Posiflex PD-2605UE User Manual

P/N:

194309030

20

PD – 309 / 2605 Series

FCC Notes:

This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions manual, may cause interference to radio
communications. It has been tested an found to comply with limits for a Class A digital
device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide
reasonable protection against interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which
case the user at his own expense will be required to take whatever measures to correct
the interference.

Warranty Limits:

Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims
any warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
http://www.posiflex.com or http://www.posiflex.com.tw
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technology, Inc. the publisher of this documentation.
© Copyright Posiflex Technology, Inc. 2010
All brand and product names and trademarks are the property of their respective holders.

User’s Manual

Rev. A0

Part 1

BRIEF INTRODUCTION

THE PRODUCT

The PD-309/ PD-2605 is a pole mount customer display option designed for
Posiflex mini slim base of KS-2010A, KS-6810, DT-20X and Gen.6 & 4.5
base of KS series POS terminals. It is delivered in separate carton for the host
system and shall be installed per instructions in this manual.

FEATURES

• LCD (Liquid crystal display) with dark blue character and yellow
green back-light for PD-309

• Bright VFD (vacuum fluorescent display) with green filter for PD­2605

• Two-line display with 20 characters per line

• Easy viewing characters (6.0 mm by 9.66 mm for PD-309 / 9.03

mm by 5.25 mm for PD-2605)

• Long life and trouble free operation

• 15°, 30° and 45° adjustable viewing angles

• Display frame can rotate horizontally 270° freely

• Selectable command emulation modes including PST and EPSON

command emulation modes for PD-309

• Various command emulation modes selectable by DIP switch for
PD-2605

• Support 13 Code Pages of 128 characters each for PD-2605

• Support 12 international character sets of 12 characters each for

PD-2605

• Simple installation

• Selectable between Serial (RS232) interface models: PD-

309S/2605S and USB interface models: PD-309U/2605U.

• Supports UPOS 1.8 and is WEPOS ready for PD-2605

Part 2

Pix. 2

Pix. 1

INSTALLATION GUIDES

HOST SYSTEM PREPARAION

For serial interface (RS232) PD-309 or PD-2605 to be used in KS-2010A, KS­6810, DT-20X and Gen.6 & 4.5 base of KS series, you have to adjust during
power off the internal jumper of the host system to supply 5 V DC to the
COM port selected for the serial interface pole display. This adjustment has to
be done by a qualified electronic technician following guide from relevant
technical manual. The default communication protocol should be set to 9600
bps, none parity, 8 data bits, 1 stop bit with hardware handshaking on CTS.
The power for the USB interface type pole display is supported through the
USB connection. However, should these customer displays are to be connected
through an USB HUB instead of a direct USB port of the system, the HUB
must be powered by a separate power adaptor otherwise there could be the
power shortage problem.

INSTALLATION

The PD-309 or PD-2605 can be
attached to the corner in bottom
plate of the KS-2010A, KS­6810, with slim base, DT-20X
and Gen.6 & 4.5 base of KS
series. It takes examples of this
LCD customer display to fix in
the KS-2010A, KS-6810, and
DT-20X. Refer to the pictures
in Pix.1 at right. Use the 3 attached screws to fix the metal
base plate of the PD to bottom of mini slim base or DT­20X at the circled positions. For mini slim base Connect
the interface cable to go into the base through cable exit
arrowed in Pix.2 at right to the main unit. For DT-20X
arrange the interface cable to go through under bottom to
connector area arrowed in Pix.1 at above right.

CAUTION: There are self-tapping screws for PD-309/ PD-2605 when use
in Gen.4.5 base stand and please aim to the holes which marked “DT” as
showing in the upper picture Pix.1. Other Bing Head Screws are use when
fix in KS-2010A, KS-6810, DT-20X and Gen.6 base stand of KS series.

Base for KS-2010

Bottom of DT-20X

Part 3

Pix. 3

COMMAND EMULATION MODE SETUP

DIP switch
window

Now please check the back of PD-2605 display head as in the above left
picture in Pix. 3. There is a small piece of plastic cover for the “DIP switch
window”. Slide the cover downward but don’t pull it off otherwise you may
have to practice for inserting it back. You can find 6 positions of DIP
switches in this window. Adjust for the appropriate command mode used by
the application program according to below table. Switch position counts
from left to right and “ON” means pushed up as indicated in the above right
part in Pix. 3.

Switch Position

1 2 3 4 5 6

ON OFF OFF ON OFF OFF
ON OFF ON ON OFF OFF
ON OFF ON OFF OFF OFF
ON OFF OFF ON ON OFF
ON OFF ON OFF ON OFF

ON OFF ON ON ON OFF
The factory default command mode is set to Noritake mode for normal
delivery. Please change it to Epson mode if OPOS or UPOS driver is used for
the application program.

(FOR PD-2605)

Command Mode

ADM
Aedex
Epson

Futaba

Noritake

UTC

POWER ON SIGN

With interface cable connection well installed (and with COM port power set
for serial models), turn on the Posiflex POS system, a firmware identifier as
power on sign will appear on the pole display screen for a while to indicate
that pole display is self-tested O.K. and ready to work.

USING THE CUSTOMER DISPLAY

INTERRFACE SELECTION

This series of customer display is designed to serve in Posiflex POS systems
with RS232 interface models and with USB interface models. It is advisable to
well study the I/O port availability of the host system before determining
which interface model to be used.

Part 4