POSIFLEX PST-7000 User's Manual

LP

L3

L0

PST-7000 Series

USER’S MANUAL

Rev. A

L4

L3

SOME IMPORTANT NOTICES

FCC NOTICE

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits
for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection
against interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to
cause interference in which case the user at his own expense will be required to take whatever measures to correct the
interference.

WARRANTY

This equipment contains no user serviceable parts and as such should be only opened by authorized technicians,
failure to comply with this will void any warranty that is in force. The user should consult an authorized dealer or representative
of Posiflex if the equipment fails to perform according to expectation.

equipment.

SAFETY

electrical safety regulations.

and disposed of in a safe manner without hazard to the environment and again in a manner that is consistent with the local
regulations for health and safety.

SUPPLEMENTAL NOTICES

supplemental documentation to conform to the legal and other requirements of sale within the intended region. Please make sure
that any Supplemental Notices shipped with this equipment are consulted before any installation procedures are attempted

DISCLAIMER:

any errors or omissions. It is the responsibility of the user to ascertain that the equipment is suitable for the intended purpose and
to take adequate steps to safeguard data and to comply with the law.

constitute a description of any goods or services nor a commitment on behalf of the manufacturer.

ABOUT THIS MANUAL

POSIFLEX integrated point-of-sale terminal product family. The PST7000 is a compact point-of-sale system that utilizes the
most up-to-date technology in POS business machine and combines the performance and affordability of personal computers
with the elegance and reliability of business machine. The PST7000 also provides the built-in networking capability for easy
communication among multiple terminals in addition to the data transfer and control through back office server.

this manual without notice due to the rapid and constant progress and improvement on science and technology. The user may
always obtain the most up to date information through our web site: http://www.posiflex.com.tw/ or http://www.posiflexuk.com/
or http://www.posiflexusa.com/

The manufacturer cannot be held responsible for any damage caused or any hazard generated by improper use of this

This equipment should be connected to the main power source in a safe manner and should conform to the local

This equipment also contains batteries of one or more types of chemistry. It is important that they are stored, handled

Additional information may be available in the Supplemental Notices.

The Posiflex range of PST terminals are designed for use on a worldwide basis and as such may be required to carry

Considerable effort has been taken to ensure accuracy in compiling this manual but no liability can be accepted for

The details for hardware and software quoted in this manual are liable to change without notice. They do not

The above statements do no affect your statutory rights.

This manual assists the user to install and to utilize the hardware of the PST7000 series which is a member of the

The manufacturer of the PST7000 series heartily apologizes to the user for reserving the right to change or to modify

© Copyright Mustek Corp. 2000

transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent
from Mustek Corp. the publisher of this documentation.

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or

TRADE MARKS AND SERVICE MARKS

POSIFLEX is a registered trademark of Mustek Corp..

Other brand and product names are trademarks and registered trademarks and service marks of their respective
owners.

This equipment conforms to the requirements of 89/336/EEC. Please see supplemental notices and additional information.

CMANUPST7000

TABLE OF CONTENTS

BRIEF INTRODUCTION · · · · · · · · · · · · · · · · · · · · 1 - 1

THE USER’S MANUAL· · · · · · · · · · · · · · · · · · · · 1 - 1

THE PRODUCT · · · · · · · · · · · · · · · · · · · · · · · · 1 - 2

OVERVIEW · · · · · · · · · · · · · · · · · · · · · · · · 1 - 2
CONFIGURATION · · · · · · · · · · · · · · · · · · · · 1 - 2

