LCD Racks Monitor
PRM-503A
MULTI-CHANNEL LCD MONITOR
User
s
Manual
,
Contents
Contents
PRM-503A
Warnings .......................................................................................................... 3
Features ............................................................................................................ 4
Name & Function of Each Part ......................................................................... 5
OSD Menu Organization & Adjustment ........................................................... 7
Other Functions .............................................................................................. 15
Special Functions ........................................................................................... 25
System Default Value...................................................................................... 26
Product Specification ..................................................................................... 27
2
PRM-503A MULTI-CHANNEL LCD MONITOR
3
Warning
Warning
· Always use set voltage.
- DC 12V
· If liquid is spilled on or impacts this product, please disconnect the product immediately
and seek professional help before continued use.
· Keep unit disconnected during extended periods of disuse.
·
·
Keep unit in a well-ventilated place to prevent overheating.
·
·
Do not install the product near any heat-generating equipment.
Also, keep the product out of direct sunlight or dusty areas.
·
·
Only clean the product with a noncommercial, mild and neutral detergent.
·
·
When transporting the product, make use of its original packaging for safer carriage.
FCC (Federal Communications Commission)
This equipment has been tested and found to comply with the limits for class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interface when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential to correct the interference at his own expense
Warning!! : Change or modifications not expressly approved by the manufacturer responsible for
compliance void the user’s authority to operate the equipment.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries
with separate collection systems)
This symbol on the product or on its packing indicates that this product shall not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequence for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. The recycling of materials will help to conserve natural
resources.
!
4
Features
Features
Multi-Format PRM-503A Series unit has the following features:
· Compatible with varied SDI Signals
The product is compatible with varied SDI signal
-480i,576i,720p,1035i,1080i,1080p,1080psf, 2K
· Compatible with varied Composite Signals
- NTSC, PAL, SECAM
· Waveform/Vector Scope/Audio Level Meter
Waveform & Vector Scope available for SDI Signals
Embedded Audio Level Meter
· BLUE ONLY/MONO
· H/V delay
· Wide Variety of Markers & Safety Areas
Center Marker, Safety Area Marker, Aspect Marker, Display Size(Scan)
· Pixel To Pixel
Provides both full screen and unscaled native image.
· Wide Screen/LED Backlight
· 24Bit RGB Interface Panel
· DC Compatible
The product is powered by normal 12V source.
· Remote control function
Simple remote controllability with single cable connection, no additional modules required
· Additional Features
Active Loop Through/SDI, 600:1 contrast ratio, 300 cd/m2 brightness, OSD user interface,
Rack Mountable
PRM-503A MULTI-CHANNEL LCD MONITOR
5
Name & Function of Each Part
Name & Function of Each Part
· [INPUT] button
Used to select SDI A / SDI B / COMPOSITE Input (Rotation)
· [MENU] button
Used to activate the OSD menu.
· [UP] button
Used to navigate menu during OSD menu activation. It may also be used to toggle
clockwise through 1:1 quadrants in native scan mode
· [DOWN] button
Used to navigate menu during OSD menu activation. It may also be used to toggle
counterclockwise through 1:1 quadrants in native scan mode
· [ENTER] button
Used to confirm a chosen value (or mode) within the OSD menu.
This can be used to control the position of Waveform in small size.
· [POWER] button
Power On/Off button.
If the signal is normal, LED lights in Green. If the signal is unsupported or disconnected,
LED lights in Yellow.
· TALLY
LED indicating monitor’s current status using optional Remote.
ENTER DOWN UP MENU INPUT
<FRONT>
TALLY
POWER
LED
6
Name & Function of Each Part
· REMOTE (RJ-45)
Connection for remote control of monitor.
· SDI A-IN (BNC)
SDI A signal input terminal
· SDI B-IN (BNC)
SDI B signal input terminal
· SDI-OUT (BNC)
SDI signal output terminal
· COMPISITE INPUT (BNC)
COMPOSITE signal input terminal
· COMPOSITE OUTPUT (BNC)
COMPOSITE signal output terminal
· FACTORY PGM (15 pins)
Input connector for FACTORY PGM allowing for firmware updates.
· DC IN (XLR, 4 pins)
Used to supply DC power; 12V
<REAR>
SDI OUTPUT
SDI B INPUT
SDI A INPUT
COMPOSITE OUTPUT
COMPOSITE INPUT
DC IN
REMOTE
FACTORY PGM
1
2
3
4
DC IN soket
1: GND
4: +12V
PRM-503A MULTI-CHANNEL LCD MONITOR
7
OSD Menu Organization & Adjustment
OSD Menu Organization & Adjustment
[1] MAIN - Picture
· Brightness
This Item controls the degree of brightness.
