P/N:
1949
09000
40
PD - 7600 Series Customer Display
FCC Notes:
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with limits for a Class A
digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims
any warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
http://www.posiflex.com or http://www.posiflex.com.tw
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Inc. the publisher of this documentation.
© Copyright Posiflex Technology, Inc. 2011
All brand and product names and trademarks are the property of their respective holders.
User’s Manual
Rev. C0
Part 1
BRIEF INTRODUCTION
THE PRODUCT
The PD-76X0 is a stand alone pole mount customer display designed for
discrete POS applications, The PD-76X4 is a Rear-base pole mount customer
display option designed for XP series POS terminals and Gen.6 base stand for
KS series & Gen.4.5 for LM series. The PD-7600 series utilizes a graphical
LCD module with backlight. It supports 4 rows display of 15 Chinese or 30
Arabic characters each in format of 16 by 16 dots or 8 by 16 dots respectively.
FEATURES
• Graphic STN LCD (liquid crystal display) in blue background with
white backlight
• Stand alone Pole Display for POS application (PD-76X0)
• Four-line display with 30 Arabic letters or 15 Chinese characters
per line
• 240 by 64 dots for graphic display
• Adequately sized characters for easy viewing (8.47 mm by 4.24
mm per digit)
• Long life and trouble free operation
• Display contrast adjust buttons on front surface
• 15°, 30° and 45° adjustable viewing angles
• Display frame can rotate horizontally 270° freely
• Supports ESC/POS commands
• Simple installation
• Serial (RS232) interface for PD-76X0; RJ45 interface for PD-76X4
• Case color choices: ivory, black
MODELS, LANGUAGES & CODE TABLES
Stand Alone Pole Mount model:
• PD-7610: Simplified Chinese, GB-2312
• PD-7620: Traditional Chinese, BIG-5
• PD-7630: Arabic, Windows code page 01256 (with Arabic
numerals addressed in <80> ~ <89> of code page 1)
• PD-7640: Hindi.
Rear-Base Pole Mount model:
• PD-7614: Simplified Chinese, GB-2312
• PD-7624: Traditional Chinese, BIG-5
• PD-7634: Arabic, Windows code page 01256 (with Arabic
numerals addressed in <80> ~ <89> of code page 1)
Part 2
24 VDC
INSTALLATION GUIDES
PACKAGE CONTENTS
The pole display with base or pole display with fix bracket
The User’s manual
RS-232 signal cable (for PD-76X0)
Power adaptor per country type ordered (for PD-76X0)
Self-tapping screws for PD-76x4 use in Gen.4.5 base stand.
Bing Head Screw for Gen 6 of KS series and XP series.
PHYSICAL INSTALLATION
Stand Alone Pole Mount model:
Find a flat surface to site the base of the display for application operation. Find
in the bottom of the base the connectors as in the drawing below:
To Display head
The RJ45 type modular connector is for internal use and is already occupied.
The RS232 input port is a DB9 female connector. Connect the attached RS232 signal cable to this port and one of the COM port in the host system. Set
the RS-232 communication protocol for this port to 9600 bps, no parity, 8 bits,
1 stop bit with hardware handshaking. Connect the power adaptor to the
rightmost power connector. Turn on the switch in the front side of the base.
Rear-Base Pole Mount model:
The PD-76X4 can be attached to either rear corner
of bottom plate of XP series and Gen.6, Gen.4.5
base stands of KS series. Firstly, it takes XP series
for example. Please aim the hole to the arrowed
screw which shows in the right picture. Use the 3
attached Bing head screws to fix the metal base plate
of the PD to the bottom of XP series base as circled
in the picture. Arrange the interface cable to go through under bottom to XP
series system connector area. Adjust the direction of the display head for best
viewing effect in application. For integrated to the Gen.4.5 base stand, please
aim to the holes which marked “DT” and use the self-tapping screws to fix on
the Gen.4.5 base.
RS232 input
12 VAC input
Part 3
Stand Alone Model:
This instruction is for stand alone model only. Please
unpack the inner box of pole display and it easy to find
the base, display unit with tube and adaptor separately.
Please remove the PE foam and bring out the components
carefully.
