Post-it(R) Flag Highlighter and Pen (3-in-1) 02/10/15
________________________________________________________________________________________________________
Page 1 of 1
Safety Data Sheet
Copyright,2015,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed
provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither
the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
Document Group:
25-5098-6
Version Number:
2.00
Issue Date:
02/10/15
Supercedes Date:
04/28/10
Product identifier
Post-it(R) Flag Highlighter and Pen (3-in-1)
Recommended use
Office Supply
Supplier's details
MANUFACTURER:
3M
DIVISION:
Stationery and Office Supplies Division
ADDRESS:
3M Center, St. Paul, MN 55144-1000, USA
Telephone:
1-888-3M HELPS (1-888-364-3577)
Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
This product is a kit or a multipart product which consists of multiple, independently packaged components. A Safety Data
Sheet (SDS), Article Information Sheet (AIS), or Article Information Letter (AIL) for each of these components is included.
Please do not separate the component documents from this cover page. The document numbers for components of this
product are:
18-8795-9, 19-0899-5
DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES NO
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the SDS available directly from 3M
3M USA SDSs are available at www.3M.com
Post-it(R) Flag+ Ball Point Pen Ink 04/03/14
__________________________________________________________________________________________
Page 1 of 5
Article Information Sheet
Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
This Article Information Sheet is provided as a courtesy in response to a customer request. A Safety Data Sheet (SDS) has not
been prepared for these product(s) because they are articles. Articles are not subject to the Occupational Safety and Health
Administration’s Hazard Communication Standard (29 CFR 1910.1200(b)(6)(v)). As defined in this standard: “Article”
means a manufactured item other than a fluid or particle: (i) which is formed to a specific shape or design during
manufacture; (ii) which has end use function(s) dependent in whole or in part upon its shape or design during end use; and
(iii) which under normal conditions of use does not release more than very small quantities, e.g., minute or trace amounts of a
hazardous chemical, and does not pose a physical or health risk to employees.
Document Group:
18-8795-9
Version Number:
1.00
Issue Date:
04/03/14
Supercedes Date:
Initial Issue
SECTION 1: Identification
1.1. Product identifier
Post-it(R) Flag+ Ball Point Pen Ink
1.2. Recommended use and restrictions on use
Recommended use
Ink for use in a ball point pen.
1.3. Supplier’s details
MANUFACTURER:
3M
DIVISION:
Stationery and Office Supplies Division
ADDRESS:
3M Center, St. Paul, MN 55144-1000, USA
Telephone:
1-888-3M HELPS (1-888-364-3577)
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
This product is exempt from hazard classification according to OSHA Hazard Comunication Standard, 29 CFR 1910.1200.
SECTION 3: Composition/information on ingredients
Ingredient C.A.S. No. % by Wt
2-PHENOXYETHANOL 122-99-6 45 - 55
INERT INGREDIENTS Trade Secret* 20 - 40
BENZYL ALCOHOL 100-51-6 5 - 20
PIGMENTS Trade Secret* 4 - 15
Post-it(R) Flag+ Ball Point Pen Ink 04/03/14
__________________________________________________________________________________________
Page 2 of 5
*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
No need for first aid is anticipated.
Skin Contact:
No need for first aid is anticipated.
Eye Contact:
No need for first aid is anticipated.
If Swallowed:
No need for first aid is anticipated.
SECTION 5: Fire-fighting measures
In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Not applicable.
6.2. Environmental precautions
Not applicable.
6.3. Methods and material for containment and cleaning up
Not applicable.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
This product is considered to be an article which does not release or otherwise result in exposure to a hazardous chemical
under normal use conditions.
7.2. Conditions for safe storage including any incompatibilities
No special storage requirements.
SECTION 8: Exposure controls/personal protection
This product is considered to be an article which does not release or otherwise result in exposure to a hazardous chemical
under normal use conditions. No engineering controls or personal protective equipment (PPE) are necessary.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
General Physical Form:
Liquid
Post-it(R) Flag+ Ball Point Pen Ink 04/03/14
__________________________________________________________________________________________
Page 3 of 5
Odor, Color, Grade:
Viscous ink with slight odor
Odor threshold
No Data Available
pH
6 - 8
Melting point
Not Applicable
Boiling Point
No Data Available
Flash Point
>= 100 ºC [Test Method: Closed Cup]
Evaporation rate
No Data Available
Flammability (solid, gas)
Not Applicable
Flammable Limits(LEL)
No Data Available
Flammable Limits(UEL)
No Data Available
Vapor Pressure
No Data Available
Vapor Density
No Data Available
Density
No Data Available
Specific Gravity
1.11 [Ref Std: WATER=1]
Solubility in Water
Moderate
Solubility- non-water
No Data Available
Partition coefficient: n-octanol/ water
No Data Available
Autoignition temperature
No Data Available
Decomposition temperature
No Data Available
Viscosity
> 1,000
SECTION 10: Stability and reactivity
This material is considered to be non reactive under normal use conditions.