· Contrast
This item controls the contrast ratio.
· Chroma
This item controls saturation.
· Aperture
This item controls the picture sharpness.
· Phase
This item controls Phase value (Hue).
#This function is only available in Composite Input.
· NTSC Setup
This item sets IRE value in NTSC mode between 0 IRE and 7.5 IRE.
#This function is only available in Composite NTSC Input.
8
OSD Menu Organization & Adjustment
[2] MAIN - Color
· Color Temp
This item controls Color Temperature with presets of 3200K, 5600K, 6500K, 9300K and User1,
User2, User3 mode.
· User
On User Mode, the user may select and control R, G, & B GAIN, BIAS values by using the
[UP]/[DOWN]/[ENTER] buttons.
· Color Copy
In User Mode, user can copy the preset of 3200K, 5600K, 6500K or 9300K to make the custom
adjustment by using the Up/Down/Enter buttons.
[3] MAIN - Marker
· Marker
Used to show MARKER on the screen. The type of marker at work may be selected on the other
menu.
#This feature disables when the H/V Delay or Pixel to Pixel mode is activated.
PRM-503A MULTI-CHANNEL LCD MONITOR
9
OSD Menu Organization & Adjustment
· Line Marker
This selects the marker type when the Line Marker is displayed on the screen.
Compatible Line MARKER types are as follows:
· Center Marker
This item displays the Center Marker on the screen.
· Safety Area
This item controls the size of the Safety Area between 80%, 85%, 88%, 90%, 93% and 100%.
· Marker Mat
This item darkens the area outside of Line Marker setting area. The degree of the matte is
between OFF(0) and (7).
The higher the number the darker Line Marker the matte becomes.
· Marker Color
This item controls Marker color. Selectable colors are white, gray, black, red, green and blue.
# Line Marker, Center Marker and Safety Area functions are operates only after activating
the MARKER function by setting to ‘On’ the Marker menu.
[4] MAIN - Remote
REMOTE (RJ-45)
1: Pin1
2: Pin2
3: Pin3
4: Pin4
5: Pin5
6: Pin6
7: Pin7
8: GND
1 8
MODE Line Marker CLASS
HD
SD 16:9
16:9, 4:3, 4:3 ON AIR, 15:9, 14:9,
13:9, 1.85:1, 2.35:1, 1.85:1 & 4:3
SD 4:3
16:9
10
OSD Menu Organization & Adjustment
· Pin1 ~ Pin6
The user may connect RJ-45 jack to the remote terminal on the rear of the unit and designate a
function for each pin.
The selectable functions are as follows:
· Pin7
PIN7 is for POWER ON/OFF use only.
[5] MAIN - System [page1]
· System Default
User can use the System Default menu to initialize the values of the monitor.
· WaveForm
This item controls the Waveform or Vector Scope.
ANALOG CHANNEL, DIGITAL A CHANNEL, DIGITAL B CHANNEL
TALLY RED, TALLY GREEN
BLUE ONLY
UNDERSCAN
ASPECT
HVDELAY
16:9 MARKER, 15:9 MARKER, 14:9 MARKER,
13:9 MARKER, 4:3 MARKER, 4:3 ON AIR MARKER,
1.85:1 MARKER, 2.35:1 MARKER, 1.85:1 & 4:3 MARKER
CENTER MARKER
SAFETY AREA 80%, SAFETY AREA 85%, SAFETY AREA 88%,
SAFETY AREA 90%, SAFETY AREA 93%, SAFETY AREA 100%
PRM-503A MULTI-CHANNEL LCD MONITOR
11
OSD Menu Organization & Adjustment
· WaveForm Size
This item controls the size of Waveform or Vector Scope.
· WaveForm Position
This item controls the position of Waveform or Vector Scope between Right, Center and Left.
#In normal display, press Enter button to activate this feature.
#This feature can be activated in small size mode only.
· WaveForm Blending
This item activates the blending of Waveform or Vector Scope.
#This feature activates automatically if WaveForm overlaps with OSD.
#This feature can be activated in small size mode only.
· Audio Level Meter
This item set embedded audio group selects Off, G1+G2, G2+G3, G3+G4, G1+G3, G1+G4,
G2+G4 to activate Audio Level Meter.
