Posiflex JIVA KS-7215 User Manual
P/N:
164409030
30
KS – 6915/6917/7215/7217
Fan Free Touch Terminal
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex Technology, Inc. will assume no liability for any technical inaccuracies or
editorial or other errors or omissions contained herein, nor for direct, indirect,
incidental, consequential or otherwise damages, including without limitation loss of
data or profits, resulting from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims
any warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex Technology, Inc. reserves the
right to alter product designs, layouts or drivers without notification. The system
integrator shall provide applicative notices and arrangement for special options utilizing
this product. The user may find the most up to date information of the hardware from:
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technology, Inc. the publisher of this documentation.
© Copyright Posiflex Technology, Inc. 2012
All brand and product names and trademarks are the property of their respective holders.
User’s Manual
Rev.: B0
Part 1
ALERT TO OUR HONORABLE CUSTOMERS:
Please always read thoroughly all the instructions and documents
delivered with the product before you do anything about it. Don’t
take any premature action before you have a full understanding of
the consequences.
This product contains inside a Lithium battery. Please always
follow local environmental protection laws / regulations for disposal
of used batteries and always replace only with battery of same type.
If you have an UPS battery installed in the product:
Temperature above 40°C must be strictly avoided as it
could cause termination of battery life and unexpected result
even if the battery is not in work.
Do not power off the system just by shutting off the AC
power leaving the battery supporting the whole system till
completely exhausted. Repeatedly using it up or improper
maintenance reduces the battery life dramatically.
Always fully recharge the UPS battery at least once every 3
months if the battery is not connected.
Always disconnect the UPS battery from the system if the
system is to be left OFF for more than 72 hours to prevent
possible damage. Only connect the UPS battery back right
before you are going to re-power on the system.
Replace the UPS battery as soon as the monitoring software
indicates the battery is out of service. Attempt to recharge a
dead battery is dangerous!
A separate battery monitor is not required for this series.
DAILY MAINTENANCE GUIDE
For regular cleaning of the KS systems, please use only soft haired brush or
dry soft cloth. You may use moist soft cloth to remove stains when necessary.
Apply only proper amount of mild neutral detergent for obstinate stains. Please
note that never use Acryl dissolving solvent or Polycarbonate dissolving
solvent. You may apply ammonia-based glass cleaner only on the screen
surface.
Risk of Explosion If Battery Is Replaced By An Incorrect Type
Dispose Of Used Batteries According To Local Regulations
CAUTION
Part 2
INSTALL GUIDE
After pass through all of connecting cable from the base as instruct in part
10 & 11, please follow the steps to install the terminal and base stand
carefully when first time open the carton.
Since the monitor and stand are packaged separately, please Take Out and
Hold the PE foams Carefully and DO NOT detach and drop it.
After take the PE foam out from the carton,
please remove the PE foam with extra care
and make sure place the terminal and stand
on a soft clean flat surface such as table and
as show in the picture at the right side.
Please find the four holes in the top of stand.
Take the stand and align these four matching
holes to the four matching pegs which are in
the back on terminal.
After matching the stand and terminal, push
the stand to the arrowed direction as show in
the right picture. At this time, turn the
terminal to the normal position and plug the
power then it can start to use.
INTRODUCTION
PRODUCT PICTURES FOR Gen.5 BASE STAND
Front Views Rear Views
Side Views
1
2
5
3
4
6
Part 3
7
8
9
10
Base Stand and Bottom View
Inside touch open door
14
15
11
12
13
16
17
18
19
PARTS IDENTIFICATION
1. Main Unit
2. Touch panel / LCD panel
3. Power indicator
4. Gen 5 base stand
5. Screw holes for optional rear top mount kit such as PD-310 or
PD-2604 or LM-2312 or LM-8035
6. HDD cover
7. Power switch
8. Brightness adjust push button “+”
9. Brightness adjust push button “-”
10. USB ports
11. Base stand
12. Compression lock for base stand cover
13. Cable exit
14. Cable groove
15. Cable exit
16. Cable holder
17. Bottom plate
18. Cable passage in bottom plate
19. Rubber feet with bottom plate fixing screw
Part 4
PRODUCT PICTURES FOR Gen.6 BASE STAND
Front View
2
3
4
Side View
Base Stand and Bottom View
Rear View
1
Inside touch open door
11
12
5
6
7
8
9
10
15
14
13
PARTS IDENTIFICATION
1. Optional Side mount kit
2. Touch panel with Flat screen LCD option
3. Power indicator
4. Gen 6 slim base
5. Screw holes for optional rear top mount kit PD-310 or PD-2604 or
LM-2312 or LM-8035
6. HDD cover
7. Power switch
Part 5
8. Brightness adjust push button “+”
9. Brightness adjust push button “-”
10. USB ports
11. Compression locks for base stand cover
12. Cable groove
13. Cable exit
14. UPS battery bracket
15. Rubber feet with bottom plate fixing screw
PRODUCT FEATURES
Standard Features:
a)
a)
CPU:
a)a)
b)
b)
Fan free structure with Aluminum die-cast main unit casing.
b)b)
c)
c)
Data storage device: 2.5” SATA HDD in main unit or optional SSD in
c)c)
d)
d)
An advanced slim base design that supports 2
d)d)
e)
e)
Support WEPOS, POS Ready, Win7 and Linux environment
e)e)
f)
f)
High quality 15”/17” TFT active matrix LCD panel
f)f)
g)
g)
LCD panel with easy tilt angle adjustment from 15° to 70°
g)g)
h)
h)
LCD brightness adjust buttons at side of main unit
h)h)
i)
i)
Durable resistive type touch panel that endures 10 million touches min.
i)i)
j)
j)
Water resistant structure allowing easy cleaning
j)j)
k)
k)
Easy maintenance construction
k)k)
l)
l)
Various I/O ports supported, including:
l)l)
Intel Pine View D-SC 1.8GHz for KS-6915/6917, Pine View D-
DC D525 Dual Core CPU for KS-7215/7217.
main unit or optional CF card reader adaptor & CF card in main unit or
optional SATA HDD in base with optional RAID 1 control
nd
LCD display or pole
mount customer display on rear base, storage room for optional 2.5”
HDD and optional UPS battery in base. Also possible to be without
base but wall mount bracket for wall mount application.
at same spot (Infra Red type optional)
1. 4 serial ports with 2 of DB9 connectors and 2 of 10 pin RJ45 type
modular connector. The COM1/2/3/4 connectors are supported with
capability for +5V DC support through BIOS setup and Jumper
setting.
2. +12V DC power supply for COM 1/2/3/4 through jumper setting.
3. 7 standard USB ports with 2 at side, 4 in I/O area and 1 internal
proprietary port for extension device.
4. one LAN port Ethernet 10/100/1000 Base T with LAN status
indicators on jack (green for link, orange for data transmission)
5. one external VGA monitor port with +12V DC support through
BIOS setup
Part 6
Loading...