POSIFLEX SD-200 User's Manual

SD200 Series

SECURITY DEVICE

USER’S MANUAL

Rev. : A1

I. FEATURES

l Optical Finger Print Sensor in USB interface
l ISO 7811 Magnetic Stripe Reader in USB full speed HID interface
l Options for MSR heads covering 1&2, 2&3 and all 3 tracks
l 3 tracks type MSR can read also AAMVA and CA DMV card
l Total power consumption: 300 mA @ 5V DC
l There are two models. SD200 for touch terminal system and SD210

for TM-4115 monitors.

FCC NOTICE

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to
comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to
take whatever measures to correct the interference.

WARRANTY LIMITS

Warranty will terminate automatically when the equipment is opened by any person other than the authorized
technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow
the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.

The hardware utility program, including instructions for its use, is provided “AS IS” without warranty of any
kind. Posiflex Inc. further disclaims all implied warranties including without limitation any implied warranties of
merchantability or of fitness for a particular purpose. the entire risk arising out of the use or performance of the software
and documentation remains with you.

ABOUT THIS MANUAL

This manual is written in an attempt with full strength to assist the user to utilize the security upgrade kit
SD200 for the Posiflex touch terminal systems. This series of products incorporate 2 delicately designed POS peripherals
each can be used as an excellent tool to accommodate the required security specially involved in POS business, kiosk and
hospitality operation. This manual covers the conceptual and operational aspects of these units. For technical aspects
involving opening of the unit or option implementation, it is only available to the authorized distributors.

The manufacturer of the SD200 series heartily apologizes to the user for reserving the right to change or to
modify this manual without notice due to the rapid and constant progress and improvement on science and technology.
The user may always obtain the most up to date information through any of our web sites: http://www.posiflex.com or
http://www.posiflex.com.tw.

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system,
or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written
consent of Mustek Corp. the publisher of this documentation

TRADE MARKS AND SERVICE MARKS

POSIFLEX is a registered trademark of Posiflex Inc., an ISO-9001 and ISO-14001 certified manufacturer.
Other brand and product names are trademarks and registered trademarks and service marks of their respective

owners.

 Copyright Posiflex Inc. 2004

P/N: 19090900030 1

II. INSTALLATION

1. HARDWARE INSTALLATION

For SD200 series ordered with the host system like Jiva series (except Jiva
5800 series before the Jiva 5800G version) or TM4115 series, it is installed on
the system at delivery. For separately ordered SD200 series, it is delivered
separately from the system and needs to be fixed onto the system (also not
recommended for Jiva 5800 series before the Jiva 5800G version) per following
instructions before use. However, before trying to install a SD200, please check
first that there is one free USB connector in the I/O area of the system reserved
for this purpose in the system configuration. Should there be any need for
application of a USB HUB for this connection, a self-powered type USB HUB
(with its own power adaptor) is required. However, For SD210 application with
TM4115, Please connect the unit to the extension cable in cable cover area of
TM4115 and then connect the extension cable to the USB port of the host system.

You may find two screw holes on back of the right side of the main unit of
Jiva series or TM4115 series. Align the upgrade unit to the right edge of the
main terminal. Insert and fasten with the two screws with split washers included
in your kit, as indicated in the picture below.

Upgrade Unit Screw Holes

Back of Jiva Series

The Upgrade Kit

2. DRIVER INSTALLATION

1. For Finger Print Sensor: To include the drivers for this sensor to perform

finger print registration or verification (authentication) in an AP requires the

software programmer to purchase and utilize its SDK (software developer’s

kit). However, Posiflex delivers this optical finger print sensor with its

drivers. Please find in the mini CD delivered with SD200 or Product

Information CD delivered with Posiflex POS system the folder for “Posiflex

2