#Menus or features which are related with WaveForm enables in SDI input mode only.
[6] MAIN - System [page2]
· Source ID
This item is used to activate the Source ID display by selecting BG Type or Char Type.
· Source ID Character
This item is used to customize the Source ID display. (A~Z, a~z, 0~9 and special characters)
12
OSD Menu Organization & Adjustment
· Source ID Position
This item controls the position of Source ID display. (Top-left, Top-center, Top-right, Bottom-right,
Bottom-center, Bottom-left)
· Source ID Color
This item is used to change the color of Source ID display by selecting black, white, red, green,
blue or yellow.
· Time Code
This item activates the Time Code. Select between VITC or LTC.
· Internal Pattern
This item is used to activate the internal Pattern of 100% White or 100% Color Bar.
[7] MAIN - System [page3]
· Back Light
This item controls the LED backlight setting. The value should be within range between
MIN(0) and MAX(25).
· Blue & Mono
You may remove R(red) and G(green) from the input signal and play the screen only with B(blue)
signal. Menu may be set to ‘Mono’ to change the screen to MONO mode.
(This mode uses only Luminance value.)
· Scan
This item controls to transfer from ZERO SCAN mode to Pixel To Pixel mode.
Mode changes in the order of Zero Scan -> Over Scan -> Pixel To Pixel -> Zero Scan.
#In Pixel to Pixel mode, Marker feature and menu disable automatically.
#In Pixel to Pixel mode, pressing Enter button rotates the position of display.
PRM-503A MULTI-CHANNEL LCD MONITOR
13
OSD Menu Organization & Adjustment
· Aspect Ratio
This item toggles aspect ratio in SD from standard to anamorphic.
#SD signal only (Disables automatically in any other signal including No signal)
· HV Delay
This item activates the HV Delay mode.
#In HV Delay mode, Marker feature and menu disable automatically.
· AFD
This item activates the AFD mode. Selectable mode are Off, Aspect Mode and Marker Mode.
#This feature action in only SDI signal included AFD Data.
#In Internal Pattern mode, this feature and menu disable automatically.
· Activating Internal Pattern disables Scan, Aspect Ratio and HV Delay.
[8] MAIN - System [page4]
· Set ID
This item controls the Set ID setting for UMD. The value should be within range between
0 and 99.
· Closed Caption
This item controls colsed caption ON/OFF. (708, 608(Line21), 608(ANC))
· Firmware Version
This item is the firmware version of the system.
· License
14
Other Functions
· PRM-503A Series unit is capable of process-
ing varied Input signals Composite and SDI.
· Press [INPUT] button on the front of the
monitor and activate the OSD menu as shown
on the left.
Select the input you desire by using the
[INPUT] Button.
· User can change and select the input mode
by using this one simple button.
# If no image displays after selecting the desired
input mode, check and make sure that your
connection is not lose or disconnected.
# Input resolution displays on the bottom of the
OSD screen.
[9] INPUT Menu
PRM-503A MULTI-CHANNEL LCD MONITOR
15
Other Functions
Other Functions
[1] PIXEL TO PIXEL
· PRM-503A monitor’s Pixel to Pixel mode displays input signal without scaling.
· To activate the [Pixel to Pixel] mode, access the Scan menu in Syetem menu and select
[Pixel to Pixel].
· In the [Pixel To Pixel] mode, use the [UP]/[DOWN] buttons to toggle between 1:1 scan
sections
Input Action Button Available Modes
HD 1080i/1080p
- OSD change
[UP]
(Clockwise)
[DOWN]
(Opposite)
Center -> Left Top ->Mid Top -> Right Top -> Right Mid -> Right
Bottom -> Mid Bottom -> Left Bottom -> Left Mid -> Center -> ….
Center -> Left Mid -> Left Bottom -> Mid Bottom -> Right Bottom
-> Right Mid -> Right Top -> Mid Top -> Left Top -> Center -> …
[UP]
[DOWN]
[UP]
[DOWN]
[UP]
[DOWN]
[UP]
[DOWN]
[UP] [DOWN]
[UP]
[DOWN]
[UP] [DOWN]
[UP] [DOWN]
[UP] [DOWN]
16
Other Functions
#Pixel To Pixel mode is not available in Graphic mode.
#Pixel To Pixel mode is available in SD mode, but 1:1 sections cannot be rotated through as
with HD sources.
