POSIFLEX LM6100 User's Manual

LM6100 Series

LCD Monitor

USER’S MANUAL

Rev. : A

I. FEATURES

• Light weight and high luminance LCD monitor for industrial and commercial use

• Application covers POS, POIS (Kiosk), Factory Automation etc.

• High quality 12.1” TFT LCD panel with scaling up function for full screen display

• Successor from earlier LM6000 series and supports display resolution up to 1024 x

768 pixels

• Tilt and swivel adjustable construction

• Spill proof and easy maintenance structure allowing easy cleaning

FCC NOTICE

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to
comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to
take whatever measures to correct the interference.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any person other than the authorized
technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow
the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.

ABOUT THIS MANUAL

This manual assists the user to utilize the LCD Monitor LM6100 series. These series provide versatile font
formats and support various instruction sets. These series of products receive instructions in serial communication
protocols and is capable of entering pass through mode so that all instructions received pass on to next connected serial
device if properly configured.

The manufacturer of the LM6100 series heartily apologizes to the user for reserving the right to change or to
modify this manual without notice due to the rapid and constant progress and improvement on science and technology.
The user may always obtain the most up to date information through any of our web sites: http://www.posiflex.com.tw,
http: //www.posiflexuk.com, http://www.posiflexusa.com.

TRADE MARKS AND SERVICE MARKS

POSIFLEX is a registered trademark of Mustek Corp..
Other brand and product names are trademarks and registered trademarks and service marks of their respective

owners.

 Copyright Mustek Corp. 2002, 2003

P/N: 19050900020 1

on back of

II. MODEL NUMBERS

LM6112: 12.1” LCD Monitor w/ stand

LM6101: 12.1” LCD Monitor w/ joining mechanism for Posiflex touch

terminals such as TP-7000 series

LM6101

TP7000

LM6112

III. CARTON CONTENTS

1. LCD Monitor panel unit

2. Monitor stand (for LM6112) or joining mechanism (for LM6101)

3. Pivot screw (1x) and pan head fixing screws (2x for LM6101)

4. User’s Manual

5. VGA cable: 20867244100 (for LM6112) or 20863241710 (for
LM6101)

6. Power adaptor: ASP0P042WTB001 & power cord (for LM6112)

IV. INSTALLATION

1. Match the bottom of the panel unit into the monitor stand (for LM6112) or
joining mechanism (for LM6101).

2. Screw on the pivot screw for LM6112. Screw on the pivot screw through a
split washer and then through a plain washer for LM6101.

3. Fix LM6101 to the Posiflex TP7000 terminal per instruction of the terminal.

4. For LM6112, connect the end of VGA cable with the power connector to the

2

LM6112 LM6101

Pivot Screw

VGA Connector

Power Connector in VGA Cable

Power Connector from Power Adaptor

for LM6112

back of the panel unit. For LM6101, please arrange the power to be supplied
through the interface cable from the main unit and just connect the video
interface cable. Connect the other end of VGA cable to the appropriate VGA
port. The monitor will always turn ON whenever power is made available.

5. Adjust for best viewing tilt angle and engage the on screen display (OSD)
adjustment for best display effect whenever necessary. The monitor will sign
for “No Signal” status and go into power saving mode in 5 seconds when
there is no video signal. The display will come back when the signal does.

V. OSD

A. OSD buttons

“OSD” button: To enter OSD setup menu, or to perform funct ion selected

in OSD operation.

“NXT” button: To go to next option function.
“” “” button: To increase setting.
“” “” button: To decrease setting.
“” “” button: To turn the monitor power ON/OFF. The monitor can be

turned OFF only when there is video signal and can be turned ON only
when there is video signal and after the “Turn Off Panel” message

3