Firstly, place the display head and tube on a flat surface
and find the cable which in the end of tube. Let this cable
pass through the short tube which on the base stand and it
shows in the picture at right.
Next, please assemble the display head with tube to the
base stand which shows in the right picture. Please pay
more attention during the process since there is a hole and
a compression lock which are in the two side of tube and
marked arrow signs. Aim these two arrow signs nearby
compression lock to the holes and push the tube to the end.
After hear the “click” sound, the assembly is complete.
Once combine the display head with tube and base stand,
please place the pole display as a horizontal position
which can easily to check the bottom plate.
Please plug the cable to the connector which showing “To
Display” and route the cable as arrowed in the right
picture.
DRIVER INSTALLATION
For application software to use the RS232 interfaced PD-7600 series, there is
no direct need for any driver.
APPLICATION GUIDES
CONTRAST ADJUST
Use the 2 buttons on right side of the display head front
surface to increase / decrease the contrast of LCD
Part 4
COMMAND LIST
Command Hex Code Function
ESC DC1 <1B><11>
US MD1 <1F><01>
ESC DC2 <1B><12>
US MD2 <1F><02>
CLR <0C> Clear Display Screen
ESC @ <1B><40> Initialize Display
ESC _ n <1B><5F><n> Set Cursor ON/OFF (n=0,1)
US r n <1F><72><n> Select/Cancel Reverse Character (n=0,1)
ESC = n <1B><3D><n> Data Display Select (n=1,2)
US T h m <1F><54><h><m> Set Time (0≤h≤0x17; 0≤m≤0x3B)
US U <1F><55> Display Time Continuously
ESC G d1 ~ d
<1B><47><d1>~<d
1920
ESC t n <1B><74><n> Select Code Page (n=0,1)
HT <09>
ESC [C <1B><5B><43>
BS <08>
ESC [ D <1B><5B><44>
US LF <1F><0A>
ESC [ A <1B><5B><41>
LF <0A>
ESC [ B <1B><5B><42>
HOM <0B>
ESC [ H <1B><5B><48>
US CR <1F><0D>
ESC [ R <1B><5B><52>
CR <0D>
ESC [ L <1B><5B><4C>
US B <1F><42>
ESC [ K <1B><5B><4B>
US S x y <1F><24><x><y>
ESC I x y <1B><6C><x><y>
Specify Overwrite Mode
Specify Vertical Scroll Mode
> Bit Image Display
1920
Move Cursor Right
Move Cursor Left
Move Cursor Up
Move Cursor Down
Move Cursor to Home Position
Move Cursor to Right-Most
Move Cursor to Left-Most
Move Cursor to Bottom
Move Cursor to Specified Position
(0≤x≤0x1D; 0≤y≤3)
Part 5
T31454
SPECIFICATION
OPTICAL
Number of digits 30 digits/row, 4 rows
Dot matrix 8 x 16 dots
Digit height 8.47 mm
Digit width 4.24 mm
Display color White
Background color Blue
MECHANICAL
Total Height 431 mm (PD-76X0)
200 mm (PD-76X4)
Total Width 221 mm.4
Total Depth 110 mm.4base39.06
Display Window Width 130 mm
Display Window Height 37 mm
Case color Black or Ivory (PD-76X0)
Black (PD-76X4)
ELECTRICAL
Power from adaptor: 12 V AC 1.5A
RS-232 communication protocol: 9600 bps, none parity, 8 data
ENVIRONMENTAL
Operating temperature 0° to + 50°C
Storage temperature -10° to + 60°C
Operating humidity 20% to 85%, non-condensing
Storage humidity 5% to 90%, non-condensing
WARNING: If the user opens the pole display housing to make any
modification, all the product warranty will be voided.
NOTE: Please refer to Posiflex Product Information DVD or visit
our web http://www/posiflex.com.tw for further information when
needed.
bits, 1 stop bit
警告使用者
警告使用者
警告使用者警告使用者
這是甲 類的資 訊產 品，在 居住 的環
境中 使 用 時 ， 可 能會 造 成 射 頻干
擾，在 這種情 況下 ，使用 者會 被要
求採取某些適當的對策。
Part 6
Loading...