Pottery Barn Madison Small Hutch Assembly Instruction

pottery barn kids

MADISON CABINET HUTCH

IMPORTANT SAFETY INSTRUCTIONS:

• Please read all instructions carefully before assembling.

• For your safety, assembly by two adults is recommended.

PRE-ASSEMBLY:

• Remove all parts and hardware from the box and lay out on a clean, carpeted, or scratch-free work surface,
as this will avoid damaging any parts during assembly. The shipping box provides an ideal work surface. Do
not dispose of any contents until assembly is completed to avoid accidentally discarding small parts or
hardware.

• Use the parts and hardware lists above to identify and separate each of the pieces included.

• The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.

• Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause

the bolts to misalign during assembly. Minifix Cam
reach this angle, please unscrew t he Minifix Connecting Bolt a lit tl e an d t ry a g ai n .

• If using power tools to aid in assembly please use caution. Power tools can damage hardware or split
wood.

• This product has two version of door placement, the first version is to open from right, and the second is
from left. The door in the hutch package is for the first version (open door from right). If you want the
second version (open door from left), you need the door of another product – the Madison Cabinet - and
skip the following step 7 and refer to step 8,9,10.

PARTS INCLUDED:

(A) Left Side Panel – 1pc
(B) Right Side Panel – 1pc
(C) Low Shelf– 1pc
(D) Upper shelf– 1pc
(E) Top Panel– 1pc
(F) Back Panel – 1pc
(G) Rail– 1pc
(H) Door– 1pc

TOOLS REQUIRED:
Phillips Head Screwdriver (not included)

need to be screw over 90° at least. If you feel hard to

HARDWARE ENCLOSED:

(I) Minifix Connecting Bolt – 10pcs (J) Minifix Cam – 10pcs

(K) Wooden Dowel – 10pcs

(M) Shelf Pin – 4pcs

(O) Screw for Hinge – 8pcs

(P) Magnet –1pc

(R) Metal Piece --1pc

(T) Knob - 2pcs

V) Connecting Piece --2pcs (W) Screw for Connecting Piece --4pcs

(X) Mounting Bracket --2pcs

(Z1) Long screw for wall Bracket --2pcs

(Z3) Sleeve screw --2pcs

NOTE: One extra knob and knob screw are included for your convenience.

2

( Assembled on top) (Q)Screw for Magnet -2pcs (Assembled on top)

(U)Screw for Knob – 2pcs

(L)Screw for Back Panel – 16pcs

(N) Hinge– 2pcs (Assembled on door)

(4pcs Assembled on door)

( Assembled on door) (S) Screw for Metal piece -1pc ( Assembled on door)

(Y) Short screw for product Bracket --2pcs

(Z2) Plastic strip

(Z4) Sleeve nut – 2pcs

ASSEMBLY INSTRUCTIONS:

1. Assembl e th e Lo w e r s he l f (C) t o Left Side Panel (A). In se r t Wooden Dowels (K) and screw Minifix
Connecting Bolts (I) into the pre-drilled holes in the middle of Left Side Panel (A), as shown i n F i g. 1 . Th e n,
align the pre-drilled holes of the Lower Shelf (C) with the assembled Wooden Dowels (K) and Minifix
Connecting Bolts (I) of the Left Side Panel (A). (see Fig1). Insert Minifix Cam (J) into the pre-drilled holes
on the bottom surface of the Lower Shelf (C). Lock Minifix Cam (J) in place by turning 180° with a Phillips
Head Screw driver (not included), Fig 1.

2. Assemb l e t h e R a i l ( G ) t o th e L e f t Side Panel (A). In s er t a Wooden Dowels (K) and screw Minifix
Connecting Bolt (I) into the pre-drilled holes near the bottom side of Left Side Panel (A), as shown i n F i g. 1.
Then, align the pre-drilled holes of the Rail (G) with the assembled Wooden Dowel (K) and Minifix
Connecting Bolt (I) of the Left Side Panel (A). See Fig. 1. Then insert (1) Minifix Cam (J) into the pre-d rilled
hole on the back surface of Rail (G), close to the end. Lock Minifix Cam (J) in place by turning with Phillips
Head Screwdriver (not included) Fig 1

Rail (G)

Lower Shelf (C)

Left Side Panel (A )

(Fig. 1)

3. Insert Wooden Dowels (K) and screw Minifix Connecting Bolt (I) into t h e p re - d ri l l ed h o l es in t he m i dd l e o f
the Righ t Side Panel (B), as w e l l a s i n t h e p r e- d rilled holes located at the bottom of the Right Side Panle (B),
as shown in Fig. 2. Then, align the pre-drilled holes of the Lower Shelf (C) and Rail (G) with the assembled
Wooden Dowels (K) and Minifix Connecting Bolts (I) of the Right Side Panel (B). See Fig. 2. Insert Minifix
Cam (J) into the pre-drilled holes on the sides of the Lower Shelf (C) and Rail (G). Lock Minifix Cam (J) in
place by turning with a Phillips Head Screwdriver (not included). (Fig. 2)

3