THE BASIC POSiFLEX MODELS· · · · · · · · · · · · · 1 - 2
THE STANDARD FEATURES · · · · · · · · · · · · · · 1 - 3

Easy Accessible Service Windows · · · · · · · · · · 1 - 3
Non-Volatile Memory · · · · · · · · · · · · · · · 1 - 3
Ethernet Networking · · · · · · · · · · · · · · · ·1 - 3
Numerical Keypad · · · · · · · · · · · · · · · · 1 - 3
Keyboard Memory · · · · · · · · · · · · · · · · 1 - 3
6 Position Key Switch· · · · · · · · · · · · · · · 1 - 3
Direct Controlled Cash Drawer Port· · · · · · · · · · 1 - 4
Customer Display Port· · · · · · · · · · · · · · · 1 - 4
Cashier Display Port· · · · · · · · · · · · · · · · 1 - 4
Serial Ports · · · · · · · · · · · · · · · · · · · 1 - 4
Parallel Port · · · · · · · · · · · · · · · · · · · 1 - 4
USB Device Connection · · · · · · · · · · · · · · 1 - 4
Modem Ring-Up, LAN And Alarm Wake Up · · · · · · 1 - 5
UPS Function · · · · · · · · · · · · · · · · · · 1 - 5

THE OPTIONAL ITEMS · · · · · · · · · · · · · · · · 1 - 5

MSR · · · · · · · · · · · · · · · · · · · · · · 1 - 5
Customer Display · · · · · · · · · · · · · · · · · 1 - 5
Bar Code Scanner · · · · · · · · · · · · · · · · ·1 - 5
Audio Line Output Port · · · · · · · · · · · · · · 1 - 5
PCMCIA Control Board · · · · · · · · · · · · · · 1 - 5
2-in-1 Cash Drawer Control Cable · · · · · · · · · · 1 - 6
DRAM Memory Expansion · · · · · · · · · · · · · 1 - 6

i

Variety of Key Tops · · · · · · · · · · · · · · · · 1 - 6
QWERTY Keyboard · · · · · · · · · · · · · · · ·1 - 6
POS Printer · · · · · · · · · · · · · · · · · · · 1 - 6
UPS Battery · · · · · · · · · · · · · · · · · · · 1 - 6
Integrated CD ROM Drive · · · · · · · · · · · · · 1 - 7

SYSTEM BOX CONTENTS · · · · · · · · · · · · · · · · · 1 - 7

MAIN SYSTEM UNIT · · · · · · · · · · · · · · · · · · · 1 - 7
CASHIER DISPLAY CARTON · · · · · · · · · · · · · · ·1 - 7
CUSTOMER DISPLAY CARTON · · · · · · · · · · · · · 1 - 7
PST ACCESSORIES CARTON· · · · · · · · · · · · · · · 1 - 8

PARTS IDENTIFICATION · · · · · · · · · · · · · · · · · · · 2 - 1

INSTALLATION GUIDES· · · · · · · · · · · · · · · · · · · ·3 - 1

IMPORTANT· · · · · · · · · · · · · · · · · · · · · · · · · · 3 - 1

SERVICES WINDOWS · · · · · · · · · · · · · · · · · · · · 3 - 1

PUTTING IN UPS BATTERY · · · · · · · · · · · · · · · · 3 - 4

MONITOR · · · · · · · · · · · · · · · · · · · · · · · · · · · 3 - 4

LCD CASHIER DISPLAY · · · · · · · · · · · · · · · · · · 3 - 7

CUSTOMER DISPLAY · · · · · · · · · · · · · · · · · · · · 3 - 8

PROGRAMMABLE KEYBOARD · · · · · · · · · · · · · ·3 - 9

INTERNAL KB WEDGE BARCODE SCANNER · · · · · 3 -14

INTERNAL CONNECTION · · · · · · · · · · · · · · · · 3 -14

PS/2 MOUSE · · · · · · · · · · · · · · · · · · · · · · · · · · 3 -16

PRINTER · · · · · · · · · · · · · · · · · · · · · · · · · · · · 3 -17

AUDIO LINE OUTPUT · · · · · · · · · · · · · · · · · · · ·3 -18

CASH DRAWER · · · · · · · · · · · · · · · · · · · · · · · · 3 -19

AC POWER · · · · · · · · · · · · · · · · · · · · · · · · · · · 3 -20

USING THE PST SYSTEM · · · · · · · · · · · · · · · · · · · 4 - 1

BEFORE POWER ON · · · · · · · · · · · · · · · · · · · · 4 - 1

VENTILATION · · · · · · · · · · · · · · · · · · · · · · 4 - 1
OPERATING ENVIRONMENT · · · · · · · · · · · · · · 4 - 1

ii

POWER SUPPLY· · · · · · · · · · · · · · · · · · · · · · 4 - 1
PRINTER DC POWER SUPPLY · · · · · · · · · · · · · · 4 - 1
VGA DISPLAY PORT · · · · · · · · · · · · · · · · · · · 4 - 2
CUSTOMER DISPLAY· · · · · · · · · · · · · · · · · · · 4 - 2
SERIAL PORT – COM1 · · · · · · · · · · · · · · · · · · 4 - 2

