Posiflex TM-6100 User Manual

1

TM6100 Series

Touch Monitor

USER’S MANUAL

Rev. : Original

I. FEATURES

• Most stable touch monitor for industrial and commercial use

• Application covers POS, POI (Kiosk), Factory Automation etc.

• High quality 12.1” TFT LCD panel with scaling function for full screen display

• Resistive type extra long life touch panel

• Tilt adjustable yet robust and wobble free construction

• Spill proof and easy maintenance structure allowing easy cleaning

• Touch functions include left/right button, double click, drag & drop

• Touch beep can be pitch adjusted and enabled/disabled by software control

FCC NOTICE

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to
comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to
take whatever measures to correct the interference.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any person other than the authorized
technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow
the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.

ABOUT THIS MANUAL

This manual assists the user to utilize the TOUCH Monitor TM6000 series. These series provide versatile font
formats and support various instruction sets. These series of products receive instructions in serial communication
protocols and is capable of entering pass through mode so that all instructions received pass on to next connected serial
device if properly configured.

The manufacturer of the TM6000 series heartily apologizes to the user for reserving the right to change or to
modify this manual without notice due to the rapid and constant progress and improvement on science and technology.
The user may always obtain the most up to date information through any of our web sites: http://www.posiflex.com.tw,
http: //www.posiflexuk.com, http://www.posiflexusa.com.

TRADE MARKS AND SERVICE MARKS

POSIFLEX is a registered trademark of Mustek Corp..
Other brand and product names are trademarks and registered trademarks and service marks of their respective

owners.

 Copyright Mustek Corp. 2003

19620900020

2

II. MODEL NUMBER

TM6112: 12.1” LCD Touch Monitor on adjustable stand

TM6101: 12.1” LCD Touch Monitor w/ joining mechanism for Posiflex

touch terminals such as TP-7000 series

III. CARTON CONTENTS

1. Touch Monitor (Main unit assembled with Stand or Joint base)

2. Posiflex Product Information CDROM

3. User’s Manual

4. Power Adaptor: ASP0P042WTB001 &
power cord (for TM6112)

5. VGA Cable: 20867244100 (for TM6112)
or 20863241710 (for TM6101)

6. Touch Control Cable: 20863244210 (for
TM6112) or 20863244200 (for TM6101)

7. Harness for TM6101 to assemble onto TP7000
(separately described in later chapter)

IV. PARTS IDENTIFICATION

A. FRONT VIEW

Display Screen + Touch Panel

Power/Stand By LED

3

Power on/off Switch

n/off Switch

B. SIDE VIEWS

TM6101

TM6112

& OSD Buttons

Tilt Adjust Button

TP7000 Main Unit

TM6101

• Green: standby

• Blue: power on

C. INPUT / OUTPUT PORT

Power o
& OSD Buttons

Touch Control Port

VGA Port

D. LED INDICATION

4

Control

One end of VGA cable

V. INSTALLATION

A. For TM6112

1. Find in the rear of the panel a 10 pin RJ-45 jack for touch controller
connection and a VGA connector.

2. Connect the 10 pin RJ45 plug end of the touch control cable to the jack till it
clicks. Connect and screw fix the end with power connector of VGA cable as
in the picture.

Touch

Power Connector

VGA

Back of TM6112

Plug from Adaptor

Cables connected

3. Connect and screw fix the other end of touch control cable to an appropriate
COM port and the VGA cable to VGA port of the host system.

4. Check the specification of the power adaptor against the power socket then
insert the power adaptor into the power socket.
Connect the output plug from the power adaptor to
the connector in VGA cable

5. Press in the adjust button when turning the LCD
panel for best viewing effect in application.

B. For TM6101

Adjust Button

1. First remove the rear connect cover from the
TP7000 series base stand. Please refer to TP7000

User’s Manual and hold
your thumb gently on the
outer surface of the rear
connect cover while
having your middle finger

Rear side of TP7000 base

inside the stand assembly through the cable

Rear connect cover removed

exit to pull the plastic hook plate of the rear

5

ABCH

connect cover from inside to remove the cover.

2. Unlike other rear mount upgrade kit
for TP7000 series, TM6101 requires

F G

some extra operations. First of all,
please check all installation parts
involved. There are 2 supporting
brackets (A and B in the picture), 1
bridging bracket (C in the picture), 16

E

C

A B

D

screws with split washers (D in the
picture) besides the TM6101 on joining mechanism (E in the picture) and 2
interface cables (F and G in the picture).

3. Please then check the bottom
of the TP7000 base stand that
there are 6 screw holes near
the rear mount area as pointed
from circle marks in the
picture.

Rear bottom of TP7000

4. Check the supporting brackets that come in symmetrical pair for the 3 holes
each as pointed from circle marks in the below left picture for screw. Match
these screw holes from bottom of TP7000 series and apply 6 screws to fix
this pair of supporting brackets. Picture to the right shows bottom view of
assembled supporting brackets on TP7000 series.

Left

Right

A B

A B

Supporting brackets

Install brackets from bottom

5. Please then prepare to mount the bridging
bracket (C in the picture) in between the
supporting brackets (A and B). (We mark in the
pictures from now on the base of TP7000 series
as H in white letter for easier understanding.)