (2 mm)

diameter line. Other sizes of line will not ad­vance properly and can cause serious injury.
Do not use other materials such as wire,
string, rope, etc. Wire can break off during
cutting and become a dangerous missile that
can cause serious injury.

CUTTING METHODS

WARNING: Use minimum speed

and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage thetrimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
S The tip of the line does the cutting. You will

achieve the best performance and

minimum line wear by not crowding the line

into the cutting area. The right and wrong

ways are shown below .

Tip of the line
does the cutting

Right

Line crowded Into
work area

Wrong

S The line will easily remove grass and

weeds fromaround walls, fences, trees and

flower beds, but it also can cut the tender

bark of trees or shrubs and scar fences.
S For trimming or scalping, use less than full

throttle to increase line life and decrease head

wear, especially:

13

S During light duty cutting.
S Near objects around which the line can

wrap such as small posts, trees or fence
wire.

S For mowing or sweeping, use full throttle for

a good clean job.

TRIMMING -- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.

Trimming

3 inches (8 cm)
above ground

SCALPING -- The scalping technique re­moves unwanted vegetation down to the
ground. Hold the bottom of the trimmer head
about 3 inches (8 cm) above the ground and
at an angle. Allow thetip of the line to strike the
ground around trees, posts, monuments, etc.
This technique increases line wear.

Scalping

MOWING -- Your trimmer is ideal for mowing

in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.

Mowing

SWEEPING -- The fanning action of the rotat-

ing line can be used for a quick and easy
clean up. Keep the line parallel to and above
the surfaces being swept and move the tool
from side to side.

Sweeping

MAINTENANCE

WARNING: Disconnect the spark

plug before performing maintenance except
for carburetor adjustments.

HELPFUL TIP

IMPORTANT: Have all

repairs other than the rec­ommended maintenance
described in the instruction
manual performed by an

authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, Poulan PRO may not pay for
repairs under warranty. It is your re­sponsibility to maintain and perform
general maintenance.

CHECK FOR LOOSE
FASTENERS AND PARTS

S Spark Plug Boot
S Air Filter
S Housing Screws
S Assist Handle Screw
S Debris Shield

CHECK F OR DAMAGED OR
WORN PARTS

Contact an authorized service dealer for re­placement of damaged or worn parts.
S ON/STOP Switch -- Ensure ON/STOP

switch functions properly by pushing and

releasing the switch. Make sure engine
stops. Wait 5 seconds before attempting to
restart unit to allow switch to reset. Restart
engine and continue.

S Fuel Tank -- Discontinue use of unit if fuel

tank shows signs of damage or leaks.

S Debris Shield -- Discontinue use of unit if

debris shield is damaged.

INSPECT AND CLEAN UNIT AND
LABELS

S After each use, inspect complete unit for

loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter­gent.

S Wipe off unit with a clean dry cloth.

CLEAN AIR FILTER

A dirty air filter decreases engine perform­ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.

1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.

2. Loosen knob by turning counterclock­wis e. Remove air filter cover and air filter.

NOTE: T o avoid creating a fire hazard or

producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Replace parts.

14

A

ir Filter

Air Filter Cover

Knob

MUFFLER AND SPARK ARREST­ING SCREEN

WARNING: The muffler on this prod-

uct contains chemicals known to the State of
California to cause cancer.
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen. For
normal homeowner use, however, the muffler
and spark arresting screen will not require
any service.

After 50 hours of use, we recommend that
your muffler be serviced or replaced by your
authorized service dealer .

REPLACE SPARK PLUG

Replace t he spark plug each year toensure
the engine starts easier and runs better.
Inspect s park plugevery 25 hours of usage.
Clean and/or replace asnecessary. Set spark
plug gap at 0.025 inch (0.6 mm). Ignition tim­ing is fixed and nonadjustable.

NOTE: This spark ignition system complies

with the Canadian standard ICES-- 002.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and
discard.

3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
(19 mm) socket wrench.

