pottery barn kids
EMERY 2 SHELF BOOKSHELF
PRE-ASSEMBLY:
• Please read all instruction before beginning assembly. The illustrations provided allow for easier
assembly when used in conjunction with the assembly instructions.
• Remove all parts and hardware from box and lay out on a carpeted or scratch-free work su rface, as this
will avoid damaging any parts during assembly. The shipping box provides and ideal work surface. Do
not dispose of any contents until assembly is completed to avoid accidentally discarding small parts or
hardware.
• For your safety and ease, adult assembly by two people is recommended.
• Save all packing materials until assembly is complete to avoid accidentally discar ding smaller parts or
hardware.
• Use the parts and hardware lists to identify and sep arate each of the pieces included prior to starting
assembly.
• Note: DO not fully tighten all bolts until all parts are in place. Failure to follow these instructions may
cause the bolts to misalign during assembly.
• If using power tools to aid in assembly please use caution. Power tools can damage hardware of split
wood.
PARTS INCLUDED:
(A) Top panel – 1pc
(B) Right side panel – 1pc
(C) Left side panel – 1pc
(D) Shelf – 1pc
(E) Bottom panel – 1pc
(F) Back panel – 1pc
TOOLS REQUIRED:
Phillips head screwdriver (not included)
HARDWARE:
(G) Allen bolt 1/4”x28x15mm – 12pcs
(H) Allen Key – 1pc
(I) Phillips head screws 8x32mm – 2pcs
(J) Phillips head screws 7 x 20mm – 6pcs
(K) Bracket 48x21x10mm – 2pcs
(L) Long screw 6x32mm – 2pcs
(M) Short screw 6x19mm – 2pcs
(N) Nylon strap 300x12x8mm – 1pc
ASSEMBLY INSTRUCTIONS:
1. Lay the Shelf (D) and Bottom panel (E) down as shown in the illustration below.
2. Attach the Right side panel (B), Left side panel (C) to Shelf (D) and Bottom panel (E) using Allen bolts (G)
and Allen key (H).
3. Fix th
4. Attach the Top panel (A) to the side panels as shown, using Short bolts (G) and Allen key (H).
e Bottom panel (E) to Side panel using Phillips head screws 8x32mm (I) as shown.
5 Insert and fasten the Phillips head screws 7 x 20mm (J) to Back panel (F) as shown.
.
ARE INSTRUCTIO
C NS:
• Dust often usi
• Blot spills im
• We do not re abrasives, or furniture polish on our lacquered
finish.
ng a clean, soft, dry lint-free cloth.
mediately, and wipe with a clean, damp, cloth.
commend the use of chemical cleansers,
Thank you for your purchase
stores | catalog | www.potterybarnkids.com
USA 1.800.290.8181
FURNITURE TIPPING RESTRAINT
Young children may be injured by tipping furniture. The use of a tipping restraint is highly recommended.
When properly installed, this restraint could provide protection agai nst the unexpected tipping of furniture due to
small tremors, bumping or climbing. We recommend mounting this restraint to a wall stud.
WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision.
Hardware Included (also described on page one):
(K) Brackets – 2pcs
(L) Long screws – 2pcs
(M) Short screws – 2pcs
(N) Nylon strap – 1pc
INSTALLATION INSTRUCTIONS:
1. Locate a wall stud behind your furniture, Position a bracket on the stud approximately 1” below the top
of the furniture. Mark and drill pilot hole into the center of the stud with a 3/32” drill bit. Attach a bracket
to the stud with the long screws provided.
2. On the back of the furniture, a bracket will need to be attached to the furniture frame at the top. To do
this, temporarily move the furniture into its final position and mark the location of the wall bracket on
the furniture frame. Move the furniture away from the wall and place a bracket on the mark. Mark and
drill holes for screws with a 3/32” drill bit. Attach the bracket to the furniture with the short screws
provided.
3. Move the furniture into its final position, taking care to line up the wall bracket with the furniture bracket.
Thread strap through the bracket as shown in the illustration. Tighten strap until snug. Do not over
tighten
Loading...