Posiflex HT-4612X User Manual

P/N:

154109000

50

PB-4600

/PB

-

4600E

HT-4600(E/X)

Series

User’s Manual

Rev. D0

FCC Notes:

This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with
limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which
are designed to provide reasonable protection against interference when operated in a
commercial environment. Operation of this equipment in a residential area is likely to
cause interference in which case the user at his own expense will be required to take
whatever measures to correct the interference.

Warranty Limits:

Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims
any warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
http://www.posiflex.com or http://www.posiflex.com.tw
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technology Inc. the publisher of this documentation.
© Copyright Posiflex Technology Inc. 2013
All brand and product names and trademarks are the property of their respective holders.

Page 1

ALERT TO OUR HONORABLE CUSTOMERS:

 Please always read thoroughly all the instructions and documents

delivered with the product before you do anything about it. Don’t
take any premature action before you have a full understanding of
the consequences.

DAILY MAINTENANCE GUIDE

For regular cleaning of the HT-4600(E/X)/PB-4600(E) systems, please use
only soft haired brush or dry soft cloth. You may use moist soft cloth to
remove stains when necessary. Apply only proper amount of mild neutral
detergent for obstinate stains. Please note that never use Acryl dissolving
solvent or Polycarbonate dissolving solvent. You may apply ammonia-based
glass cleaner only on the screen surface.

BRIEF INTRODUCTION

THE USER’S MANUAL

The purpose of this manual is to guide the user in the initial installation and
general use of the Posiflex HT-4600(E/X)/PB-4600(E) series of POS terminals.
It does not explain any application software that may be supplied with it.

We intend to provide our customers with all technology advantages available
by evolving the product design to incorporate appropriate changes and
improvements. So some detail differences may exist between this manual and
the equipment supplied.

For more detailed or technical information please refer to the CD-ROM disc
associated or consult our authorized dealers or visit our web site:
http://www.posiflex.com.tw/ or http://www.posiflex.com/

THE PRODUCT

The Posiflex range of HT-4600(E/X)/PB-4600(E) terminals have been
designed and manufactured to meet the high end demand on POS systems. It
incorporates all the advances of PC technology within a rugged housing
designed for use in a hostile retail environment. By providing an integrated
design, it has retained many of the secure features of a traditional ECR and has
avoided the wiring “spaghetti” associated with more traditional PC solutions.
This Open Standard Architecture ensures that this terminal can use the PC

Page 2

application software and development tools that are now inexpensively
available and abundant.

For the HT-4600(E/X)/PB-4600(E) series terminal is powered by most up to
date CPU and provides a color TFT LCD screen with a resistive type touch
control panel on sturdy and easily adjustable structure on top of the main unit.
HT-4600(E/X)/PB-4600(E) series may be used as a self-content unit or as one
of several terminals in a network system controlled by a “back office”
computer through the integrated network interface. Versatile options besides
the basic model selection can apply to it as well. While PB-4600/E is same as
HT-4600(E / X) but without LCD display.

THE STANDARD FEATURES

 CPU: Intel Pentium 2.0G+
 HDD: 320 GB or above.
 RAM: DIMM socket x 2, DDR-2 667/800MHz, Max 4GB for HT/PB-

4600; SO-DIMM socket x 2, DDR3, Max 8GB for HT-4600(E/X)/PB­4600(E)

 Data storage device: SATA HDD 2.5” or SSD HDD, support 2nd HDD

for HT-4600(E/X)/PB-4600(E)

 Touch control functions for HT-46XX Series: left/right button, double

click, drag & draw

 Ethernet Networking: One LAN port Ethernet 10/100/1000 Base T

with LAN status indicators on jack (green for link, yellow for data
transmission)

 Serial Ports: There are 4 serial ports in a HT-4600(E/X)/PB-4600(E)

system with +5V (through BIOS setting) or +12V (by jumper setting)
power on COM2/3 and it is default as no power at delivery.

 Parallel Port: Each HT-4600(E/X)/PB-4600(E) system is equipped with

a parallel port that supports SPP/EPP/ECP.