4. Reinstall the spark plug boot.

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

1. Press the tabs on the side of the trimmer
head and remove cover and spool.

Tab

Tab

Cover

Spool

2. Remove any remaining line.

3. Clean dirt and debris from all parts. Re­place spool if it is worn or damaged.

4. Replace with a pre-wound spool, or re­place line using a 25 feet (8 meters)
length of 0.080 inch (2 mm) diameter
Poulan PRO brand line.

WARNING: Never use wire, rope,

string, etc., which can break off and become a
dangerous missile.

5. When installing new line on an existing
spool, hold the spool as shown.

6. Bend the line at the midpoint and insert
the bend into the slot in the center rim of
the spool. Ensure line snaps into position
in the slot.

15

Slot

7. With your finger between the lines, wrap
the lines evenly and firmly around the
spool in a clockwise direction.

8. Position the lines in the guide slots.

Guide slot

Guide slot

9. Place the spool in the cover as shown
below.

10. Insert the ends of the lines through exit
holes in the sides of the cover.

Line exit hole

Cover

11. Reinstall the spool and cover onto the
trimmer head. Push untilcover snaps into
place.

16

REPLACING THE TRIMMER HEAD

1. Hold the dust cup with a wrench to keep
the shaft from turning while removing and
installing trimmer head.

Dust Cup

2. Remove trimmer head by turning coun­terclockwise (looking from bottom of
unit).

3. Thread replacement trimmer head onto the
shaft by turning clockwise. Only tighten

hand tight!

CARBURETOR IDLE SPEED
ADJUSTMENT

WARNING: Keep others away when

making idle speed adjustments. The trimmer
head or any optional attachment will be spin­ning during most of this procedure. Wearyour
protective equipment and observe all safety
precautions. After making adjustments, the
trimmer head or any optional attachment
must not move/spin at idle speed.

The carburetor has been carefully set at the
factory. Adjustments may be necessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is

released.

S The trimmer head or any optional

attachment moves/spins at idle.

Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making ad­justments. Keep all parts of your body away
from the cutting attachment and muffler.

To adjust idle speed:

Allow engine to idle. Adjust speed until engine
runs without trimmer head or any optional at­tachment moving or spinning (idle too fast) or
engine stalling (idle speed too slow).
S Turn idle speed screw clockwise to increase

engine speed if engine stalls or dies.

S Turn idle speed screw counterclockwise to

decrease engine speed if trimmer head or any
optional attachment moves or spins at idle.

WARNING: Recheck the idle speed

after each adjustment. The trimmer head or
any optional attachment must not move or
spin at idle speed toavoid serious injury to the
operator or others.

Air Filter
Cover

Idle Speed Screw

If you require further assistance or are unsure
about performing this procedure, contact an
authorized service dealer or call
1-- 800--554--6723.

STORAGE

WARNING: Perform the following

steps after each use:
S Allow engine to cool before storing or trans-

porting.

S Store unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.

S Store unit with all guards in place. Position

unit so that any sharp object cannot acci­dentally cause injury.

S Store unit and fuel well out of the reach of

children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if
it will not be used for 30 days or more.

If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy

storage.

S Store in a clean dry area.
S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA­TION section of this manual, see message la­beled IMPORTANT regarding the use of ga­sohol in your engine.

Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container.

Follow the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.

17

HELPFUL TIP

During storage of your gas/
oil mixture, the oil will sepa­rate from the gas.
We recommend that you
shake the gas can weekly
to insure proper blending of
the gas and oil.

ENGINE

S Remove spark plug and pour 1 teaspoon of

40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.

S Replace spark plug with new one of recom-

mended type and heat range.

S Clean air filter.
S Check entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken,
or worn parts.

S At the beginning of the next season, use

only fresh fuel having the proper gasoline to
oil ratio.

OTHER

S Do not store gasoline from one season to

another.

S Replace your gasoline can if it starts to rust.

TROUBLE CAUSE REMEDY

Engine will not
start.

1. Engine flooded.

2. Fuel tank empty.

3. Spark plug not firing.

4. Fuel not reaching
carburetor.

5. Carburetor requires
adjustment.

1. See “Starting a Flooded Engine” in
Operation Section.

2. Fill tank with correct fuel mixture.

3. Install new spark plug.

4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.