MONITOR (FOR PST7000/PST7300) · · · · · · · · · · · ·4 - 3

MECHANICAL OPERATION · · · · · · · · · · · · · · · 4 - 3
TURN ON THE MONITOR · · · · · · · · · · · · · · · · 4 - 4
DISPLAY CONTROLS· · · · · · · · · · · · · · · · · · · 4 - 4

CONTRAST CONTROL· · · · · · · · · · · · · · · · · 4 - 4
BRIGHTNESS CONTROL · · · · · · · · · · · · · · · · 4 - 4
HORIZONTAL PHASE CONTROL· · · · · · · · · · · · 4 - 4
VERTICAL SIZE CONTROL· · · · · · · · · · · · · · · 4 - 5

DISPLAY UTILITY DRIVER· · · · · · · · · · · · · · · ·4 - 5

LCD (FOR PST7030/PST7350) · · · · · · · · · · · · · · · ·4 - 6

MECHANICAL OPERATION · · · · · · · · · · · · · · · 4 - 6
DISPLAY UTILITY DRIVER· · · · · · · · · · · · · · · ·4 - 7

CUSTOMER DISPLAY · · · · · · · · · · · · · · · · · · · · 4 - 7

VERSATILE MECHANICAL MANEUVERABILITY · · · 4 - 7

PROGRAMMABLE KEYBOARD · · · · · · · · · · · · · ·4 - 8

BASIC FUNCTIONS · · · · · · · · · · · · · · · · · · · · 4 - 9
STRUCTURE· · · · · · · · · · · · · · · · · · · · · · · · 4 - 9
6 POSITION KEY-LOCK· · · · · · · · · · · · · · · · · · 4 -11
APPLICATION EXAMPLE · · · · · · · · · · · · · · · · 4 -13

EXAMPLE 1· · · · · · · · · · · · · · · · · · · · · · 4 -13
EXAMPLE 2· · · · · · · · · · · · · · · · · · · · · · 4 -14
FURTHER IDEAS · · · · · · · · · · · · · · · · · · · 4 -14

SPECIAL FEATURES · · · · · · · · · · · · · · · · · · · 4 -15

SECURITY LOCK OFF · · · · · · · · · · · · · · · · · 4 -15
MULTI-PAGE PROGRAMMING · · · · · · · · · · · · · 4 -15
MULTI-LEVEL PROGRAMMING · · · · · · · · · · · · 4 -15
ANSWER BACK · · · · · · · · · · · · · · · · · · · · 4 -15
SPEED CONTROL OF OUTPUT · · · · · · · · · · · · · 4 -16

iii

TIME CONTROL ON OUTPUT HOLD · · · · · · · · · · 4 -16
SOFTWARE SWITCH OFF · · · · · · · · · · · · · · · 4 -16
CONVENIENCE IN PROGRAMMING· · · · · · · · · · ·4 -16
INSTANT CONTENT UPDATE · · · · · · · · · · · · · 4 -17

PRELOADED KEY DEFINITIONS· · · · · · · · · · · · · 4 -18

MSR · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4 -21

LED INDICATORS · · · · · · · · · · · · · · · · · · · · · · 4 -22

FRONT DOOR · · · · · · · · · · · · · · · · · · · · · · · · · 4 -23

EXTERNAL PC KBYBOARD · · · · · · · · · · · · · · · · 4 -23

3.5” FDD · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4 -23

POWER ON/OFF CONTROL · · · · · · · · · · · · · · · · 4 -24

EXTERNAL POWER ON SWITCH · · · · · · · · · · · · 4 -24
POWER ON/OFF PUSH SWITCH · · · · · · · · · · · · · 4 -24
SOFTWARE OFF SWITCH · · · · · · · · · · · · · · · · 4 -24
PRESET POWER ON CONTROL · · · · · · · · · · · · · 4 -25
EMERGENCY POWER OFF · · · · · · · · · · · · · · · ·4 -25