 VGA Port: There is a VGA connector for connection of external

monitor with + 12 V DC power supply included. It is default as no
power at delivery.

 USB Ports: The HT-4600(E/X)/PB-4600(E) series is equipped with 6

USB type A connectors for connection of USB (Universal Serial Bus)
devices.

 PS/2 KB Port: 1 PS/2 KB port
 PS/2 Mouse Port: 1 mouse port
 Audio Port: 1 Mic. in / audio line out port
 CR Port: Capable of controlling 2 cash drawers max.
 PCI Slot: 1 PCI extension slot.

Page 3

 Modem Ring-Up, LAN Or Alarm Wake-Up: The HT-4600(E/X)/PB-

4600(E) series can be turned on automatically upon an incoming COM
port Modem call or LAN status or data packet received on LAN or a
preset time/day/week/month.

THE OPTIONAL ITEMS

Note: These items below must be installed by the qualified technician.

Attempt to apply them by end users is either too difficult or is likely to cause
damages. Italic items below are stand alone peripheral devices.

a) Data Storage: SSD kit (It can’t coexist with HDD)
b) Wireless LAN Adaptor(Optional): USB interface, IEEE 802.11b/g
c) Preload OS: Win XP Pro, POSReady2009, POSReady7 or Linux.
d) Support CRT2 through internal interface for PB-4600/E.
e) Optional RAID 1 Function for data security.
f) Two VGA ports for PB-4600/E: One for main Display and another

one for second display.

g) Internal speaker(This must installed prior to delivery from factory)
h) +24V power USB for printer.
i) 150W Power adaptor upgrade for +24V power USB

SYSTEM BOX CONTENTS

When you receive the system box you will find it contains several items:



HT-4600(E/X) system unit with the 12.1” LCD panel integrated on
top or PB-4600/E system unit.



User’s manual.



Recovery DVD for preloaded OS or Posiflex Product Information
DVD for driver utilities without OS.



Optional components installed to system unit as ordered.



Power adaptor and power cord.



PCI Extension slot.

INSTALLATION GUIDES

IMPORTANT

Please do not connect the power adaptor or turn on the main unit until you
have fully read the installation guides and followed the instructions!!!

TECHNICAL ENHANCEMENTS

Applicable technical enhancements in HT-4600(E/X)/PB-4600(E) series

Page 4

include serial COM port power supply settings, VGA port power supply
setting and DRAM upgrades. All these technical enhancement operations
require purchase of applicable Technical Manual from Posiflex or consultation
from Posiflex authorized dealers and should be handled only by a qualified

technician.

MAIN CONNECTION AREA

The HT-4600(E/X)/PB-4600(E) series is constructed for very easy
maintenance. Press inward both plastic buttons at lower rear corners on both
sides of the system unit (circled in right picture) to release the lower part of
back cable cover. Please note that there are 2 plastic hooks on top cover
holding the back cable cover as marked on upper part of the picture. Carefully
release the back cable cover from the hooks to show the main connection area.

Carelessly pressing on these 2 springs could cause damages. The user shall
be responsible for such kind of damage. For the HT-4600(E/X) system even
the maintenance technician must always put a piece of clean flat foam of
sufficient size in front of the system unit before pressing these 2 springs. The
LCD and touch panel may flip forward by gravity and get or cause damage by
hitting anything in front of the
system unit. For the PB-4600(E)
system the maintenance
technician must always pay
attention to always disconnect all
power and cable connections
before pressing the 2 springs and

Push This Button
and also The One
on The Other
Side to Open
Cable Cover

not to cause any damage either in
the top cover opening operation
after pressing the 2 springs or by
leaving or spilling any improper
materials inside after the opening operation.

Note: Please DO NOT press the 2 springs on the metal walls as cross
marked in the picture.

WIRELESS LAN (OPTION)

When the wireless LAN option is ordered with the HT-4600(E/X)/PB-4600(E)
system, this option is already installed in the delivery inside the back cable
cover with its cable connected to one of the USB port. This cable must be
disconnected first if installed whenever the back cable cover is opened for
any operation.

Page 5