Input Action Button Available Modes
HD 720p
- OSD change
[UP]
(Clockwise)
[DOWN]
(Opposite)
Center -> Left Top -> Right Top -> Right Bottom -> left Bottom ->
Center -> …
Center -> Left Bottom -> Right Bottom -> Right Top -> Left Top
-> Center -> ….
[UP]
[DOWN]
[UP]
[DOWN]
[UP]
[DOWN]
[UP] [DOWN]
[UP] [DOWN]
PRM-503A MULTI-CHANNEL LCD MONITOR
17
Other Functions
· Positions in HD Signal 1080i/1080p mode
· Position in HD Signal 720p mode
[UP]
[DOWN]
[UP]
[DOWN]
[UP]
[DOWN]
[UP] [DOWN][UP] [DOWN]
[UP]
[DOWN]
[UP]
[DOWN]
[UP]
[DOWN]
[UP]
[DOWN]
[UP] [DOWN]
[UP]
[DOWN]
[UP] [DOWN]
[UP] [DOWN]
[UP] [DOWN]
Center
Left Top Right Top
Right BottomLeft Bottom
Center
Left Top Mid Top
Right
To p
Right
Mid
Right
Bottom
Mid
Bottom
Left
Bottom
Left
Mid
18
Other Functions
[2] Waveform
· Waveform
· Waveform Size
If push the Input button (SDI-A ,SDI-B and Analog), Waveform full mode is change to
small mode automatically.
· Waveform Positions
OFF Waveform
Small (Y) Small (Cb, Cr, Y) Full (Y)
Left Center Right
Small display : YCbCr → Y → Cb → Cr → Vector → off
Full display : Y → Cb → Cr → Vector → off
OFF ON
· Waveform Blending
PRM-503A MULTI-CHANNEL LCD MONITOR
19
Other Functions
· Exception: If overlaps with OSD, blending activates automatically.
This function is only available with SDI Input.
Main OSD Info Window
Pixel To Pixel Source ID
Vector Scope OFF Vector Scope ON
[3] Vector Scope
·Vector Scope
Small Full
· Vector Scope Size
20
Other Functions
Vector Scope Position / Blending
: Refer to the Waveform position (P.18) and Waveform Blending (P.19)
This function is only available with SDI Input.
[4] Audio Level Meter
· Audio Level Meter
OFF HORIZONTAL VERTICAL
dBFS BBC EBU
VU Nordic
Peak hold Time
On signal, Blue bar
Permitted Max
Alignment
PRM-503A MULTI-CHANNEL LCD MONITOR
21
Other Functions
Group / Channel (Horizontal)
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
Group 1
Group 1
Group 2
Group 2
Group 3
Group 4
Group 4
Group 1
Group 1
Group 2
Group 2
Group 3
Group 4
Group 4
CH1 CH3 CH1 CH3 CH1 CH3 CH1 CH3 CH4 CH2CH4 CH2CH4 CH2CH4 CH2
Group / Channel (Vertical)
· Group & Channel
#This function is only available with SDI Input.
Audio Level Meter OFF Audio Level Meter ON
· Avoid Overlap
In full size WaveForm mode, WaveForm shifts down to avoid the overlap with Audio Level Meter.
22
Other Functions
[5] Time Code
#This function is only available with SDI Input.
Time Code + Audio Level Meter
Time Code + WaveForm Full Size Time Code + SourceID + WaveForm + Audio Level Meter
Time Code
BG Type Char Type
[6] Source ID
· Source ID
PRM-503A MULTI-CHANNEL LCD MONITOR
23
Other Functions
· Source ID Position
· Source ID Color
Left Top Mid Top Right Top
Left Bottom Mid Bottom Right Bottom
Black White Red Green Blue Yellow
[7] MAIN - System [page3]
· Back Light
This item controls the LED backlight setting. The value should be within range between
MIN(0) and MAX(50).
· AFD
This item activates the AFD mode. Selectable mode are Off, Aspect Mode and Marker mode.
This feature action in only SDI signal included AFD Data.
In Internal Pattern mode, this feature and menu disable automatically.
· Set ID
This item controls the Set ID setting for UMD. The value should be within range between 0 and 99.
· Closed Caption
This item controls closed caption ON/OFF.(708, 608(Line21), 608(ANC))
· Firmware Version
This item is the firmware version of the system.
· License
24
Other Functions
Special Functions
[1] HD Signal Activate (SD Version only)
This function activate SD/HD mode for SD only version.
