Posiflex LM-2208 User Manual

P

/N:

196809010

2

0

LM-2208, LM/TM-2212

LCD Monitor

User’s Manual

FCC NOTICE

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause interference to radio communications. It has been tested and
found to comply with limits for a Class A digital device pursuant to s ubpart J of Part 15 of FCC Rules, which are
designed to provide reasonable protection against interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which case the user at his own
expense will be required to take whatever measures to correct the interference.

WARRANTY LIMITS

Warranty will ter minate automatically when the machine is opened by any person other than the authorized
technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not
follow the instructions in application of this merchandise. The manufacturer is by no means responsible for any
damage or hazard caused by improper application.

ABOUT THIS MANUAL

This manual assists the user to utilize the LCD Monitor LM-2208/LM-2212/TM-2212. These series provide
adjustable robust construction for 8” LCD display with maximum resolution of 800 x 600 and 12” LCD display
with maximum resolution of 1024 x 768.

The manufacturer of the LM-2208/LM-2212/TM-2212 series heartily apologizes to the user for reserving the
right to change or to modify this manual without notice due to the rapid and constant progress and improvement
on science and technology. The user may always obtain the most up to date information through any of our web
sites: http://www.posiflex.com, http://www.posiflex.com.tw, http://www.posiflexusa.com.

 Copyright Posiflex Technology, Inc. 2009

TRADE MARKS AND SERVICE MARKS

POSIFLEX is a registered trademark of Posiflex Technology, Inc.

Other brand and product names are trademarks and registered trademarks and service marks of their
respective owners.

Rev. A0

I. FEATURES

• The LM-2208/LM-2212/TM-2212 particularly designed for Posiflex XP

series POS terminals

• Most stable 8” or 12” LCD monitor with tilt adjust for industrial and

commercial use

• Optional side mount devices (SD300) for TM-2212 Only.

• High quality TFT LCD panel

• Easy maintenance structure allowing easy cleaning

• Super VGA monitor resolution up to 800 x 600 pixels for LM-2208 and

1024 x 768 pixels for LM/TM-2212.

• Resistive type extra long life touch panel in USB interface (for TM-2212)

Page 1

“

OSD

”

LM/TM

-

2212 LM -2208

• Touch functions include left/right button, double click, drag & drop (for

TM-2212)

• Support power supply through LCD cable from Posiflex XP-2000 series

POS systems to operate without power adaptor

II. MODEL NUMBERS

LM-2208: 8” 800 x 600 LCD Monitor
LM-2212: 12” 1024 x 768 LCD Monitor
TM-2212: 12” 1024 x 768 LCD Touch Monitor

III. CARTON CONTENTS

1. 8” or 12” LCD Monitor (Main unit assembled with Bracket)

2. User’s Manual

3. LCD Cable particular designed for LM-2208/LM-2212/TM-2212

IV. PARTS IDENTIFICATION

LM-2208 LM/TM-2212

Main Unit

Display Screen

Power LED

Bracket

LED INDICATION STATUS

• Standby (no signal): Orange for LM-2208 or

Green for LM/TM-2212

• Operating: Blue

Control Buttons and Power switch

“NXT” - OSD Menu/Submenu Next Button

“EXT” - OSD Menu/Submenu Exit Button

- OSD Menu/Submenu
Engage Button

“+” - Up/Increase Select/Setting Button

“-” - Down/Decrease Select/Set Button

Power Switch

SD-300

Page 2

A C

V

GA

U

SB

V. HARDWARE INSTALLATION

A. 2nd LCD Monitor

Please refer to following installation and join the 2nd LCD monitor to XP­2000 series step by step.

1. Cable Exit Cover

Please release the cable exit cover as following steps:

A: Please find the back of cable cover which just near the I/O plate.
B: Please use the Fingertip to release compression lock.
C: after the cable cover released, please cut the circle part which show in the

picture C.

B

After finish this step, the cable cover can be use when the rear mount upgrade
kits fixed.

2. Mount the bracket to XP-2000 series’ back cover

Please aim to the three screws holes of bracket to the
terminal’s back cover’s screws holes as show on the
picture. Then fasten the screws which come with
LM-2208/LM-2212/TM-2212. After fix the LM­2208/LM-2212/TM-2212 to the XP-2000 series,
please use the cable exit to pass through the VGA
cable to the terminal’s I/O plate.

Next, please use the VGA Cable to connect to the LM-2208/LM-2212/TM­2212 and XP-2000 series’ VGA ports as well as use the attached USB cable to
connect TM-2212 and XP-2000 series’ USB Port. After these steps, the
installation process of LM-2208/LM-2212/TM-2212 is finished. For power
supply of VGA ports in XP-2000 series, please contact to local dealer of
authorized technicians.

TM-2212

Page 3