1
pottery barn kids
BOOKRACK TALL
PRE-ASSEMBLY:
Remove all parts and hardware from box and lay out on a carpeted or scratch
-
free work surface (The
shipping box provides and ideal work surface)
, as t
his will avoid damaging any parts during assembly.
Do not di
spose of any contents until assembly is completed to avoid accidentally discarding small parts
or hardware.
Two people
are
recommended for ease of assembly.
Use the parts and hardware lists to identify and separate each of the pieces included prior to star
ting
assembly.
The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
Note:Do
not fully tighten all bolts until all parts are in place. Failure to follow these instructions may
cause the bolts to misa
lign during assembly.
If using power tools to aid in assembly please use caution. Power tools can damage hardware of split
wood.
PARTS INCLUDED:
A–Bookrack Base
(x1)B–
Left side panel
(
x1)C–
Right
side panel (x1)
D–Frontrail (x4
)E–
Shelf with holes
(x1)F–Shelf w/o holes (x2
)
TOOLS
REQUIRED
:
Phillips head screwdriver (not included)
G–Ball Tip
Allen Key
(included)
HARDWARE:
H–Al
len
bolt
1/4”x45
x15
mm (x6)
I–Allen
bolt 1/4
”
x32
x15
mm (x4)
2
J–Metal washer
1/4"x24x12x8mm
(x6)K–
Drywall Anchors
5/32”x
63x14mm(x2)L–Screw
5/32”x53mm(
x2)M–
Phillips head
wood
screw 8x38
mm (x2)
N–Paper template (x1)
ASSEMBLY:
1.
Laythe
Right
side panel (
C)
down as shown
in the illustration below
.
Attach
the
Shelf with holes (E)
and
Shelf w/o holes (F) to the
Right
side panel (
C)
using 3pcs Allen bolt 1/4
”
x45x15mm (H)
and
3pcs
Metal
washer
1
/4"x24x12x8mm
(J)
, tighten with
Allen key (G).
Make
sure
Shelf with holes (E)
at
the upper.
3
2.
Fit 4pcs Front rail (D) to th
e Right
side panel (
C)
firmly
as shown.
3.
Attach the Left
side panel (B) to the
Shelf with holes (E) and S
helf w/o holes (F) using 3pcs Allen
bolt 1/4
”
x45x15mm (H) and 3pcs Metal washer
1/4"x24x12x8mm
(J) , tighten with Allen key
(G)
.
4
4. Attach the
Bookrack Base (A) to the Left side panel (
B) and Right si
de panel (C ) using 4pcs
Allen bolt
1/4”x32x15mm (I) as shown.
A
ssembly completed.
5.
Place
the paper template (
N)at the desired loation on wall
and ensure that the template is level.
Using a pecil , mark the locations on the
wall as shown. This is where the hardware will be inserted.
56.Fordrywall
mounting
: using
a Phillip
’
s head
screwdriver,
insert the drywall anchors (K) into the wall at the
insertion
points.
Press and turn clockwise until anchors are flush wi
th the wall.
7.Align
the holes
i
n the
bookrack
with
the
anchors. Then i
nsert
each
screw (L) into the anchors
at the insertion
points,
leaving approximately 1/2
”
between the back
of the screw head and the wall.
Attach the rack to the wall
.68
.
For
stud
mounting
:using2each
Phillips
head
wood
screws8x38
mm (M
), insert each wood screw thru the
appropriate holes in the wooden rack. Align them with the wall stud or pencil marks and attach the rack to the
wall.
T
hank you for your purchase
stores | catalog |
www.potterybarnkids.com
Loading...