Part 1
I. FEATURES
• Light weight and high luminance LCD monitor for industrial and
commercial use
• Application covers POS, POIS (Kiosk), factory Automation etc.
• High quality 10.4” TFT LCD panel with scaling up function for full screen
display
• Supports display resolution up to 800 x 600 pixels
• Tilt adjustable construction
• Spill proof and easy maintenance structure allowing easy cleaning
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with limits for a Class A digital device
pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection
against interference when operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his own expense will be
required to take whatever measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other
than the authorized technicians. The user should consult his/her dealer for the problem happened.
Warranty voids if the user does not follow the instructions in application of this merchandise. The
manufacturer is by no means responsible for any damage or hazard caused by improper application.
ABOUT THIS MANUAL
This manual assists the user to utilize the LCD Monitor LM-2010/2010A/2110/2110A
series. This series is a 10.4” LCD monitor of long endurance industrial standards. The LM2010/2010A is a upgrade kit particularly designed for Posiflex hybrid terminal HT series host
system.
The manufacturer of the LM-2010/2010A/2110/2110A series heartily apologizes to the
user for reserving the right to change or to modify this manual without notice due to the rapid and
constant progress and improvement on science and technology. The user may always obtain the
most up to date information through any of our web sites: http://www.posiflex.com.tw, http:
//www.posiflex.com, http://www.posiflexusa.com.
Copyright Posiflex Technologies, Inc. 2009
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technologies, Inc..
Other brand and product names are trademarks and registered trademarks and service marks
of their respective owners.
P/N: 19670900030
LM-2010 / 2010A / 2110 / 2110A
LCD Monitor
User’s Manual
Rev. B0
Downloaded from ManualMonitor.com Manuals
Part 2
II. MODEL NUMBERS
LM-2110 / 2110A: 10.4” LCD Monitor w/ stand
LM-2010 / 2010A: 10.4” LCD Monitor w/ support bracket for Posiflex
hybrid terminals HT series
III. CARTON CONTENTS
1. LCD Monitor panel unit
2. Base stand (for LM-2110 / 2110A) or support bracket (for LM-2010 /
2010A)
3. Fixing screws (2x for LM-2010 / 2010A, 6x for LM-2110 / 2110A)
4. User’s Manual
5. VGA cable: 21867244100 (for LM-2110 / 2110A) or 21863241730 (for
LM-2010 / LM-2010A)
6. Power adaptor: ASP0P042WTB001 (for LM-2110) or 21972018120
(for LM-2110A) & power cord (for LM-2110)
IV. INSTALLATION
1. Use 2 fixing screws to fit the monitor stand
(for LM-2110 / 2110A) or support bracket
(for LM-2010 / 2010A) to the back of the
LCD panel as arrowed in the right picture.
Connect the VGA cable to the connector at
back of the LCD panel and screw in its fix
screws as circled in the same picture.
2. For LM-2110 / 2110A, connect the
power connector at panel back end
of VGA cable to the power
connector as in left picture. Connect
and screw-fix the other end of VGA
cable to the appropriate VGA port of
host system. Please check that the
city power supply specification from
the wall socket is within the
operation range of the power adaptor. Insert the power adaptor to the
wall socket and the LM-2110 / 2110A is ready for work.
3. For LM-2010 / 2010A, following actions shall be taken to install it onto
HT systems with power for HT systems disconnected and also
reference of the manuals of the HT systems.
On base unit of HT systems, there must be 4 screw hole covers on top
side of its plastic top cover and the VGA cable hole cover within the
Power Connector from
Power Adaptor
Power Connector in VGA
Cable for LM-2110 / 2110A
Downloaded from ManualMonitor.com Manuals
Part 3
pole cover of its back cable cover as in picture below. There are 2
bridges from each screw hole cover to the HT top cover and 3 bridges
from the VGA cable hole cover to the pole cover as enlarged in the
accompanying drawings.
Use proper tool to cut the bridges off with the screw hole cover and
VGA cable hole cover from the top cover and pole cover at points
indicated by each pair of arrows in the drawings. Sand/Cut smooth the
inside of the holes resulted.
In the HT system, please arrange the VGA power to be supplied
through the interface cable from the main unit through internal jumper
setting change with reference to its technical information by a qualified
technician.
Connect and screw the video interface
cable to the VGA port. The monitor
will always turn ON whenever power
is made available from the HT system.
Use 4 fixing screws to fit the bottom of
LM-2010 / 2010A supporting bracket
to HT system base top as arrowed in
the right picture and have the VGA
cable pass through the VGA cable hole
as circled in the same picture.
Please note that for LM-2010 / 2010A with a 2-digit system revision
number, the screw holes on support bracket base look like the below
left picture and the LM-2010 / 2010A can be fixed to straight backward
of the HT or PB system.
For LM-2010 / 2010A with
3-digit system revision
number (3rd digit being “a”)
or later, the bracket base is
like the right picture and
the LM-2010 / 2010A can
HT Cable Cover Pole Cover
Screw Hole
Screw Hole Cover VGA Cable Hole Cover
Bridge
Bridge
Downloaded from ManualMonitor.com Manuals
Loading...