REAR ROOM· · · · · · · · · · · · · · · · · · · · · · · · · · 4 -26

PRINTER · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4 -26

USB· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4 -26

BUILT-IN UPS WITH BATTERY · · · · · · · · · · · · · · 4 -26

iv

PST-7000 series user’s manual – BRIEF INTRODUCTION

BRIEF INTRODUCTION

THE USER’S MANUAL

The purpose of this manual is to guide the user in the initial installation and
general use of the Posiflex PST7000 series of POS terminals. It does not, however,
make any attempt to explain any application software that may be supplied with it and
which of course is an essential component of any system.

We intend to provide our customers with all the advantages made available in
the advances of electronic technology by evolving the product design to incorporate
appropriate changes and improvements, as such some detail differences may exist
between this manual and the equipment supplied.

The latest information on this terminal and our other products is available from
our authorized dealers or on our web site. Details of the latter are printed in our
supplemental notices and additional information.

1 - 1

PST-7000 series user’s manual – BRIEF INTRODUCTION

THE PRODUCT

Overview

The Posiflex range of PST7000 terminals have been designed and
manufactured to meet the high end demand on POS system.

The PST range incorporates all the advances of personal computer technology
within a rugged housing designed for use in a hostile retail environment. By providing
an integrated design, Posiflex has retained many of the secure features of a traditional
ECR and has avoided the wiring “spaghetti” associated with more traditional PC
solutions.

The system architecture conforms to both the original open ISA standard
(outlined in IEEEP996) and to the newer PCI bus standard. This Open Standard
Architecture ensures that this terminal can use the very wide range of PC application
software and development tools that are now inexpensively available and abundant.

The terminal may be used as a self-contained unit or by using the integrated
network interface as one of several terminals in a network system controlled by a
“back office” computer.

Configuration

The PST7000 terminal may be supplied as one of several models and may also
have a number of optional items added to it. These may be from the Posiflex range or
from other suppliers but because of the Open System Architecture, compatibility will
in general not be an issue.

THE BASIC POSIFLEX MODELS ARE:

• PST7000 – supplied with the capability to support a VGA CRT monitor and a

matrix programmable keyboard

• PST7050 – supplied with a 12” color TFT LCD display installed and a matrix

programmable keyboard

• PST7300 – supplied with the capability to support a VGA CRT monitor and a

PC layout programmable keyboard

1 - 2

PST-7000 series user’s manual – BRIEF INTRODUCTION

• PST7350 – supplied with a 12” color TFT LCD display installed and a PC layout

programmable keyboard

THE STANDARD FEATURES ARE:

Easily Accessible Service Windows

There are several windows in bottom chassis for RTC battery easy
replacement, COM port power enable/disable easy setting, SO-DIMM upgrade and 1
IDE HDD replacement.

Non-Volatile Memory

The standard non-volatile memory of PST7000 series is 32 KB. This non­volatile memory is used by the software system provider to safeguard the data storage;

st

or, if worked in cooperation with the system integrator, can be used for fiscal memory
systems.

Ethernet Networking

The standard network port works with both 10 Base T and 100 Base T.

Numerical Keypad

The standard keyboard (112 keys) layout in PST7000 series contains an area
for numerical keypad for easier numerical inputs.

Keyboard Memory

The standard keyboard memory of the programmable keyboard of PST7000
series is 8 KB.

6 Position Key Switch

Every PST7000 system is equipped with a 6 position key switch for several
purposes. This key switch supports security lock off and multi-page programming of
the programmable keyboard, answer back code and software switch off functions. 4
different type of keys are provided for different accessibility.

1 - 3

PST-7000 series user’s manual – BRIEF INTRODUCTION

Direct Controlled Cash Drawer Port

There is one direct controlled cash drawer port in the rear room of each
PST7000 system. This port controls one cash drawer (mostly recommended with the
CR3X00/CR4X00) with the standard accessory cable CCBLA-180. This port can
control two cash drawers independently using the optional cable CCBLA-238.

