Posiflex JIVA KS-7717 User Manual
P/N:
1648090003
0
KS – 7715/7717/7515/7517
Fan Free Touch Terminal
KS-7715/7717 KS-7515/7517
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex Technology, Inc. will assume no liability for any technical inaccuracies or
editorial or other errors or omissions contained herein, nor for direct, indirect,
incidental, consequential or otherwise damages, including without limitation loss of
data or profits, resulting from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims
any warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex Technology, Inc. reserves the
right to alter product designs, layouts or drivers without notification. The system
integrator shall provide applicative notices and arrangement for special options utilizing
this product. The user may find the most up to date information of the hardware from:
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technology, Inc. the publisher of this documentation.
© Copyright Posiflex Technology, Inc. 2012
All brand and product names and trademarks are the property of their respective holders.
User’s Manual
Rev.: B0
Part 1
ALERT TO OUR HONORABLE CUSTOMERS:
Please always read thoroughly all the instructions and documents
delivered with the product before you do anything about it. Don’t
take any premature action before you have a full understanding of
the consequences.
This product contains inside a Lithium battery. Please always
follow local environmental protection laws / regulations for disposal
of used batteries and always replace only with battery of same type.
If you have an UPS battery installed in the product:
Temperature above 40°C must be strictly avoided as it
could cause termination of battery life and unexpected result
even if the battery is not in work.
Do not power off the system just by shutting off the AC
power leaving the battery supporting the whole system till
completely exhausted. Repeatedly using it up or improper
maintenance reduces the battery life dramatically.
Always fully recharge the UPS battery at least once every 3
months if the battery is not connected.
Always disconnect the UPS battery from the system if the
system is to be left OFF for more than 72 hours to prevent
possible damage. Only connect the UPS battery back right
before you are going to re-power on the system.
Replace the UPS battery as soon as the monitoring software
indicates the battery is out of service. Attempt to recharge a
dead battery is dangerous!
A separate battery monitor is not required for this series.
DAILY MAINTENANCE GUIDE
For regular cleaning of the KS systems, please use only soft haired brush or
dry soft cloth. You may use moist soft cloth to remove stains when necessary.
Apply only proper amount of mild neutral detergent for obstinate stains. Please
note that never use Acryl dissolving solvent or Polycarbonate dissolving
solvent. You may apply ammonia-based glass cleaner only on the screen
surface.
Risk of Explosion If Battery Is Replaced By An Incorrect Type
Dispose Of Used Batteries According To Local Regulations
CAUTION
Part 2
KS-7
515
/7517
Front
KS-7515
/7517
Rear
Left
KS-7715
/7
717 Front
KS-7715
/7717
Rear
KS-7715/
7717/
7515
/7517
Power
INTRODUCTION
Main Unit
1
2
3
4
5
1
2
3
6
6
4
5
7
8
9
10
Part 3
8
PARTS IDENTIFICATION
1. Main Unit
2. Touch panel / LCD panel
3. Side Mount Bay
4. Power indicator
5. Base stand (Gen6 or Gen 5.5, specified on order)
6. HDD cover
7. Power switch
8. Brightness adjust push button “+”
9. Brightness adjust push button “-”
10. +12V Powered USB port
Base Stand
Gen 6
1
2
4
3
6
6
10
5
11
12
Gen 5.5
5
7
8
9
10
7
9
Part 4
PARTS IDENTIFICATION
1. Lock/Release button for main unit
2. Tilt adjustment
3. Base stand
4. Cable exit
5. Cable groove
6. Cable exit
7. Cable holder
8. Bottom plate
9. Cable passage in bottom plate
10. Rubber feet with bottom plate fixing screw
11. Rubber feet with bottom plate fixing screw
12. UPS battery bracket
PRODUCT FEATURES
Standard Features:
a)
a)
Mainboard: the compatible mainboard shared between KS-7715 and
a)a)
KS-7515
b)
b)
CPU: KS-7715/7717 -i5-2510E 2.5GHz, 3M Cache
b)b)
KS-7515/7517 - Intel Celeron B810
- Intel Celeron B815
- Intel Pentium B950
c)
c)
Fan free structure with Aluminum die-cast main unit casing for harsh
c)c)
environment.
d)
d)
Data storage device: 2.5” SATA HDD in main unit or optional SSD in
d)d)
main unit or optional SATA HDD in base with optional RAID 1 control
e)
e)
An advanced slim base design that supports 2
e)e)
mount customer display on rear base, storage room for optional 2.5”
HDD and optional UPS battery in base. Also possible to be without
base but wall mount bracket for wall mount application.
f)
f)
OS Support: XP Pro, POS Ready 2009, Win 7, POS Ready 7, Linux
f)f)
g)
g)
High quality 15” TFT (KS-7715/7515) 17”TFT (KS-7717/7517) active
g)g)
matrix LCD panel
h)
h)
LCD panel with easy tilt angle adjustment from 15° to 70°
h)h)
i)
i)
LCD brightness adjust buttons at side of main unit
i)i)
j)
j)
Power Supply: KS-7715-7717/120W;KS-7515-7517/80W
j)j)
k)
k)
Touch screen: 5-wire resistance, IR, or Projective Capacitive
k)k)
l)
l)
Water resistant structure allowing easy cleaning
l)l)
m)
m)
Easy maintenance construction
m)m)
nd
LCD display or pole
Part 5
n)
n)
RAID-support for KS-7715/7717/non-RAID support for KS-7515/7517
n)n)
o)
o)
Various I/O ports supported, including:
o)o)
1. 4 serial ports with 3 of DB9 connectors and one 10-pin RJ45 type
modular connector. The COM1/2/3/4 connectors are supported with
capability for +5V DC support through BIOS setup and Jumper
setting.
2. +12V DC power supply for COM 1/2/3/4 through jumper setting.
3. 6 standard USB ports on the rear I/O panel, another standard USB
port on the other side
4. One LAN port Ethernet 10/100/1000 Base T with LAN status
indicators on jack (green for link, orange for data transmission)
5. One external VGA monitor port with +12V DC support through
BIOS setup
6. LED indicators for systems operation status
7. Two built-in internal 2W speaker with one line-out
8. One CR port capable of controlling up to 2 cash drawers.
9. One 4-pin connector for optional UPS battery in base
p)
p)
Touch control functions: left/right button, double click, drag & draw
p)p)
q)
q)
Dual display support (per OS capability)
q)q)
r)
r)
VGA memory support DVMT 5.0.
r)r)
s)
s)
Supports SO-DIMM socket X 2, DDR3 1066/1333 MHz, Max up to
s)s)
8GB
t)
t)
Integrated structure for side mount upgrade kit like SD-460W/SD-
t)t)
660W/SD-860W/KP-300W with software programmable MSR
u)
u)
Preconditioned power up function set up thru BIOS –Wake System
u)u)
with Fixed Time/Wake Systems with Dynamic Time, Wake on LAN,
and Wake on Ring
Option Items:
Note: The underlined items in the following list means that option must be
set prior to shipment from the factory. The rest items can be set by the
dealers.
a) DDR3 SODIMM memory expansions up to 4GB max in one SODIMM,
TTL 8GB
b) 16~128GB SSD
c) RAID 1 control for both SATA HDD’s in main unit and in base for
KS7715-7717 only
d) Integrated side mount upgrade kit:
SD-460W/SD-660W/SD-860W: with options
MSR, optical fingerprint sensor, RFID or Wi-Fi.
KP300W: Programmable keypad with options MSR, smart card
reader
Part 6
Loading...