5. Contact an authorized service dealer.

Engine will
not idle
properly.

1. Carburetor requires
adjustment.

2. Crankshaft seals worn.

3. Compression low.

1. See “Carburetor Idle Speed Adjustment”
in Service and Adjustments Section.

2. Contact an authorized service dealer.

3. Contact an authorized service dealer.

1. Air filter dirty.

2. Spark plug fouled.

3. Carburetor requires
adjustment.

4. Carbon build-up on
muffler outlet screen.

5. Compression low.

Engine will not
accelerate,
lacks power,
or dies under
a load.

1. Clean or replace air filter.

2. Clean or replace plug
and regap.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

5. Contact an authorized service dealer.

Engine
smokes
excessively.

1. Fuel mixture incorrect.

2. Air filter dirty.

3. Carburetor requires
adjustment.

1. Empty fuel tank and refill with
correct fuel mixture.

2. Clean or replace air filter.

3. Contact an authorized service dealer.

Engine runs
hot.

1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires
adjustment.

4. Carbon build-up on
muffler outlet screen.

1. See “Fueling Engine” in Operation
section.

2. Replace with correct spark plug.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

WARNING: Always stop unitand disconnect spark plug before performing all of the

recommended remedies below except remedies that require operation of the unit.

TROUBLESHOOTING TABLE

18

LIMITED WARRANTY

Poulan PRO, a division of Husqvarna
Consumer Outdoor Products N.A., Inc., war­rants to the original consumer purchaser that
each new Poulan PRO brand gasoline tool or
attachment is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline prod­uct or attachment as follows from the original
date of purchase.
2YEARS--Parts and Labor, when used for
household purposes.
90 DAYS -- Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DA YS -- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or alteration, or
the use of accessories and/or attachments not
specifically recommended by Poulan PRO for
this tool. This warranty does not cover tune- -up,
spark plugs, filters, starter ropes, cutting line, or
rotating head parts that will wear and require re­placement with reasonable use during the war­ranty period. This warranty does not cover pre-­delivery setup or normal adjustments explained
in the instruction manual. This warranty does
not cover transportation costs.
In the event you have a claim under this warran­ty, you must return the product to an authorized
service dealer.
Should you have any unanswered questions
concerning this warranty, please contact:
Poulan PRO, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
7349 Statesville Road
Charlotte, NC 28269
1--800-- 554- -6723

In Canada, contact:

Poulan PRO

850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHT S,AND YOU MAY HAV E OTH­ER RIGHTS WHICH VAR Y FROM ST ATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX­PRESSLY STIPULATED HEREIN.
SOME STA TES DO NOT ALLOW LIMIT A­TIONS ON HOW LONG AN IMPLIED W AR­RANTY LASTS OR THE EXCLUSION OR
LIMI TATIO NS OF IN CIDENTAL OR CONS E ­QUENTIAL DAMAGES, SO THE ABOVE LIM­ITATIONS OR EXCLUSION MA Y NOT APPLY
TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson- -Moss Act
of 1975.
The policy of Poulan PRO is to continuously
improve its products. Therefore, Poulan PRO
reserves the right to change, modify, or dis­continue models, designs, specifications,
and accessories of all products at any time
without notice or obligation to any purchaser.

U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OB­LIGATIONS: The U.S. Environmental

Protection Agency, California Air Resources
Board, Environment Canada and Poulan
PRO are pleased to explain the emissions con­trol system warranty on your year 2010 and lat­er small off-- road engine. In California, all small
off--road engines must be designed, built, and
equ ipped to meet the Stat e’s stringent anti-­smog standards. Poulan PRO must warrant
the emission control system on your small
off--road engine for the periods of time listed
below provided there has been no abuse, ne­glect, or improper maintenance of your small
off--road engine. Your emission control system
includes parts such as the carburetor, the igni­tion system and the fuel tank. Where a warrant­able condition exists, Poulan PRO will repair
your small off-- road engine at no cost to you.
Expenses covered under warranty include
diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COV­ERAGE: If any emissions related part on your

engine (as listed under Emissions Control
Warranty Parts List) is defective or a defect in
the materials or workmanship of the engine
causes the failure of such an emission related
part, the part will be repaired or replaced by
Poulan PRO. OWNER’S WARRANTY RE-
SPONSIBILITIES: As the small off-- road en­gine owner, you are responsible for the per­formance of the required maintenance listed
in your instruction manual. Poulan PRO rec­ommends that you retain all receipts covering
maintenance on your small off--road engine,
but Poulan PRO cannot deny warranty solely
for the lack of receipts or for your failure to en­sure the performance of all scheduled main­tenance. As the small off--road engine owner,
you should be aware that Poulan PRO may
deny you warranty coverage if your small off-­road engine or a part of it has failed due to