SECTION 11: Toxicological information
Inhalation:
No health effects are expected
Skin Contact:
No health effects are expected
Eye Contact:
No health effects are expected
Ingestion:
No health effects are expected
Additional Information:
This product, when used under reasonable conditions and in accordance with the directions for use, should not present a
health hazard. However, use or processing of the product in a manner not in accordance with the product's directions for use
may affect the performance of the product and may present potential health and safety hazards.
SECTION 12: Ecological information
This article is expected to present a low environmental risk either because use and disposal are unlikely to result in a
Post-it(R) Flag+ Ball Point Pen Ink 04/03/14
__________________________________________________________________________________________
Page 4 of 5
significant release of components to the environment or because those components that may be released are expected to have
insignificant environmental impact.
SECTION 13: Disposal considerations
Dispose of contents/container in accordance with the local/regional/national/international regulations.
SECTION 14: Transport Information
For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.
SECTION 15: Regulatory information
Chemical Inventories
This product is an article as defined by TSCA regulations, and is exempt from TSCA Inventory requirements.
SECTION 16: Other information
NFPA Hazard Classification
Health: 0 Flammability: 1 Instability: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
HMIS Hazard Classification
Health: 0 Flammability: 1 Physical Hazard: 0 Personal Protection: X - See PPE section.
Hazardous Material Identification System (HMIS® III) hazard ratings are designed to inform employees of chemical hazards
in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use
and are not intended for use in emergency situations. HMIS® III ratings are to be used with a fully implemented HMIS® III
program. HMIS® is a registered mark of the American Coatings Association (ACA).
Document Group:
18-8795-9
Version Number:
1.00
Issue Date:
04/03/14
Supercedes Date:
Initial Issue
DISCLAIMER: The information in this Article Information Sheet (AIS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a
particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and
application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user
evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or
application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer
may have resulted in errors, omissions or alterations in this information,3M makes no representations as to its completeness
or accuracy. In addition, information obtained from a database may not be as current as the information in the AIS available
directly from 3M.
Post-it(R) Flag+ Ball Point Pen Ink 04/03/14
__________________________________________________________________________________________
Page 5 of 5
3M USA AISs are available at www.3M.com
Post-it(R) Flag+ Highlighter Fluid - All Colors 05/09/14
__________________________________________________________________________________________
Page 1 of 9
Safety Data Sheet
Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
This Safety Data Sheet (SDS) is provided as a courtesy in response to a customer request. This product is not regulated
under, and a SDS is not required for this product by the OSHA Hazard Communication Standard (29 CFR 1910.1200)
because, when used as recommended or under ordinary conditions, it should not present a health and safety hazard. However,
use or processing of the product not in accordance with the product's recommendations or not under ordinary conditions may
affect the performance of the product and may present potential health and safety hazards.
Document Group:
19-0899-5
Version Number:
7.01
Issue Date:
05/09/14
Supercedes Date:
08/24/10
SECTION 1: Identification
1.1. Product identifier
Post-it(R) Flag+ Highlighter Fluid - All Colors
1.2. Recommended use and restrictions on use
Recommended use
Ink for use in a highlighter.
1.3. Supplier’s details
MANUFACTURER:
3M
DIVISION:
Stationery and Office Supplies Division
ADDRESS:
3M Center, St. Paul, MN 55144-1000, USA
Telephone:
1-888-3M HELPS (1-888-364-3577)
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
2.1. Hazard classification
This product is exempt from hazard classification according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.
2.2. Label elements
Signal word
Not applicable.
Symbols
Not applicable.
Pictograms
Not applicable.
Post-it(R) Flag+ Highlighter Fluid - All Colors 05/09/14
__________________________________________________________________________________________
Page 2 of 9
Precautionary Statements
Storage:
Keep container tightly closed.
2.3. Hazards not otherwise classified
None.
3% of the mixture consists of ingredients of unknown acute oral toxicity.
