Posiflex MR-2106 User Manual
T31454
MR-2100/2200 SERIES
MAGNETIC STRIPE READER
USER’S MANUAL
Rev. : Original
I. FEATURES
Dual directional operation.
Convenient operation dual side swipe design (MR-2200).
Built-in Magnetic Stripe Reader Triple tracks.
Built-in keyboard wedge interface or RS-232 interface or USB interface.
Built-in decoder
Heavy duty die cast case
3 tracks type MSR can read also AAMVA and CA DMV card
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual,
may cause interference to radio co mmunications. It has been tested and found to comply with limits for a C lass A digital device pursuant to subpart J o f Part
15 o f FCC Rules, which are designed t o provide reasonable protection against interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case t he user at his own expense will be required to t ake whatever measures t o correct
the interference.
WARRANTY LIMITS
Warranty will ter minate automatically when t he equipment is opened by any person other t han the authorized technicians. The user should co nsult
his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of t his merchandise. The manufacturer is by
no means responsible for any damage or hazard caused by improper application.
The hardware utility program, including instructions for its use, is provided “AS IS” without warranty of any kind. Po siflex Technology, Inc. further
disclaims all implied warranties including without limitation any implied warranties of merchantability or of fitness for a particular purpose. The entire risk
arising out of the use or performance of the software and documentation remains with you.
ABOUT THIS MANUAL
This manual is written in an attempt with full strength to assist t he user to utilize the st and-alone magnetic stripe reader MR2100/MR2200 series of
Posiflex POS products. This series of products provide excellent flexibility and reliability in application. This manual covers both operational and technical
aspects of these units.
The manufacturer o f t he MR2100/2200 series heartily apologizes to the user for reserving the right to change o r to modify this manual without
notice due to the rapid and constant pro gress and improvement on science and technology. The user may always obtain the most up to date information
through any of our web sites: http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com.
All rights are strictly reserved. No part of this documentation may be r eproduced, stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of Posiflex Technology, Inc. the publisher of this documentation
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technology, Inc. an ISO-9001 and ISO-14001 certified manufacturer.
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
II. MODEL IDENTIFICATIONS
Models
Application
Interface USB or RS232 or PS2 USB or RS232 USB or RS232 or PS2
Reader Head ISO Single Head JIS2 ISO Dual Side Head
Copyright Posiflex Technology, Inc. 2011
P/N: 19030901010
MR2100 MR2100-JIS2
警告使用者
警告使用者
警告使用者警告使用者
這是甲 類的資 訊產品 ，在 居住的 環
境中 使 用 時 ， 可能 會 造 成 射 頻干
擾，在 這種情 況下， 使用 者會被 要
求採取某些適當的對策。
MR2200
III. SPECIFICATIONS
Reader specification
Applicable card type
Card feed method
Card feed direction
Read / write function
Card feed speed 5 to 55 inches/sec. 100 ~ 1200 mm/sec.
Error rate Less than 0.5% Less than 0.1%
Card data format
Data standard IATA ABA THRIFT
Track used Track 1 Track 2 Track 3 (Track 2) Rear side
Applicable to
models
Recording method
Recording density 210 BPI 75 BPI 210 BPI 75 BPI 210 BPI
Recording capacity
characters / bits
Note: AAMVA and CA DMV standards are supported in 3 track ISO models
Dimensions: 14.5 cm (L) X 4.6 cm (W) X 3.4 cm (H)
Weight: 490 gm
LED: dual color -- green for good read or ready to read
red for invalid read
Rated voltage: 5 VDC
Rated current: 100 mA max.
ISO 7811 JIS X 6302
Manual
Bi-direction
Read only
MR2100-MR2200 MR2100-JIS2
F2F (FM)
79 / 7 40 / 5 107 / 5
JIS I JIS II
40 / 5 72 / 7
Page 1 / 2
KB I/P
PC USB port or USB hub
MR2100
/MR2200
D sub 9 P Female
IV. CABLE CONNECTION GUIDE
Cable connection for KB WEDGE models
PC
Mini DIN 6 P Male
MR2100/MR2200
Mini DIN 6 P Female
PC
Keyboard
Cable connection for RS232 interface models
MR2100/MR2200
2.5/5.5 DC plug from power adaptor
to COM port
Cable connection for USB interface models
V. ADJUSTABLE PARAMETERS
Some parameters in readout format of the MR2100/MR2200 series in PS/2 KB interface and USB
interface can be controlled by software downloaded from our web site: http://www.posiflex.com.
However, PS/2 and USB model are automatically saved parameters even after power off and on. It is also
possible to adjust some parameters with modification in hardware described below if not by software.
Please note that the individual track enable mentioned applies only when the track is supported in
physical reader head.
For ISO & JIS2 in USB Mode Jumper Setting
(1). P2 : Connected to USB Cable
(2). CN3 : ISP(Update MCU Firmware)
(3). CN4 / CN5 : ISO Magnetic Stripe Reader
(Use in "USB KB mode" or HID mode")
(4). CN4 / CN5 : JIS2 Magnetic Stripe Reader
(Only use in "USB KB mode")
Jumper Setting:
Jumper
Position
Function ALT-Num NumLock USB Class Boot protocol
Opened Enable
Closed Disable N/A HID Class for Windows
Default Close Close Close Close
J1 J2 J3 J4
Send Numlock Key
Code
Vendor Class for Linux
or WinCE
Boot protocol for DOS
6.22
Non-Boot protocol for
Windows
For ISO in PS2 & RS232 Mode Jumper Setting
For RS232 Mode:
(1). P1 : Not connected.
(2). P2 : Cable Connected to MB(Com Port) &
Power: 5V.
(3). CN3 : ISP(Update MCU Firmware)
(4). CN4/CN5: ISO Magnetic Stripe Reader/JIS2
Jumper Setting:
Jumper J1 J2 J3 J4 J5 J6 JP1 JP2
Function Alt-Num Lead/
End Code
Opened Enable Enable PS2 Disable Disable Disable
Closed Disable Disable RS232 Enable Enable Enable
Default
PS2/
RS232
CLOSE
Trk1 Trk2 Trk3 Header2x2
RS232
CLOSE OPEN
Header2x2
PS2
Note: RS232 Mode must be closed J3, JP1; Opened JP2.
For PS2 Mode:
(1). P1 : Connected to PC(PS2-KB Port)
(2). P2 : Connected to Keyboard
(3). CN3: ISP (Update MCU Firmware)
(4). CN4/CN5: ISO Magnetic Stripe Reader
Jumper Setting:
Jumper J1 J2 J3 J4 J5 J6 JP1 JP2
Function Alt-Num Lead/
End Code
Opened Enable Enable PS2
Closed Disable Disable RS232
Default
PS2/
RS232
OPEN
Reserve Reserve PS2 Pin
Switch
OPEN
Header2x2
RS232
OPEN CLOSE
Header2x2
PS2
Note: PS2 Mode must be opened J3, J6, JP1; closed JP2
Page 2 / 2
Loading...