⦾⦾ ELECTRICAL SPECIFICATION
ELECTRICAL SPECIFICATION
MODEL
FTPC30V12-C
FTPC30V24-C
OUTPUT
Rated Voltage
12V
24V
Rated Current
2.5A
1.25A
Rated Power
30W
Power Range
0 ÷ 30W
Line Reglation
± 1%
Load Reglation
± 2%
Voltage Tolerance [2]
± 5%
Ripple & Noise (max.) [3]
180mV
P-P
240mV
P-P
Setup, Rise, Holdup time [4]
500ms, 30ms, 15ms
INPUT
Voltage Range
180 ÷ 264VAC
Frequency Range
47 ÷ 63Hz
Power Factor (typ.)
PF > 0.9 / 230VAC at full load
Efficiency (typ.)
85%
85%
AC current (typ.)
0.22A / 230VAC
Inrush current (max.)
60A / 230VAC(25°C)
No Load Power Consumption (max.)
0.5W
PROTECTIONS
Over Current
Range: 110 ÷ 140%
Type:Type: constant current limiting to 50% rated voltage next hiccup mode. Recovers automatically
after fault condition is removed.
Short Circuit
Type: hiccup mode. Recovers automatically after fault condition is removed.
1/2
FTPC30V-C
s e r i e s
30W LED Constant voltage Switching Power Supply with PFC function
F T P C 3 0 V- C- sp e c- E N-R2 1 2 . 04. 201 7
■ Features:
• European AC Input
• Protections: Short circuit / Over current
• Cooling by free air convection
• Built-in active PFC function
• Isolation class II
• Extremely short case size
WORKING ENVIRONMENT
Working Temperature
-20°C ÷ 45°C
Working Humidity
20 ÷ 95% RH non-condensing
Storage Temperature and Humidity
-40°C ÷ 80°C, 10 ÷ 95% RH non-condensing
Temperature Coefficient
± 0.05% / °C (-10°C ÷ 45°C)
Vibration
10 ÷ 500Hz, 2G, 10min / cycle, period 30min. each along X, Y, Z axes
SAFETY AND EMC REGULATIONS
Safet Standards
Compliance to EN61347-1, EN61347-2-13
Withstand Voltage
IN/OUT: 5.3kVDC/1min
Isolation Resistance
IN/OUT: 50MΩ/500VDC/25°C/70%
EMC Emission
Compliance to EN55015
EMC Immunity
Compliance to EN61547; EN61000-4-2, -3, -4, -5, -6, -8, -11; EN55024
Harmonic Current
Compliance to EN61000-3-3; EN61000-3-2 class C ( ≥ 100% load)
OTHERS
Dimensions
156 x 50 x 17mm (L x W x H)
Weight and Packing
0.15kg; 50pcs./ctn; ctn dimensions: 25.5 x 20.5 x 16cm
EAN Code
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.
2. Tolerance incudes set up tolerance, line regulation and load regulation.
3. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1μF i 47μF parallel capacitor.
4. Setup and rise time is measured from 0 to 90% rated output voltage.
5. Power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final
equipment must be re-qualify to comply with EMC Directives.
⦾⦾ MECHANICAL SPECIFICATION
MECHANICAL SPECIFICATION
PIN ASSIGNMENT
No. Assignment No. Assignment
1 Input: AC/N 3 Output: U
OUT
-
2 Input: AC/L 4 Output: U
OUT
+
2/2
FTPC30V-C
s e r i e s
30W LED Constant voltage Switching Power Supply with PFC function
F T P C 3 0 V- C- sp e c- E N-R2 1 2 . 04. 201 7
5 9 0 2 1 3 5 1 1 7 8 9 7
5 9 0 2 1 3 5 1 1 9 2 2 8
Loading...