POSIFLEX LT8300, TP8300 User Guide

在居住的環

可能會造成射頻干

使用者會被要

T31454

FCC Notes:

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with limits for a Class A digital device
pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable
protection against interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the user at his own
expense will be required to take whatever measures to correct the interference.

Jiva LT/TP - 8300 Touch

Terminal

User’s Manual

Rev.: A0

Warranty Limits:

Warranty terminates automatically when any person other than the authorized technicians opens
the machine. The user should consult his/her dealer for the problem happened. Warranty voids if
the user does not follow the instructions in application of this merchandise. The manufacturer is
by no means responsible for any damage or hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex
will assume no liability for any technical inaccuracies or editorial or other errors or omissions
contained herein, nor for direct, indirect, incidental, consequential or otherwise damages,
including without limitation loss of data or profits, resulting from the furnishing, performance, or
use of this material.

This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims any
warranties, expressed, implied or statutory, including without limitation implied warranties of
merchantability or fitness for particular purpose, good title and against infringement.
The information in this manual contains only essential hardware concerns for general user and is
subject to change without notice. Posiflex reserves the right to alter product designs, layouts or
drivers without notification. The system integrator shall provide applicative notices and
arrangement for special options utilizing this product. The user may find the most up to date
information of the hardware from web sites: www.posiflex.com, /www.posiflex.com.tw or
/www.posiflexusa.com.

All data should be backed-up prior to the installation of any drive unit or storage peripheral.
Posiflex will not be responsible for any loss of data resulting from the use, disuse or misuse of
this or any other Posiflex product.

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, without prior express written consent from Posiflex Technology, Inc.
the publisher of this documentation.

© Copyright Posiflex Technology, Inc. 2010

All brand and product names and trademarks are the property of
their respective holders.

警告使用者

這是甲類的資訊產品，
境中使用時，
擾，在這種情況下 ，
求採取某些適當的對策。

Part 1

ALERT TO OUR CUSTOMERS:

l Please always read thoroughly all the instructions and documents

delivered with the product before you do anything about it. Don’t
take any premature action before you have a full understanding of the
consequences.

l This product contains inside a Lithium battery and maybe also a

sealed type Lead acid battery if the UPS battery option is ordered.
Please always follow local environmental protection laws /
regulations for disposal of used batteries and always replace only
with battery of same type.

l If you have an UPS battery installed in the product:

² Temperature above 40°C must be strictly avoided as it could

cause termination of battery life and unexpected result even if the
battery is not in work.

² Do not power off the system just by shutting off the AC power

leaving the battery supporting the whole system till completely
exhausted. Repeatedly using it up or improper maintenance
reduces the battery life dramatically.

² Always fully recharge the battery at least once every 3 months if

the battery is not connected.

² Always disconnect the UPS battery from the system if the

system is to be left OFF for more than 72 hours to prevent
possible damage. Only connect the UPS battery back right before
you are going to re-power on the system.

² Replace the battery as soon as the monitoring software indicates

the battery is out of service. Attempt to recharge a dead battery is
dangerous!

² A separate battery monitor is not required for this series.

DAILY MAINTENANCE GUIDE

For regular cleaning of the Jiva systems, please use only soft haired brush or
dry soft cloth. You may use moist soft cloth to remove stains when necessary.
Apply only proper amount of mild neutral detergent for obstinate stains.
Please note that never use Acryl dissolving solvent or Polycarbonate
dissolving solvent. You may apply ammonia-based glass cleaner only on the
screen surface.

Risk Of Explosion If Battery Is Replaced By An Incorrect Type

Dispose Of Used Batteries According To Local Regulations

CAUTION

Part 2

1 3 6 5 7 2

9 9 7 10

Side Views

Gen 5

base

11 9 12

12 18 13 20

21 12 22 22

15 19 17 14

INTRODUCTION

PRODUCT PICTURES

4

Front Views

8

8

5

4

Gen 4 base

12

Gen 4 base

Gen 5 base

16

Bottom Views

Part 3

PARTS IDENTIFICATION

1. Main unit

2. Touch panel / LCD panel

3. Power status indicator

4. Base stand

5. Cable cover

6. Removal hollow in cable cover

7. Lock / release lever for tilt angle adjust

8. Optional rear top mount kit PD-302

9. Lock / release button for main unit detach

10. Power switch

11. Rear connect cover

12. Cable exit

13. 2nd cable exit

14. Rubber feet

15. Bottom plate

16. Bottom plate fixing screw

17. 2.5” HDD bracket cover in Gen 4 base

18. 2.5” HDD access window in Gen 4 base

19. Bottom plate fixing screw

20. Gen 4 base 2.5” HDD bracket fixing screw

21. Cable holder

22. Cable passage in bottom plate

PRODUCT FEATURES

Standard Features:

