ELECTRICAL SPECIFICATION
MODEL
DIN100W12
DIN100W24
OUTPUT
RATED VOLTAGE
12V
24V
RATED CURRENT
8.3A
4.15A
CURRENT RANGE
0 ÷ 8.3A
0 ÷ 1.25A
RATED POWER
99.6W
VOLTAGE ADJUSTMENT RANGE [4]
10.8 ÷ 13.8V
21.6 ÷ 28V
LINE REGULATION
± 1%
LOAD REGULATION
± 1%
VOLTAGE TOLERANCE [3]
± 2%
RIPPLE & NOISE (max.) [2]
240mV
P-P
360mV
P-P
INPUT
VOLTAGE RANGE
180 ÷ 264VAC
FREQUENCY RANGE
47 ÷ 63Hz
EFFICIENCY (typ.)
87%
88%
AC CURRENT (typ.)
1.3A/230VAC
INRUSH CURRENT (typ.) 40A / 230VAC(25°C)
LEAKAGE CURRENT (max.)
1mA / 230VAC
PROTECTIONS
OVERLOAD
Range: 110 ÷ 160% rated power
Type: hiccup mode. recovers automatically after fault condition is removed
SHORT CIRCUIT
Type: hiccup mode. recovers automatically after fault condition is removed
OVER VOLTAGE
16 ÷ 23V
30 ÷ 40V
Type: shut off output voltage. Re-power on to recover.
OVER TEMPERATURE
Range: 135°C ÷ 165°C detect on main control IC
Type: shut off, recovers automatically after temperature goes down
DIN100W
s e r i e s
100W Din Rail Power Supply
D I N 1 0 0 W-spe c -EN 2 0 .02. 2 0 1 5
■ Features:
• European AC input range
•
Protections: Short circuit / Overload / Over voltage / Over temperature
• Cooling by free air convection
• Can be installed on DIN Rail TS-
35/7.5
or
15
• Isolation class II
• LED indicator for power on
ENVIRONMENT
WORKING TEMPERATURE
-20°C ÷ 50°C
WORKING HUMIDITY
20 ÷ 98% RH non-condensing
STORAGE TEMPERATURE AND HUMIDITY
-30°C ÷ 70°C, 10 ÷ 98% RH non-condensing
TEMPERATURE COEFFICIENT
± 0.05% / °C (-20°C ÷ 45°C)
VIBRATION
10 ÷ 500Hz, 2G, 10min / cycle, period for 30min. each along X, Y, Z axes
SAFETY & EMC REGULATIONS
SFAETY STANDARDS
Compliance to EN60950-1
WITHSTAND VOLTAGE
I-P/O-P: 4.2kVDC/30s
ISOLATION RESISTANCE
I-P/O-P: 100MΩ/500VDC/25°C/70%
EMC EMISSION
Compliance to EN55022
EMC IMMUNITY
Compliance to EN55024
HARMONIC CURRENT
Compliance to EN61000-3-3; EN61000-3-2
OTHERS
DIMENSIONS
100 x 93 x 56mm (L x W x H)
WEIGHT AND PACKING
0.31kg; 30pcs./box; box weight and dimensions: 10.2kg; 32.7 x 21.6 x 33.5cm
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1μF i 47μF parallel capacitor.
3. Tolerance incudes set up tolerance, line regulation and load regulation.
4. By built-in potentiometer.
5. Power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final
equipment must be re-qualify to comply with EMC Directives.
MECHANICAL SPECIFICATION
PIN ASSIGNMENT
No. Assignment No. Assignment
1 Input: AC/N 5,6 Output: U
OUT
-
2 Input: AC/L 7 LED indication for power on
3,4 Output: U
OUT
+ 8 U
OUT
adjustment
DIN100W
s e r i e s
100W Din Rail Power Supply
D I N 1 0 0 W-spe c -EN 2 0 .02. 2 0 1 5
3 4 5 61 2
8
AC/N AC /L
V+ V + V- V -
DC OK
Vout
adj.
o
INPUT:
OUTPUT:
200-240VAC 1 .4A 50/60Hz
12V 8.3A
DIN100W12
Caution s!
Do not open. Risk of electric sho ck.
For indo or use only.
7
27
46.8
56
555
8.5
5
7
100
Loading...