Customer Display Port

Every PST system provides a customer display port to drive any Posiflex
customer display. However, the system case with a base tube of a customer display is
different from that without a customer display.

Cashier Display Port

The cashier display ports utilized in PST7000/7300 and PST7050/7350 are
different to each other. The monitor used in PST7000 and PST7300 is connected to a
3 x 5 D VGA connector while the TFT LCD used in PST7030 and PST7350 is
connected to a 26 pin SCSI type specialized connector. Both connectors exist and
function on any of the models.

Serial Ports

There are 4 serial ports in a PST7000 system. COM1 is shared by the customer
display port and the direct driven cash drawer port. COM1 is capable of providing a
+5 V DC supply. COM2, COM3 and COM4 each are capable of providing
independently a +5 V DC or a +12 V DC supply. All these DC supplies are achieved
through internal jumper setting and they are all defaulted to give no DC supply at
delivery. The COM3 and COM4 ports can be disabled by internal jumper setting if
any resource conflict occurs between any added adapter card and these 2 ports.

Parallel Port

Each PST system is equipped with a parallel port that supports SPP/EPP/ECP.

USB Device Connection

The PST7000 series is equipped with two connectors for connection of USB
(Universal Serial Bus) devices.

1 - 4

PST-7000 series user’s manual – BRIEF INTRODUCTION

Modem Ring-Up, LAN And Alarm Wake-Up

The PST7000 series can be turned on automatically upon an incoming COM
port Modem call or LAN status or data packet received on LAN or a preset
time/day/week/month.

UPS Function

The PST7000 series has a built-in UPS function that will protect the system
from accidental AC power failure if an optional UPS battery is installed.

THE OPTIONAL ITEMS ARE:

MSR – Magnetic Stripe Card Reader supplied as:

• 2 track reader (track 1 & 2)

• 2 track reader (track 2 & 3)

• 3 track reader (track 1, 2 & 3)

Please note that the card slot is always present whether or not the MSR is

fitted. A blanking module is fitted in place of the MSR if the MSR is not supplied.

Customer Display – This can be supplied in a variety of types:

• 2 line by 16 character LCD display (PD201)

• 2 line by 20 character VFD display (PD2101/PD2201)

• Graphic LCD display (PD7101)

Bar Code Scanner

• CCD scanner (CD-2800K) with 80mm width read capability

• Laser Scanner (LS6080K/LS6060K)

Audio Line Output Port

This option requires different mainboard and should be ordered before the
delivery. For application of this option, a pair of booster speakers are recommended.

PCMCIA Control Board (PST060)

This board works on the PCI bus slot of the PST7000 system and accepts type
II or type III PCMCIA card.

1 - 5

PST-7000 series user’s manual – BRIEF INTRODUCTION

2-in-1 Cash Drawer Control Cable

This cable CCBLA-238, when added to the CR port of the PST7000 series,
can be used to control two Posiflex CR-3100 or CR-3200 or CR-4000 cash drawers.

DRAM Memory Expansion

The standard memory size is 32 MB and can be expanded to 512 MB in 2 SO-

DIMM modules.

Variety of Key Tops

• Quad Key

• Horizontal Double Key

• Vertical Double Key

• Single Key

• Blank Key

QWERTY Keyboard

The standard equipped programmable keyboard is a 112 keys matrixed
programmable keyboard. The optional “QWERTY” layout keyboard provides a more
type-writer-like area plus a numerical keypad and 53 programmable keys. This option
is available for France, Germany, Italy, Netherlands,Portugal, Spain, Sweden/Finland,
United Kingdom or United States.

POS Printer

• PP-1000 series Posiflex POS printers: friction paper feed, serial or parallel

interface, single or dual color printing, 7 pin dot matrix impact printer.

• PP-2000 series Posiflex POS printers: friction paper feed, serial or parallel

interface, 2 stations 9 pin dot matrix impact printer.

