pottery barn kids
SCHOOLHOUSE 2 SHELF BOOKCASE
IMPORTANT SAFETY INSTRUCTIONS:
Please read all instructions carefully before assembling.
For your safety, assembly by two people is recommended.
PRE-ASSEMBLY:
• Remove all parts and hardware from the box and lay out on a clean, carpeted, or scratch-free work
surface, as this will avoid damaging any parts during assembly. The shipping box provides an ideal work
surface. Do not dispose of any contents until assembly is completed to avoid accidentally discarding small
parts or hardware.
• Use the parts and hardware lists above to identify and separate each of the pieces included.
• The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
• Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may
cause the bolts to misalign during assembly.
• If using power tools to aid in assembly please use caution. Power tools can damage hardware or split
wood.
ASSEMBLY INSTRUCTIONS:
1. Align and connect pre-drilled holes on the Left/Right Side Panel (A & B) to wooden dowels on the Center
Shelf (D) and Lower Stretcher (C). Make sue the slots on each panel are facing each other. (Fig. 1)
2. Align and connect the pre-drilled holes on the Base (E) to the wooden dowels on the assembled piece.
Insert (4) Long Bolt (I), Spring Washer (K) and Flat Washer (L) from bottom of the Base (E) to the predrilled holes on bottom of the side panel. (Fig. 2)
A.
PARTS INCLUDED:
(A) Left Side Panel – 1pc
(B) Right Side Panel – 1pc
(C) Lower Stretcher – 1pc
(D) Center Shelf – 1pc
(E) Base – 1pc
(F) Back Panel – 1pc
(G) Top Panel – 1pc
TOOLS REQUIRED:
Phillips Screwdriver
HARDWARE LIST
(H) Allen Key
- 1pc
(I) Long Bolt ¼“ x 50mm - 4pcs
(J) Short Bolt ¼“ x 30mm
- 4pcs
(K) Spring Washer 1/4“ - 8pcs
(L) Flat Washer 1/4“
- 8pcs
(M) Wood Screw 3.5 x 20mm - 3pcs
(Not included)
C.
D.
(Fig. 1)
L.
K.
I.
B.
E.
(Fig. 2)
H.
3. Upright the assembled piece. Slide the Back Panel (F) into slots on the Left/Right Side Panel. (Fig. 3)
4. Place the Top Panel (G) on the assembled piece. Insert (4) Short Bolt (J), Spring Washer (K) and Flat
Washer (L) from re-drilled holes on the Left/Right Side Panel (A & B) to the holes on bottom of the Top
Panel. (F0g. 4)
F.
G.
L.
K.
J.
H.
(Fig. 3)
5. Insert (3) Wood Screw (M) from the pre- drilled holes on the Back Panel (F) to the Center Shelf (D) to
secure the Back Panel (F). (Fig. 5)
(Fig. 4)
M.
6. Check alignment and tighten all bolts and scre ws.
CARE INSTRUCTIONS:
• Dust with a clean, soft cloth.
• Bolt spills immediately, and wipe with a clean, damp, cloth.
• We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered
finish.
Thank you for your purchase
stores | catalog | www.potterybarnkids.com
USA 1.800.290.8181
pottery barn kids
TIP RESTRAINT KIT
WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision.
Young children may be injured by tipping furniture and the use of a tipping restraint is highly recomm ended.
When properly installed, this restraint could provide protection against the unexpected tipping of furniture. We
recommend mounting this restraint to a wall stud.
All Parts and Hardware are included with the Cameron Wall Cubby.
PARTS INCLUDED
(N) Plastic Restraint
(O) Plastic Wall Brackets
Note: For safe mounting it is essential to use the proper hardware for your wall type. The included hardware is
for drywall or stud mounting only. For other wall types (ie: plaster, concrete, brick…) please consult your
local hardware store.
1. Locate a wall stud behind your furniture. Position a bracket on the stud approximately 1” below the top of the
furniture. Mark and drill pilot hole into the center of the stud with a 3/32” drill bit. Attach a bracket to the stud
with the long screws provided.
2. On the back of the furniture, a bracket will need to be attached to the furniture frame at the top. To do this,
temporarily move the furniture into its final position and mark the location of the wall bracket on the furniture
frame. Move the furniture away from the wall and place a bracket on the mark. Mark and drill holes for
screws with 3/32” drill bit. Attach the bracket to the furniture with the short screws provided.
3. Move the furniture into this final position, taking care to line up the wall bracket with the furniture bracket.
Thread a strap through the bracket as shown in the illustration. Tighten strap until snug. Do not over
tighten.
- 1pc
- 2pcs
HARDWARE NEEDED
(P) Long Screws 3x32mm
(Q) Short Screws 3x19mm
Plastic wall bracket
- 2pcs
- 2pcs
Long wood screw
Short wood screw
Plastic Restraint
Thank you for your purchase.
stores | catalog | www.potterybarnkids.com
USA 1.800.290.8181
Loading...