SECTION 3: Composition/information on ingredients
Ingredient C.A.S. No. % by Wt
ETHYLENE GLYCOL 107-21-1 10 - 30
PIGMENT Trade Secret* 0 - 1
WATER 7732-18-5 70 - 90
*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
No need for first aid is anticipated.
Skin Contact:
No need for first aid is anticipated.
Eye Contact:
No need for first aid is anticipated.
If Swallowed:
No need for first aid is anticipated.
4.2. Most important symptoms and effects, both acute and delayed
See Section 11.1. Information on toxicological effects.
4.3. Indication of any immediate medical attention and special treatment required
Not applicable
SECTION 5: Fire-fighting measures
5.1. Suitable extinguishing media
Non-combustible. Use a fire fighting agent suitable for surrounding fire.
5.2. Special hazards arising from the substance or mixture
None inherent in this product.
Hazardous Decomposition or By-Products
Substance Condition
Carbon monoxide During Combustion
Post-it(R) Flag+ Highlighter Fluid - All Colors 05/09/14
__________________________________________________________________________________________
Page 3 of 9
Carbon dioxide During Combustion
5.3. Special protective actions for fire-fighters
No unusual fire or explosion hazards are anticipated.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Not applicable.
6.2. Environmental precautions
Not applicable.
6.3. Methods and material for containment and cleaning up
Not applicable.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
This product is considered to be an article which does not release or otherwise result in exposure to a hazardous chemical
under normal use conditions. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.)
7.2. Conditions for safe storage including any incompatibilities
Store away from oxidizing agents.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Occupational exposure limits
Ingredient C.A.S. No. Agency Limit type Additional Comments
ETHYLENE GLYCOL 107-21-1 Amer Conf of
Gov. Indust.
Hyg.
CEIL(as aerosol):100 mg/m3
ETHYLENE GLYCOL 107-21-1 Chemical
Manufacturer
Rec Guid
CEIL(as vapor and
aerosol):100 mg/m3
Amer Conf of Gov. Indust. Hyg. : American Conference of Governmental Industrial Hygienists
American Indust. Hygiene Assoc : American Industrial Hygiene Association
Chemical Manufacturer Rec Guid : Chemical Manufacturer's Recommended Guidelines
US Dept of Labor - OSHA : United States Department of Labor - Occupational Safety and Health Administration
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling
8.2. Exposure controls
8.2.1. Engineering controls
Not applicable.
8.2.2. Personal protective equipment (PPE)
Eye/face protection
Post-it(R) Flag+ Highlighter Fluid - All Colors 05/09/14
__________________________________________________________________________________________
Page 4 of 9
Under normal use conditions, eye exposure is not expected to be significant enough to require eye protection.
Skin/hand protection
Under normal use conditions, skin exposure is not expected to be significant enough to require skin protection.
Respiratory protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
General Physical Form:
Solid
Specific Physical Form:
Non-Woven Material
Odor, Color, Grade:
Felt tube filled with yellow highlighter fluid.
Odor threshold
No Data Available
pH
No Data Available
Melting point
Not Applicable
Boiling Point
210 ºF [Details: (liquid in felt tube)]
Flash Point
Not Applicable
Evaporation rate
No Data Available
Flammability (solid, gas)
Not Classified
Flammable Limits(LEL)
Not Applicable
Flammable Limits(UEL)
Not Applicable
Vapor Pressure
18 mmHg [@ 68 ºF]
Vapor Density
No Data Available
Density
1.08 - 1.1 g/ml
Specific Gravity
1.08 - 1.1 [Ref Std: WATER=1]
Solubility in Water
Negligible
Solubility- non-water
No Data Available
Partition coefficient: n-octanol/ water
No Data Available
Autoignition temperature
Not Applicable
Decomposition temperature
No Data Available
Viscosity
No Data Available
SECTION 10: Stability and reactivity
10.1. Reactivity
This material may be reactive with certain agents under certain conditions - see the remaining headings in this section.
10.2. Chemical stability
Stable.
10.3. Possibility of hazardous reactions
Hazardous polymerization will not occur.
10.4. Conditions to avoid
Post-it(R) Flag+ Highlighter Fluid - All Colors 05/09/14
__________________________________________________________________________________________
Page 5 of 9
None known.
10.5. Incompatible materials
Strong oxidizing agents
10.6. Hazardous decomposition products
Substance Condition
None known.
Refer to section 5.2 for hazardous decomposition products during combustion.
Under recommended usage conditions, hazardous decomposition products are not expected. Hazardous decomposition
products may occur as a result of oxidation, heating, or reaction with another material.