• PP-3000 series Posiflex POS printers: friction or sprocket paper feed, serial or

parallel interface, 9 pin dot matrix impact printer

• PP-4000 series Posiflex POS printers: friction paper feed, serial or parallel

interface, line thremal printer.

UPS Battery

2.3 AH 12V Lead Acid Battery

1 - 6

PST-7000 series user’s manual – BRIEF INTRODUCTION

Integrated CD ROM Drive

This option includes case modification and should be ordered berfore delivery.

SYSTEM BOX CONTENTS

When you receive the system box you will find it contains several items:

• Main system unit

• Cashier display carton for LCD model PST7050 or PST7350

• Customer display carton if an option of customer display is ordered

• PST accessories carton

• Other optional components as ordered.

Main System Unit

The main system unit is supplied with the key tops of the programmable

keyboard assembled without the transparent key caps.

Cashier Display Carton

When the order is PST7000 or PST7300, the purchased VGA mono or VGA
color monitor will be shipped in a separate box from the main system unit. When the
order is PST7050 or PST7350, the package for the 12.1” color TFT LCD is inserted in
a side within the system box.

Customer Display Carton

This is a separate carton within the main carton and contains the customer

display (sometimes called a pole display) when an option of customer display is
purchased with the PST system.

1 - 7

PST-7000 series user’s manual – BRIEF INTRODUCTION

PST Accessories Carton

This contains most of the small parts and loose items for PST7000 and

PST7050 as follows:

• This user’s manual

• 1 set of keys (4 pieces) for keyboard key switch

• 1 set of keys (2 pieces) for front door lock

• Keyboard type dependent accessories as listed below

• 3½ inch diskette (4 pieces) with driver utilities

• Cable tie (5 pieces)

• Velcro patches (4 pieces) for printer installation.

• VFD terminator (1 piece)

• COM1 terminator (1 piece)

• Main power cord (1 piece)

• Cash Drawer cable (CCBLA-180) (1 piece)

• Printer power cable (1 piece)

• Dust cover (1 piece)

The content of keyboard type dependent accessories is listed below. Please
note that these parts are different in size between the KB112 for PST7000/PST7050
and the KB136 for PST7300/PST7350. The rough measurements in millimeters of the
key surfaces are also noted below:

PST7000/PST7050 PST7300/PST7350

Accessories for models

Qty Note Qty Note

Legend sheet in 4 colors (set) 1

P/N:CLABPSTK
B112-1

P/N:CLABPSTH

1

KB112
Key cap removal tool (key clip) 1 P/N:QC2000 1 P/N:QCH2000
Single key transparent cap 92 22 x 18 52 18 x 18
Vertical double key transparent cap 2 22 x 37 1 18 x 37
Horizontal double key transparent cap 0 45 x 18 0 37 x 18
Quad key transparent cap 1 37 x 45 (not applicable)
Blank key 2 22 x 18 (not applicable)

1 - 8

options.

L3

¬

-

®

¯

°

±

²

³

´

PST-7000 series user’s manual –PARTS IDENTIFICATION

PARTS IDENTIFICATION

The following pictures show in detail the assembly of PST terminals and

MAJOR PARTS OF
PST7000 CRT MODEL:

POWER ON SWITCH KNOB

¬

PROGRAMMABLE

-

KEYBOARD

POSITION KEY SWITCH

®

CASHIER DISPLAY

¯

(MONITOR)

CUSTOMER DISPLAY

°

(OPTIONS INCL. PD-2101,
PD-2201 or PD-7001/7101)

OPTIONAL PRINTER

±

OPTIONAL MSR

²

FRONT DOOR

³

FRONT DOOR LOCK

´

Fig. 2 - 1 Major parts seen from front of CRT model

(PST7000/7300)

2 - 1

PST-7000 series user’s manual – BRIEF INTRODUCTION

L1L1

L0L0
LPLP

L3L3

L4L4

¬

-

®

¯

°

²

±

³

´

MAJOR PARTS OF
PST7050 LCD MODEL:

POWER ON SWITCH KNOB

¬

PROGRAMMABLE KEYBOARD

-

POSITION KEY SWITCH

®

CASHIER DISPLAY (LCD)

