pottery barn kids
PUZZLE WALL SINGLE CUBBY WITH DOOR
PRE-ASSEMBLY:
•
Read all instructions before beginning assembly. The illustrations provided allow for easier assembly when used in
conjunction with the assembly instructions.
•
For your safety and ease, assembly by two adults is recommended.
•
Remove all parts and hardware from the box and lay out on a clean, carpeted, or scratch- free work surface.
Use care as some par ts or hardware may have sharp points or edges .
•
Do not dispose of any contents unt i l asse m bl y is com ple t ed to avoi d acc i dental l y discarding small
parts and hardware.
•
Use the parts and hardware lists to identify and separate each of the pieces included.
•
Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the bolts
misalign during assembly.
•
The use of power tools for assembly is not recommended. Power tools can damage hardware or split wood
P AR T S INCLUDED:
(A) Top End panel (1)
(AA) Bottom End panel (1)
(B) Right Side panel (1)
(BB) Left Side panel
(with pre-drilled holes for door)(1)
(C) Door (1)
(D) Back panel (1)
P ARTS AND HARDW ARE REQUIRED (Pack aged Separately):
Double-Wide and/or Triple-Wide Bases
Base Screws:
o Double Wide Bases include:
(8) Screws- 8 X 1”
o Triple-Wide Bases include:
TOOLS REQUIRED: (not included)
Phillips head screwdriver
(12) Screws- 8 X 1”
CUBBY HARDWARE ENCLOSED
(E) LONG SCREW-8X 1” (10)
(F) CAM LOCK (8)
(G) CAM LOCK BO LT (8)
(H) WOOD DOWEL (8)
(I) WOOD SCREW-3x15mm (4).
(J) ESPRESSO STICKER-22mm (8)
CONNECTING HARDWARE ENCLOSED:
(a): U PLATE(2)
(b): SHORT SCREW-8X3/4” (8)
Page 1/5
ASSEMBLY INSTRUCTIONS:
1. Insert (4) Wood Dowels (H) into the pre-drilled holes on the Side Panels (B) and (BB) (Figure 1). Then, fasten the (4)
Cam Lock Bolts (G) into the predrilled holes in Top Panel (A) and Bottom Pan el (AA), using the Phillip s Head Screwdriver
as shown in Figure 2. Do not over tighten the Cam Lock Bolts or the Cam Locks will not properly engage in
Steps 2 and 3.
BB
B
A
A
2. Attach the Right Side Panel (B) and Left Side Panel (BB) onto Bo t t o m End Panel (AA), as shown.
Insert Cam Lock (F) into the corresponding holes on the Side Panels (B) and (BB) and tighten using
Phillips Head Screwdriver. (Figure 3)
3. Insert the B ack panel (D) through the U-groove on the Side panels (B) and (BB) (Figure 4). Place the Top End
Panel (A) onto the semi-assembled base, as shown. Insert the Cam Lock (F) into the corresponding
pre-drilled holes on the Side Panels (B) and (BB), then use Phillips screwdriver to fasten (Figure 5).
Figure 1 Figure 2
D
B
B
Figure 3 Figure 4 Figure 5
B
B
A
A
4. Use the Phillips screwd river to tighten all the Cam Locks. If desired, use the (8) Espresso Sticker (J) to cover
the Cam Locks.
Page 2/5
5. Secure the Back Panel (D) with (10) Long Screw s (E), using the Phillip s Head Screwdriver (not incl uded) (Figure 6).
6. Attach the Door (C) to the Left Side Panel (BB), with (4) Wood Screws (I), using the Phillips Head Screwdriver (not
included).
BACK VIEW
Figure 6
A
A
( Figure 7).
Page 3/5
COMPLETING THE ASSEMBL Y:
Your Puzzle Wall System contains a set of individual components that can be attached together in a variety
of combinations to suit your own space. To assemble the set together, please follow these steps:
1.
Choose your preferred layout by arranging the Puzzle Wall Cubbies together as desired, atop the Bases
(packaged separately). If needed, loosen or tighten the adjustable levers on the underside of the Bases to
ensure
that your system will sit firmly on the ground.
BASE
Rig ht
Left
2.
Turn pieces upside down and fasten the Bases to the Bottom Cubbies using the 8 X 1” screws, as shown
below.
BASE
Fasten from the underside of
the Base through the underside
of
the Cubby
Page 4/5
3.
Attach the individual Puzzle Components together by fastening the U Plates (a) with (4) Screws (b) each along
back edges, as shown below, using the Phillips Head Screwdriver (not included).
the
BACK VIEW
As a safety precaution, please follow the instructions enclosed to secure the Puzzle Wall Unit to the wall using
tipping-restraint kit included.
the
CARE INSTRUCTIONS:
a
Dust often using a clean, soft, dry lint-free cloth.
a
Blot spills immediately, and wipe with clean, damp, cloth
a
We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
Thank you for your purchase
Stores l catalog l www.potterybarnkids.com
USA 1.800.290.8181
Page 5/5
Loading...