SECTION 11: Toxicological information
The information below may not be consistent with the material classification in Section 2 if specific ingredient
classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be
reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be
present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be
relevant to the material as a whole.
11.1. Information on Toxicological effects
Signs and Symptoms of Exposure
Based on test data and/or information on the components, this material may produce the following health effects:
Inhalation:
No health effects are expected.
Skin Contact:
No health effects are expected.
Eye Contact:
No health effects are expected.
Ingestion:
No health effects are expected.
Toxicological Data
If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or
the data are not sufficient for classification.
Acute Toxicity
Name Route Species Value
Overall product Ingestion No data available; calculated ATE > 5,000 mg/kg
ETHYLENE GLYCOL Ingestion Human LD50 1,600 mg/kg
ETHYLENE GLYCOL Inhalation-
Dust/Mist
(4 hours)
Other LC50 estimated to be 5 - 12.5 mg/l
ETHYLENE GLYCOL Dermal Rabbit 9,530 mg/kg
ATE = acute toxicity estimate
Skin Corrosion/Irritation
Post-it(R) Flag+ Highlighter Fluid - All Colors 05/09/14
__________________________________________________________________________________________
Page 6 of 9
Name Species Value
ETHYLENE GLYCOL Rabbit Minimal irritation
Serious Eye Damage/Irritation
Name Species Value
ETHYLENE GLYCOL Rabbit Mild irritant
Skin Sensitization
Name Species Value
ETHYLENE GLYCOL Human Some positive data exist, but the data are not
sufficient for classification
Respiratory Sensitization
Name Species Value
Germ Cell Mutagenicity
Name Route Value
ETHYLENE GLYCOL In Vitro Not mutagenic
ETHYLENE GLYCOL In vivo Not mutagenic
Carcinogenicity
Name Route Species Value
ETHYLENE GLYCOL Ingestion Multiple
animal
species
Not carcinogenic
Reproductive Toxicity
Reproductive and/or Developmental Effects
Name Route Value Species Test Result Exposure
Duration
ETHYLENE GLYCOL Ingestion Not toxic to female reproduction Multiple
animal
species
NOAEL
1,000
mg/kg/day
2 years
ETHYLENE GLYCOL Ingestion Not toxic to male reproduction Multiple
animal
species
NOAEL
1,000
mg/kg/day
2 years
ETHYLENE GLYCOL Dermal Some positive developmental data exist,
but the data are not sufficient for
classification
Mouse NOAEL
3,549
mg/kg/day
during
organogenesi
s
ETHYLENE GLYCOL Ingestion Some positive developmental data exist,
but the data are not sufficient for
classification
Mouse LOAEL 750
mg/kg/day
during
organogenesi
s
ETHYLENE GLYCOL Inhalation Some positive developmental data exist,
but the data are not sufficient for
classification
Mouse NOAEL
1,000
mg/kg/day
during
organogenesi
s
Target Organ(s)
Specific Target Organ Toxicity - single exposure
Name Route Target Organ(s) Value Species Test Result Exposure
Duration
ETHYLENE GLYCOL Ingestion heart | nervous
system | kidney
and/or bladder |
respiratory system
Causes damage to organs Human NOAEL Not
available
poisoning
and/or abuse
ETHYLENE GLYCOL Ingestion central nervous
system depression
May cause drowsiness or
dizziness
Human NOAEL Not
available
poisoning
and/or abuse
ETHYLENE GLYCOL Ingestion liver Some positive data exist, but the
data are not sufficient for
classification
Human NOAEL Not
available
poisoning
and/or abuse
Post-it(R) Flag+ Highlighter Fluid - All Colors 05/09/14
__________________________________________________________________________________________
Page 7 of 9
Specific Target Organ Toxicity - repeated exposure
Name Route Target Organ(s) Value Species Test Result Exposure
Duration
ETHYLENE GLYCOL Ingestion kidney and/or
bladder | vascular
system
Some positive data exist, but the
data are not sufficient for
classification
Rat NOAEL 200
mg/kg/day
2 years
ETHYLENE GLYCOL Ingestion heart |
hematopoietic
system | liver |
immune system |
muscles
Some positive data exist, but the
data are not sufficient for
classification
Rat NOAEL
1,000
mg/kg/day
2 years
ETHYLENE GLYCOL Ingestion respiratory system Some positive data exist, but the
data are not sufficient for
classification
Mouse NOAEL
12,000
mg/kg/day
2 years
ETHYLENE GLYCOL Ingestion skin | endocrine
system | bone, teeth,
nails, and/or hair |
nervous system |
eyes
All data are negative Multiple
animal
species
NOAEL
1,000
mg/kg/day
2 years
Aspiration Hazard
Name Value
Please contact the address or phone number listed on the first page of the SDS for additional toxicological information
on this material and/or its components.
