FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause interference to radio communications.
It has been tested and found to comply with limits for a Class A digital device pursuant to subpart
B of Part 15 of FCC Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his owns expense will be
required to take whatever measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized technicians opens
the machine. The user should consult his/her dealer for the problem happening. Warranty voids if
the user does not follow the instructions in application of this merchandise. The manufacturer is by
no means responsible for any damage or hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex
Technology, Inc. will assume no liability for any technical inaccuracies or editorial or other errors
or omissions contained herein, nor for direct, indirect, incidental, consequential or otherwise
damages, including without limitation loss of data or profits, resulting from the furnishing,
performance, or use of this material. This information is provided “as is” and Posiflex Technology,
Inc. expressly disclaims any warranties, expressed, implied or statutory, including without
limitation implied warranties of merchantability or fitness for particular purpose, good title and
against infringement. The information in this manual contains only essential hardware concerns
for general user and is subject to change without notice. Posiflex Technology, Inc. reserves the
right to alter product designs, layouts or drivers without notification. The system integrator shall
provide applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from: http://www.posiflex.com
or
http://www.posiflex.com.tw or http://www.posiflexusa.com . All data should be backed-up prior to
the installation of any drive unit or storage peripheral. Posiflex will not be responsible for any loss
of data resulting from the use, disuse or misuse of this or any other Posiflex product. All rights are
strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise,
without prior expressly written consent from Posiflex Technology, Inc. the publisher of this
documentation.
© Copyright Posiflex Technology, Inc. 2016
All brand and product names and trademarks are the property of their respective holders.
XT– 3015/3017/3215/3215I
Fanfree LCD Touch Terminal
User’s Manual
Rev.: C0
P/N: 16640900040
Part 2
ALERT TO OUR HONORABLE CUSTOMERS:
Please always read thoroughly all the instructions and documents
delivered with the product before you do anything about it. Don’t
take any premature action before you have a full understanding of
the consequences.
This product contains inside a Lithium battery. Please always
follow local environmental protection laws / regulations for
disposal of used batteries and always replace only with battery of
same type.
If you have an UPS battery installed in the product:
Temperature above 40°C must be strictly avoided as it
could cause termination of battery life and unexpected result
even if the battery is not in work.
Do not power off the system just by shutting off the AC
power leaving the battery supporting the whole system till
completely exhausted. Repeatedly using it up or improper
maintenance reduces the battery life dramatically.
Always fully recharge the UPS battery at least once every 3
months if the battery is not connected.
Always disconnect the UPS battery from the system if the
system is to be left OFF for more than 72 hours to prevent
possible damage. Only connect the UPS battery back right
before you are going to re-power on the system.
Replace the UPS battery as soon as the monitoring software
indicates the battery is out of service. Attempt to recharge a
dead battery is dangerous!
A separate battery monitor is not required for this series.
DAILY MAINTENANCE GUIDE
For regular cleaning of the XT system, please use only soft haired brush or dry
soft cloth. You may use moist soft cloth to remove stains when necessary.
Apply only proper amount of mild neutral detergent for obstinate stains. Please
note that never use Acryl dissolving solvent or Polycarbonate dissolving
solvent. You may apply ammonia-based glass cleaner only on the screen
surface.
CAUTION
Risk of Explosion If Battery Is Replaced By An Incorrect Type
Dispose Of Used Batteries According To Local Regulations
Part 3
INTRODUCTION
PRODUCT PICTURES FOR Gen 7/E&8/E BASE STAND
Gen 7 Base
Front View Rear View
Gen 8 Base
Front View Rear View
Side View for XT-3015/3215/3215I
1 2 3 4 5
6
5
2
3 1 4
7
8 9 10
Switch Buttons
Part 4
Side View for XT-3017
Gen 7 Base
Gen 8 Base
14
15
16
18
17
20
Base Stand and Bottom View
14
15
16
Switch Buttons
12
13
11
18
19
17
Part 5
Gen 7E Base
Gen 8E Base
PARTS IDENTIFICATION
1. Main Unit
2. LCD touch panel
3. Power indicator
4. Gen 7 ,8 base stand
5. Hinge for LCD terminal
6. HDD cover
7. Power switch
8. Brightness adjust push button “+”
9. Brightness adjust push button “-”
10. USB port
11. Power switch
12. Brightness adjust push button “+”
13. Brightness adjust push button “-”
14. Cable exit
15. Base stand cover
16. Compression lock for base stand cover
17. Bottom plate
18. Rubber feet with bottom plate fixing screw
19. 2
nd
HDD cover
20. Base cover
16
15
14
16
15
14
Part 6
I/O Plate View for XT-3015/3215/3215I
A) COM1 (DB9) port
B) COM2 (DB9) port
C) COM3 (DB9) port
D) COM4 (RJ50) port
E) USB0~3 port
F) LAN1~2 port
G) VGA port
H) CR port
I) +12V UPS BAT port
J) 1 x DC IN power connector
A) CR port
B) LAN1~2 port
C) COM1~4 (DB9) port
D) USB0~7 port
E) VGA port
F) +12V UPS BAT port
G) 1 x DC IN power connector
INTRODUCING XT-3015/3017/3215/3215I
In today’s retail and hospitality market, POS terminal is no longer just a cold
and hard business tool. It is a part of the store decoration, a part of the store
B
C
D
E
F
G H I
J
A
C D E F G
I/O Plate View for XT
-3017
Loading...