a) CPU: Intel 575 2.0 GHz
b) A base design supporting HDD and optional UPS battery storage
c) Support Win XP pro, WEPOS, POSReady and Linux environment
d) High quality 15” TFT active matrix LCD panel
e) Vertical type LCD panel with easy tilt angle adjustment from 15° to

70°

f) Spill proof water resistant structure allowing easy cleaning
g) Easy maintenance construction
h) Various I/O ports supported, including:

1. one PS/2 KB port

2. one PS/2 mouse port

3. 4 serial ports with capability for +5V DC support (Enable/Disable
by software or jumper control)

4. one parallel port

Part 4

5. 5 USB ports

6. one LAN port 10/100/1000 MB Ethernet

7. one external VGA port with capability for +12V DC
support(enable/disable by software setting)

8. one additional SATA connector

9. one DC 12 V power input connector

10. one UPS connector

11. one CR port for control over 2 cash drawers max.

12. one audio ports for Mic in / Line Out.

i) Touch control functions: left/right button, double click, drag & draw

(for Jiva/TP only)

j) Dual display support (Depends on OS capability)
k) VGA memory size shared from system memory (Support DVMT 5.0)
l) High performance DDR-2 667/800MHz within 2 SO-DIMM socket s,

supports maximum memory size 4GB.

m) Integrated structure for optional security devices (KP-100, SD-100 or

BC-100U)

n) Software programmable MSR parameters for Win XP pro, WEPOS

and POSReady.

Optional Items:

a) DDR-2 SDRAM memory expansion up to 4GB
b) SSD HDD
c) 2nd SATA HDD in base stand.
d) Optional RAID 1 Function for data security.
e) Infrared type touch panel.
f) Side mount upgrade kit among:

l Deluxe security device upgrade (KP100) covering keypad and

option(s) from KB interface MSR, smart card reader and finger print
sensor

l Common security device upgrade (SD100) covering option(s) from

USB interface MSR or smart card reader and finger print sensor or
iButton reader

l Bar code card reader BC-100U
g) Integrated rear top mount LCD customer display PD-300 series.
h) UPS battery
i) Preload OS
j) Customer pole display of VFD PD-2300/2500/2600 or graphic LCD

PD-302 /305/306.

k) Posiflex stand along pole display such as PD-2800/320.

Part 5

Step C:

Use plastic latch key, turn fully counterclockwise

B

l) External 12” LCD monitor LM-6101, 15” LCD Monitor LM-6501.
m) 2 in 1 cash drawer control cable
n) USB interface wireless LAN 802.11 b/g
o) Optional COM 5/6 for additional peripherals.
p) Optional 2W speakers for audio output.
q) WallMount kit .
r) Select of Gen 4 or Gen 5 Base Stand.

INSTALLATION GUIDES

CAUTION: Before any installation or cable connection to the set, please

always make certain that the system is turned off and the
external power source to the set is removed to prevent
electric hazard! Never touch any metal pin in the connectors
or circuits to avoid high voltage hazard or electrostatic
discharge damage unless the operator is well grounded.
Failure to do the above will void the product warranty!

OPENING CABLE COVER

Please follow steps A to C sequentially with reference to pictures below to
remove the cable cover for both slim and universal base models.

A

Step A: Push lock/release lever back
Step B: Turn panel to most horizontal position

then remove at both sides to release cable cover

Step D: Pull at the removal hollow toward the user

DISCONNECTING ALL CABLES

After removal of the cable cover, the connector area will be accessible then.
Please notice that the orientations of every existing cable connection first
and disconnect all cables before separating the main unit from the adjustable
stand assembly. Please note that the click lock spring has to be pressed down

C

Part 6