SECTION 12: Ecological information
Ecotoxicological information
Test Organism Test Type Result
, NA % weight
Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material
and/or its components.
Chemical fate information
Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material
and/or its components.
SECTION 13: Disposal considerations
13.1. Disposal methods
Dispose of contents/ container in accordance with the local/regional/national/international regulations.
Prior to disposal, consult all applicable authorities and regulations to insure proper classification. Dispose of waste product in
a permitted industrial waste facility. If no other disposal options are available, waste product may be placed in a landfill
properly designed for industrial waste.
EPA Hazardous Waste Number (RCRA): Not regulated
SECTION 14: Transport Information
For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.
SECTION 15: Regulatory information
Post-it(R) Flag+ Highlighter Fluid - All Colors 05/09/14
__________________________________________________________________________________________
Page 8 of 9
15.1. US Federal Regulations
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - No Delayed Hazard - No
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient C.A.S. No % by Wt
ETHYLENE GLYCOL 107-21-1 10 - 30
PIGMENT Trade Secret 0 - 1
15.2. State Regulations
Contact 3M for more information.
15.3. Chemical Inventories
The components of this product are in compliance with the chemical notification requirements of TSCA.
This product is an article as defined by TSCA regulations, and is exempt from TSCA Inventory listing requirements.
Contact 3M for more information.
15.4. International Regulations
Contact 3M for more information.
This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: Other information
NFPA Hazard Classification
Health: 0 Flammability: 0 Instability: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
HMIS Hazard Classification
Health: 0 Flammability: 0 Physical Hazard: 0 Personal Protection: X - See PPE section.
Hazardous Material Identification System (HMIS® III) hazard ratings are designed to inform employees of chemical hazards
in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use
and are not intended for use in emergency situations. HMIS® III ratings are to be used with a fully implemented HMIS® III
program. HMIS® is a registered mark of the American Coatings Association (ACA).
Document Group:
19-0899-5
Version Number:
7.01
Issue Date:
05/09/14
Supercedes Date:
08/24/10
DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
Post-it(R) Flag+ Highlighter Fluid - All Colors 05/09/14
__________________________________________________________________________________________
Page 9 of 9
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR
USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable
for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product,
some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to
determine whether it is fit for a particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer
may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness
or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available
directly from 3M
3M USA SDSs are available at www.3M.com
October 06, 2017
Date:
3M ID Number:
Transport Information Document
70-0051-3353-6
Product Description:
Transport Protective Service:
NMFC Item:
179060
Flash Point (Closed-cup):
UNITED STATES DEPARTMENT OF TRANSPORTATION - GROUND (U.S. DOT, 49 CFR)
NOT REGULATED
UNITED STATES DEPARTMENT OF TRANSPORTATION - VESSEL (U.S. DOT, 49 CFR)
NOT REGULATED
Post-it(R) Flag+ Pen and Highlighter 691-HLP3
PROTECTIVE SERVICE NOT REQUIRED
NMFC Sub:
No Flash Point
02
NMFC Class:
085.0
INTERNATIONAL AIR TRANSPORT ASSOCIATION (IATA)
NOT REGULATED
INTERNATIONAL MARITIME ORGANIZATION (IMO)
NOT REGULATED
The classification is authorized by the Competent Authority of the United States of America and may not meet the requirements of other
competent authorities.
These transportation classifications are provided as a customer service. AS THE SHIPPER YOU REMAIN RESPONSIBLE FOR COMPLYING
WITH ALL THE APPLICABLE LAWS AND REGULATIONS, INCLUDING PROPER TRANSPORTATION CLASSIFICATION AND PACKAGING.
3M's transportation classifications are based on product formulations, packaging, 3M policies and 3M's understanding of applicable current
regulations and is valid for the original 3M package only. 3M does not guarantee the accuracy of this classification information. This information
applies only to transportation classification and NOT THE PACKAGING, LABELING, OR MARKING REQUIREMENTS. The original 3M package is
certified for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory requirements.
For Transport Information, please visit
or call 1-800-364-3577 or 651-737-6501 for assistance.
3M.com/Transportinfo
Loading...