L2L2

¯

CUSTOMER DISPLAY

°

(OPTIONS INCL. PD-2101,
PD-2201 or PD-7001/7101)

OPTIONAL PRINTER

±

OPTIONAL MSR

²

FRONT DOOR

³

FRONT DOOR LOCK

´

Fig. 2 - 2 Major parts seen from front of LCD model

(PST7050/7350)

2 - 2

PST-7000 series user’s manual –PARTS IDENTIFICATION

¬

-

®

¯

°

±

²

³

´

µ

DETAIL PARTS:

CRT MONITOR

¬

CABLE COVER

-

MONITOR HOOK

®

BOWL SHAPED

¯

TILT BASE

MOUNTING LUG

°

SWIVEL BASE

±

SWIVEL BASE

²

HANDLE

11

DISPLAY

³

PLATFORM

INNER POLE

´

BASE TUBE

µ

11

RAIL COVER

L4

L3
L2
L1

L0

LP

Fig. 2 - 3a Detail parts seen from front of CRT model

2 - 3

PST-7000 series user’s manual – BRIEF INTRODUCTION

¬

-

®

°

±

²

³

´

µ

¯

µ

L4L4

L3L3
L2L2
L1L1

L0L0

LPLP

DETAIL PARTS:

POWER ON INDICATOR (GREEN)

¬

STAND-BY INDICATOR (ORANGE)

-

KEY TOPS WITH TRANSPARENT KEY CAPS

®

VENTILATION OPENINGS

¯

TUBE COVER

°

BATTERY COMPARTMENT COVER

±

PRINTER PLATFORM

²

MSR INDICATOR (OPTION)

³

MSR SLOT

´

MSR READER HEAD INDICATOR

Fig. 2 - 3b Detail parts seen from front of CRT model

2 - 4

PST-7000 series user’s manual –PARTS IDENTIFICATION

EXTERNAL KEYBOARD PORT

(5 P DIN JACK)

POWER ON/OFF
PUSH SWITCH

3.5” FDD

Fig. 2 - 4 Inside the front door

VENTILATION
OPENINGS

DISPLAY
PLATFORM

VGA CABLE

MONITOR

CABLE COVER

BACK DOOR
LATCH

PRINTER
PLATFORM

BATTERY
COMPARTMENT
COVER

BACK DOOR
LATCH

BACK DOOR

Fig. 2 - 5 Rear view of PST (CRT model in this example)

2 - 5

PST-7000 series user’s manual – BRIEF INTRODUCTION

AC VOLTAGE SELECTION SWITCH

USB 2

LPT 1

CR

LCD
DISPLAY

24 VDC

CUSTOMER DISPLAY
(PD-2101/2201/7001)

VGA USB 1

Fig. 2 – 6 Inside the back door

AC INLET

LAN

COM 2

COM 4

COM 3

COM 1

Fig. 2 – 7 The integrated CD-ROM

2 - 6

PST-7000 series user’s manual – INSTALLATION GUIDES

INSTALLATION GUIDES

IMPORTANT

PLEASE DO NOT CONNECT THE POWER CORD OR TURN ON
THE MAIN UNIT UNTIL YOU HAVE FULLY READ THE INSTALLATION
GUIDES AND FOLLOWED THE INSTRUCTIONS!!!

SERVICE WINDOWS

At the bottom of PST7000 terminals, there are four service windows that can
be opened for hardware upgrade/installation without the need to open the whole
structure. Please refer to the bottom view picture below for locations of these
windows and their fixation screws.

In the COM port jumper setting window, there are jumpers

for defining how the power supply to COM ports are organized.

1 Fixation Screw for Window
for COM Port Jumper Setting

4 Fixation Screws for Window
for 1st IDE HDD

5 Fixation Screws for Window
for System Battery & DRAM

1 Fixation Screw for Window
for UPS Battery Connector

Please have the jumpers changed only by a qualified technician
who can take appropriate action under the guidance from the
Technical Manual of this product series. Screw back the cover

plate by first inserting the opposite edge from the screw hole to the bottom chassis.

3 - 1