pottery barn kids
EMERY DESK HUTCH
PRE-ASSEMBLY:
• Please read all instruction before beginning assembly. The illustrations provided allow for easier
assembly when used in conjunction with the assembly instructions.
• Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surfa ce, as this
will avoid damaging any parts during assembly. Th e shipping box provide s and ideal work surface. Do
not dispose of any contents until assembly is completed to avoid accident ally discarding sm all p art s or
hardware.
• For your safety and ease, adult assembly by two people is recommended.
• Save all packing materials until assembly is complete to avoid accidentally discar ding smaller parts or
hardware.
• Use the parts and hardware lists to identify and sep arate each of the pieces included prior to starting
assembly.
• Note: DO not fully tighten all bolts until all parts are in place. Failure to follow these instructions may
cause the bolts to misalign during assembly.
• If using power tools to aid in assembly please use caution. Power tools can damage hardware of split
wood.
PARTS INCLUDED:
(A) Adjustable shelf – 2pcs (B) De
H
ARDWARE ENCLOSED:
(C) Shelf support – 8pcs
) Small Phillips head screws 7x15mm – 8pcs
(D
sk hutch with drawer – 1pc
) Metal plate 112x20mm – 2pcs
(E
(F
) Bracket 48x21x10mm – 2pcs
(G
) Long screw 6x32mm – 2pcs
(H
) Short screw 6x19mm – 2pcs
(I
) Nylon strap 300x12x8mm – 1pc
T
OOLS REQUIRED:
Phillips head screwdri
ver (not included)
A
SSEMBLY INSTRUCTIONS:
1. Determine the desired heig
ht for shelf inside the Desk hutch, and insert 4 Shelf supports (C) f or each shelf,
taking care to ensure they are all on the same level. Place each Shelf (A) on the Shelf support s.
2 esk hutch on the desk in upright position, taking
. Carefully place the d care not to scratch the surface of the
desktop, as shown.
3. Using a Philips head screwdriver (not included), place the Metal plates (E) over the pre-drilled holes on the
back edge of the desk hutch and pre-drilled holes of the desk and fasten the two pieces using the Small
Phillips head screw (D).
4. Hardware should be check
ed periodically for tightness.
ARE INSTRUCTIONS:
C
• Dust often using a
• Blot spills immediately, and wipe with a clean, da
clean, soft, dry lint-free cloth.
mp, cloth.
• We do not recommend the use of chemical cleansers, abras
finish.
Thank you for your purchase.
stores | ids.com
catalog | www.potterybarnk
USA 1.800.290.8181
ives, or furniture polish on our lacquered
F
URNITURE TIPPING RESTRAINT
Young children may be injured by tippin
g furniture. The use of a tipping restraint is highly recommended.
When properly installed, this restraint could provide protection against the un expected tipping of furniture du
small tremors, bumping or climbing. We recommend mounting this restraint to a wall stud.
ARNING: This product is only a deterrent. It is not a substitute for proper adult supervision.
W
Hardware Included (also described on page two):
(F) Brackets – 2pcs
(G) Long screws – 2p
cs
(H) Short screws – 2pcs
(I) Nylon strap – 1pc
STALLATION INSTRUCTIONS:
IN
1. Locate a wall stud behind
your furniture, Position a bracket (F) on the stud approximately 1” below the
top of the furniture. Mark and drill pilot hole into the center of the stud with a 3/32” drill bit. Att ach a
bracket (F) to the stud with the long screws (G) provided.
2. tached to the furniture frame at the top. To
On the back of the furniture, a bracket (F) will need to be at
do this, temporarily move the furniture into its final position and mark the location of the wall bracket
e to
on the furniture frame. Move the furniture away from the wall and place a bracket on the mark. Mark
and drill holes for screws with a 3/32” drill bit. Att ach the bracket to the furniture with the short screws
(H) provided.
Move the furniture into it
3. s final position, taking care to line up the wall bracket with the furniture bracket .
Thread strap (I) through the bracket as shown in the illustration. T ighten strap until snug. Do not over
tighten.
Loading...