19

abuse, neglect, improper maintenance, un­approved modifications, or the use of parts
not made or approved by the original equip­ment manufacturer. You are responsible for
presenting your small off- -road engine to an
Poulan PRO authorized repair center as soon
as a problem exists. Warranty repairs should be
completed in a reasonable amount of time, not
to exceed 30 days. If you have any questions
regarding your warranty rights and responsibili­ties, you should contact your nearest authorized
service center, call Poulan PRO at
1--800-- 554- -6723, or send e-mail correspond­ence to emission.warranty@HCOP--emission

.

com

. WARRANTY COMMENCEMENT

DAT E: The warranty period begins on the date
the small off--road engine is purchased.
LENGTH OF COVERAGE: This warranty
shall be for a period of two years from the ini­tial date of purchase, or until the end of the
product warranty (whichever is longer).

WHAT IS COVERED: REPAIR OR RE­PLACEMENT OF PARTS. Repair or replace-

ment of any warranted part will be performed at
no charge to the owner at an approved Poulan
PRO servicing center. If you have any ques­tions regarding your warranty rights and re­sponsibilities, you should contact your near­est authorized service center, call Poulan
PRO at 1--800--554-- 6723, or send e-mail cor­respondence to emission.war

ranty@HCOP--

emission.com

. WARRANTY PERIOD: Any

warr anted part which is not scheduled for re­placement as required maintenance, or which
is scheduled only for regular inspection to the
effect of “repair or replace as necessary” shall
be warranted for 2 years. Any warranted part
which is scheduled for replacement as re­quired maintenance shall be warranted for the
period of time up to the first scheduled re­placement point for that part. DIAGNOSIS:
The owner shall not be charged for diagnostic
labor which leads to the determination that a

warranted part is defective if the diagnostic
work is performed at an approved Poulan
PRO servicing center. CONSEQUENTIAL
DAMAGES: Poulan PRO may be liable for
damages to other engine components
caused by the failure of a warranted part still
under warranty. WHAT IS NOT COVERED:
All failures caused by abuse, neglect, or im­proper maintenance are not covered. ADD--
ON OR MODIFIED PARTS: The use of add-­on or modified parts can be grounds for
disallowing a warranty claim. Poulan PRO is
not liable to cover failures of warranted parts
caused by the use of add--on or modified parts.
HOW TO FILE A CLAIM: If you have any
questions regarding your warranty rights and
responsibilities, you should contact your
nearest authorized service center, call Pou­lan PRO at 1--800-- 554--6723, or send e-mail
correspondence to

emission.warranty@

HCOP--emission. com

. WHERE TO GET

WARRANTY SERVICE: Warranty services
or repairs shall be provided at all Poulan PRO
service centers. Call: 1--800--554--6723 or
send e-mail correspondence to

emission.

[e-mail]

. MAINTE -

NANCE, REPLACEMENT AND REPAIR OF
EMISSION RELATED PARTS: Any Poulan

PRO approved replacement part used in the
performance of any warranty maintenance or
repair on emission related parts will be pro­vided without charge to the owner if the part is
under warranty. EMISSION CONTROL
WARRANTY PARTS LIST: Carburetor, air fil­ter (covered up to maintenance schedule), igni­tion system: spark plug (covered up to mainte­nance schedule), ignition module, muffler
including catalyst (if equipped), fuel tank.
MAINTENANCESTATEMENT: The owner is
responsible for the performance of all re­quired maintenance as defined in the instruc­tion manual.

The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA and/or CALIFORNIA.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)