Installation Instructions
EVO-RD4-LCD15
document version 1.0
INTRODUCTION
Thank you for purchasing the EVO-RD4-LCD15. POS-X
strives to provide the best possible product and service
to its customers. If you experience any diculties with
this product, contact support at 800-790-8657 ext. 5.
SAFETY
To reduce the risk of personal injury and property
damage, adhere to the guidelines below.
WARNING!
Disconnect electrical devices from power when
performing physical maintenance, repair, or
modication to reduce the risk of electrical
shock and property damage.
Read all instructions before beginning
installation. If you are uncertain of your ability
to complete the installation, consult customer
support or other qualied personnel.
Follow all safety warnings for the EVO-TM4/EVOTP4 as described in its owner’s manual.
TOOLS REQUIRED
• Phillips Screwdriver #2
• USB Keyboard
• Kit for EVO-TM4 only (#EVO-RD4-LCD15TM)
IMPROVING THE POS EXPERIENCE
www.pos-x.com | 360.738.8433 | support@pos-x.com
INSTALLATION
Installation varies depending on which model you
will mount the rear display to. See the model-specic
instructions below and proceed as indicated.
EVO-TP4
Turn ON Powered VGA
via BIOS (Steps 1–5)
Install Display
(Steps 6–13)
Steps Required for Specic Models
To turn the powered VGA output ON (EVO-TP4 series
only, excluding EVO-TP4A-A):
Turn the system OFF. Note: If a USB keyboard is not
1
currently connected to the system, connect one now.
Turn the system ON while holding the Delete key to
2
enter the BIOS.
EVO-TP4A-A EVO-TM4
(Dual VGA Output Required)
Install Display
with VGA and Power Cord
from Kit # EVO-RD4-LCD8TM
(Steps 6–13)
Reboot System
INVENTORY
A. Mounting Bracket
B. VGA Cable
C. Screws (x2)
D. 15" Rear Display
B
Mounting bracket
Select the “Advanced” tab (A), then “Power
3
Conguration COM/VGA Ports” (B).
A
A
B
Conguring VGA Port
From the “Power Conguration COM/VGA Ports”
4
menu, select “VGA Power Setting” (A), then choose
“+12V” (B).
Set the unit upright, then line up the mounting pins
10
on the back of the rear display to the slots in the
bracket, as shown below.
A
B
C
Turning Power ON
Save and Exit from BIOS (C) by pressing F10, allow
5
the system to start, then turn it OFF.
To install the rear display (all models):
Make sure the system is OFF.
6
Disconnect the system from power.
7
Mounting Pins
Aligning mounting pins with slots.
Place the rear display onto the bracket, then secure
11
it by tightening the thumb screw shown below.
Bracket
Slots
Bracket
Turn the EVO-TP4/TM4 over to access the bottom of
8
the housing. Take care to place the unit on a clean,
non-abrasive surface to avoid damaging it.
Secure the mounting bracket to the EVO-TP4/TM4
9
base with the two included screws, as shown in the
gure below.
Mounting
Bracket
EVO-TP4/TM4
Base
Securing bracket to EVO-TP4/TM4 base.
Thumb Screw
Rear Display
Securing rear display to bracket.
If you are attaching the rear display to the EVO-
12
TP4, connect the supplied VGA cable from the rear
display VGA port to the powered VGA port on the
underside of the TP4.
If you are attaching the rear display to the EVO-
TM4, connect the supplied VGA cable from the
rear display VGA port to the 2nd VGA port on the
computer. Then, connect the power cord to the
“A/C In” port on the underside of the unit. Connect
the power cord to power. We recommend placing
the transformer in the TM4 base for a cleaner
installation.
Turn the unit and the rear display ON.
13
Loading...