You have to enter DOWN key for 5 seconds or more than in normal condition such as
without any window,
Display Description
· Default Window
- MENU : Close Window
- ENTER : Move to Window for Enter Code
· Enter Code Window
(Enter 8 codes in order left to right.)
- MENU : Close Window
- ENTER : Move Cursor to Right
- UP/DOWN : Change Code (0,2,3,5~7, A~Z)
· Enter Code Window
(Go submit after enter the code.)
- MENU : Close Window
- ENTER : Submit
·
Result Window
(Display a activate result.)
-
MENU : Close Window & System reboot
-
If you don’t enter any key, System will reboot
later 3 seconds automatically.
·
You can see the activate result on Default window
go back. (Success or None)
PRM-503A MULTI-CHANNEL LCD MONITOR
25
Special Functions
System Default Value
MEMU Value
Picture
Color
Marker
Remote
System [Page1]
System [Page2]
System [Page3]
System [Page4]
Brightness
Contrast
Chroma
Aperture
Phase
NTSC Setup
Color Temp
Gain Red (1/2/3)
Gain Green (1/2/3)
Gain Blue (1/2/3)
Bias Red (1/2/3)
Bias Green (1/2/3)
Bias Blue (1/2/3)
Color Copy
Marker
Line Marker
Center Marker
Safety Area
Maker Mat
Marker Color
PIN 1
PIN 2
PIN 3
PIN 4
PIN 5
PIN 6
System Default
WaveForm
WaveForm Size
WaveForm Position
WaveForm Blending
Audio Level Meter
Source ID
Source ID Character
Source ID Position
Source ID Color
Time Code
Internal Pattern
Back Light
Blue & Mono
Scan
Aspect Ratio
HV Delay
AFD
Set ID
Closed Caption
0
0
0
0
0
7.5 IRE
6500K
0
0
0
0
0
0
6500K
Off
Off
Off
Off
Off
White
Analog Channel
Digital A Channel
Digital B Channel
Tally R
Tally G
Blue Only
No
Off
Small
Right Bot
Off
Off
Off
C A M – 1
Left Top
Black
Off
Off
20
Off
Zero Scan
16:9
Off
Off
0
Off
26
Product Specification
Product Specification
* Above specications may be changed without notice
Input (1 Screen)
Output (1 Screen)
Input Signal
SDI Input Signal Formats
LCD
Power
Power Consumption (Approx.)
Operating Temperature
Storage Temperature
Main Body Dimensions (mm/inch)
Weight
Accessory
Option
1 x BNC
2 x BNC
1 x BNC
1 x BNC
Analog
HD-SDI
SD-SDI
SMPTE-274
SMPTE-296M
SMPTE-260M
SMPTE-125M
ITU-R.BT.656
2K Format
Size
Resolution
Pixel Pitch
Color
Viewing Angle
Luminance of White
Contrast
Display Area
Composite Input
SDI Input
Composite Output (Internal Buer Output)
SDI Output (Active Through Out)
Composite (1.0Vpp with Sync)
1.485 Gbps
270 Mbps
1080i (60/59.94/50)
1080P (30/29.97/25/24/24sF/23.98/23.98sF)
720P (23.98/24/25/29.97/30/50/59.94/60)
1035i (60/59.94)
480i (59.94)
576i (50)
2048 x 1080 (23.98psf/24psf/23.98p/24p)
5.0 inch
800 x 480 (15 : 9)
0.135(H) x 0.135(V) mm
16.7M (True), 24bit
H : 170 degrees
V : 170 degrees
300cd/m² (center)
600 : 1
108.0 x 64.8 mm
12V DC
Watts
0℃ to 40℃ (32℉ to 104℉)
-30℃ to 50℃ (-22℉ to 122℉)
2.5kg(5.5 lbs)
DC Power Adapter
19” Rack Mountable Kit (2U) (Triple Monitor)
480 x 87 x 68mm / 18.89 x 3.42 x 2.67 inch
PRM-503A MULTI-CHANNEL LCD MONITOR
27
Product Specification
POSTIUM KOREA
Co., Ltd.
208, Building A, Samsong Techno Valley, 140, Tongil-ro,
Deogyang-gu, Goyang-si, Gyeonggi-do, Korea, 10594
Tel : +82.2.354.6055 / Fax : +82.2.354.6056
E-mail : sales@posum.com / www.posum.com
Loading...