Page 1
pottery barn kids
KENDALL TOWER
PRE
-
ASSEMBLY:
Please read all instruction before beginning assembly.
The illustrations provided allow for easier assembly
when used in conjunction with the assembly instructions.
Remove all parts and hardware from box and l
ay out on a carpeted or scratch
-
free work
surface,
as t
his will
avoid damaging any parts during assembly. The shipping box provides and ideal work surface
.
Do not dispose
of any contents until assembly is completed to avoid accidentally discarding small pa
rts or hardware.
For your safety and
ease, adult assembly
by t
wo people is recommended.
Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or
hardware.
Use the parts and hardware lists to identify and sep
arate each of the pieces included prior to starting
assembly.
Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the
bolts to misalign during assembly.
If using power tools to aid in assembly p
lease use caution. Power tools can damage hardware or split wood.
PARTS INCLUDED:
(A)
Top-1pc(B)
Left panel
-1pc(C)Right panel
-1pc(D)Front rail
-1pc(E)Adjustable shelf
-3pcs(F)
Fixed shelf
-1pc(G)Back panel
-1pcTOOLS
REQUIR
ED:
Phillips head screwdriver (not included)
HARDWARE
ENCLOSED
:(H)1/4x1-1/4”
Bolts
-8pcs(I)1/4x1-1/2”
Bolts
-2pcs(K
) Washer 1/4mm
–
8pcs
(L) Spring washer 1/4mm
–
8pcs
(M)
#3x15
mm–26
pcs(N)Shelf support
–12pc
s
EBCDFGA
Page 2
(O)
Curve washer
–2pcs(P) 4mm Allen Key
–
1pc
ASSEMBLY
INSTRUCTIONS
:
1.
Position
the Side panel (B)
and the fixed shelf (F)
exactly as sho
wn
(Fig.4) Align the pre
-
drilled holes on the Side panel
(B) with the p
re-drilled holes
on the c
l
eat on the fixed shelf (F). Insert the Washer (K), Spring washer (L) and
1/4x1-1/4”
Bolt (H) through pre
-
drilled holes on the side panel (B) and the pre
-
drilled holes on the c
l
eat on the fixed shelf (F),
tighten with the Allen k
ey (P) provided
Position the Front rail (D) exactly as shown (Fig.
1). Slot the
1/4x 1
-
1/2”
Bolt (I) through
Front rail (D)
Curve washer
(O).Attach the Front rail (D) onto the side panel as shown in the diagram. Slot the 1/4 x 1
-
1/2”Bott (I) into the
postinthe side panel, tighten with the Allen key (P) provided.
(Fig. 1)
2
. Po
sition the Panel (C ) and the assembled frame (assembled in step 1) exactly as shown. (Fig.2) Align the pre
-
drilled holes on the Side panel (C ) with the pre
-
drilled holes on the assembled frame. Insert the
Insert the Washer (K),
Spring washer (L) and
1/4x1-
1/4”
Bolt (H) through pre
-
drilled holes
on the
post
on the side panel, tightening with the
Allen key (P) provided.
IOHLKDF
B
Page 3
(Fig. 2)
3
. Attach the Top (A) onto the
Side panels (B) and (C) by inserting the pre
-
atta
ched wooden dowels on the
top
horizontal rails
of the Side panel (B)
and (C) into the pre
-
drilled holes on the Top (A). Insert
Allen Bolts into the pre
-
drilled holes at both ends of the Top. Once all bolts are in place, fully tighten them using the 4mm
Allen Key
(P).
(Fig.3)4. Attach the Back Panel (G) to the back of the unit. Insert the Screws through pre
-
drilled holes of the Back panel (G)
into the unit. Secure with Philips Head Screwdriver.
IOHLKCAHL
K
Page 4
(Fig.4)5
. Insert the Shelf Support (N)
into the pre
-
drilled located on the interior of the
Tower as shown in Figure 5. Carefully
place the Adjustable Shelves (E) onto the shelf support as shown in Figure 5.
(Fig.5)
GME
N
Page 5
6.Adjust the Adjustable Levelers on the bottom of the Legs by loosening or tightening them so the T
ower
sits evenly
on floor.
(Fig.6)
CARE INSTRUCTIONS:
Dust often using a
clean, soft, dry lint
-
free cloth.
Blot spills immediately, and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered
finish.
T
hank you for your purchase
stores | catalog | www.potterybarnkids.com
Loading...