TM120M-A User Manual
Positioning Universal
FJ1000MV
1
FJ1000MV
Contents
1 Introduction ....................................................................................................................3
1.1ID and Tooling Design.......................................................................................................3
2 Hardware.........................................................................................................................3
2.1 Physical and Electrical Specifications ..............................................................................3
2.2 Input/Output...................................................................................................................3
2.3 Cellular Communication...................................................................................................3
2.4 Harnesses.........................................................................................................................3
2.5 Event Codes ....................................................................................................................4
2.6 System network structure...............................................................................................5
2.7 Appearance and installation instructions........................................................................5
3 USER MANUAL.................................................................................................................6
3.1 INTRODUCTION...............................................................................................................6
3.2 List...................................................................................................................................6
3.3 Description......................................................................................................................7
2
1.1 ID and Tooling Design
1. 4 wire power and I/O harness
2. 4 wire Uart
3. 14 wire power and I/O harness
Dimensions: 83.5mm*47.5mm*18mm
Weight: 60g (with optional battery)
2.1 Physical and Electrical Specifications
Input Voltage: 9-36VDC
Power consumption:
- Active mode: 100mA ＠12VDC
- Sleep mode: <8mA ＠12VDC
Operating temperature: -30℃ to 80℃
Storage temperature: -30℃to 80℃
2.2 Input/Output
Download and debug port: 1
SWD Interface: 1
Function LEDs: 2
GPS Status Green
Cellular Status Orange
Buzzer:1
FJ1000MV
2.3 Cellular Communication
Operation mode ：LTE/GPS
Operation band ：LTEB2/B4/B12;GPS 1.57542GHz
Modulation: QPSK/16QAM
2.4 Harnesses
There are 3 harnesses that may be used with the
The picture as below.
TM120M-A
:
3
FJ1000MV
Message #
Message Type
Description
0
Interval
Auto Report (auto report when moving)
1
Vibration
Vibration alarm(report when GPS is OFF and vibration detected)
2
Power Disconnect
Power cut alarm (report when external power is cut off)
3
Power Connect
Power connected alarm (external power has been connected)
4
Ignition ON
Hardwired or Virtual Ignition ON detected
5
Ignition OFF
Hardwired or Virtual Ignition OFF detected
6
Input 2 High
Input2 high alarm
7
Input 2 Low
Input2 low alarm
8
9
10
11
12
2.5 Event Codes
The table below relates the Event codes in the message to the reason the message was
generated:
4
FJ1000MV
2.6 System network structure
GPS alarm is currently the most advanced security Settings. GPS alarm more
expensive than ordinary burglar alarm, and need to pay the additional service
fee, so the popularity is not high. And alarm is based on a GPRS network
communication network, combining with the intelligent linkage of mobile phone
and car anti-theft, this kind of alarm alarm is not restricted by distance, overlay
network is wide, but need to pay the monthly rental. Buying guide to edit GPS
alarm when the choose and buy, need to pay attention to is the comparison of
several common GPS performance.
2.7 Appearance and installation instructions
3.1 Introduction.
This chapter is user manual for TM120M.
3.2 List.
1.One UART cables.
5
FJ1000MV
2.three TM120M devices.
3.One DC 12V cable.
6
FJ1000MV
3.3 Description.
1. Connect the UART cable to the UART interface of MCU on the device, the other side connect
to PC, you can communication to MCU with UART cable.
2. Connect the DC 12V cable to the connector of J203 on the device, the other side connect
to DC 12V, you can use the DC 12v cable to supply power.
7
FJ1000MV
3. The other interfaces of the TM120M device are shown in the following pictures.(The Modem
UART 2 on device is for modem debug and update firmware).
8
FJ1000MV
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
9
Loading...