POSBank IMPREX PRIME Installation Manual
PBQIG-IMPREX PRIME-E(Rev001;150302)
IMPREX PRIME
OPEN BUTTON
Printer Installation Guide
3. Receipt paper Change
Step 1. Lamp will be turned on when there is no receipt paper
in Internal Printer.
Step 2. Press ‘OPEN’ Button to open printer cover.
Step 3. Put new receipt paper into Internal Printer in the right direction.
Step 4. Take out some inches of paper to outside of device and close
printer cover.
Step 5. Put Monitor back to original state.
2. Self-diagnosis
Step 1. Check receipt paper is set up.
Step 2. Keep pressing FEED Button and turn on POS Terminal.
Self-test will be started.
Step 3. Printer’s firmware version and current setting will be printed.
Step 4. Check current setting and print condition.
Step 5. After finishing Self-diagnosis, Printer will be returned to original
condition automatically.
※Notice
Keep pressing FEED Button and turn on POS Terminal. Wait until Printer finishes printing current
setting and condition. Start other works after printing is totally finished. By Self-diagnosis, you can
check printer is working well. Printing quality, Firmware version, current setting can be checked
by Self-diagnosis.
※Notice
1)Printing speed can be slowed down depending on data transmission speed and
commend combination.
2)The figures were measured at standard temperature and paper. These can be varied depending on
O temperature change or printing level.
3)External surge noise can depress printing quality.
4. Printer Set up
*** Setting Mode ***
‘You can set up Printer’s properties
(communication speed, density, etc.) at ‘Setting Mode’.
[How to enter Setting Mode]
Step 1. Check receipt paper is set up.
Step 2. Keep pressing FEED button and push the Reset button.
Step 3. Self-test will be started.
Step 4. Printer standard setting will be printed.
Step 5. Keep pushing FEED button for 5 seconds. Setting Mode will be started.
Step 6. Configurable properties will be printed as below.
5. Printer specifications
※The following table shows the available options for each property in “Setting Mode”
1. Printer Operation part Instruction
OPEN BUTTON
POWER Button Use same button as POS terminal Power Button
POWER BUTTON
OPEN Button Press to open Internal Printer cover.
Reset Button Reset & Enter setting mode
PAPER FEED Button
Press FEED Button to spew out Receipt paper.
You can make printer keep spewing out paper by
pressing FEED Button continuously.
PAPER OUT Lamp
Red light turns on when there is no receipt paper
in Printer.
PAPER FEED BUTTON
PAPER OUT LAMP
RESET BUTTON
PAPER FEED BUTTON
PAPER OUT LAMP
96000 BPS
Printing Method
Printing Speed
Dot Density (DPI)
Dot Pitch (mm)
Effective Printing Width
Printing Direction
Character/Line
Paper
Reliability
Character/Set
Barcode
Emulation
Driver
Interface
Power
Data Buffer
Cutting
Temperature
Qualification
Dimension
(W x H x D)
CE, FCC, KC
-
-
High Speed
(200mm/sec)
※ Please refer to the “Language setting” table for details.
Setting in order
Interface : Serial+USB+Ethernet
1. Step by Step
2. Serial Baudrate
3. Serial Parity-bit
4. Serial Handshaking
5. Error Sound
6. Density
7. Auto Cut
8. Auto Cut
9. Code Page
10. USB Mode
11. Paper Width
12. Paper Type
13. DHCP Mode (for Ethernet)
14. WiFi Mode (Not Support)
15. WiFi Channel (Not Supprt)
16. Black Mark Mode
17. Auto Load Mode
18. Sensing Level
HD
D
Warning
Instruction for low reliability or fire/electric shock/damage
1. Do not disassemble or remodeling the products except professional engineer.
2. Do not pour water or liquid into the system.
3. Ground the product before install the system.
4. Do not touch power cord during extreme thunder storm.
5. Do not touch power cord with wet hand.
6. Do not pull power cord or other peripheral device cables.
7. If abnormal smell, sound, or smoke is occurred, remove power cord immediately and
call to your close service center.
8. Do not use damaged power cord or plug (outlet).
9. Keep away the product and vinyl package from children.
-
Children can be choked, if they pull the vinyl over their head.
Caution
1. We recommend using proper power voltage (110V/220v) as a precaution against fire
and electrical shock
2. Before install the product, check suitable and safe place to use.
-
Find well ventilated place. Avoid the place close to possibility of fire.
-
Avoid high moisture and humidity.
3. Do not install or keep the product on steep place.
-
It can cause damage or malfunction by falling (crash).
4. Be aware of electro-static on PCB of system with anti-static appliance;
-
This may cause low reliability and short life term.
5. Place a product away from highly static areas.
6. Do not put metal or obstacle in product.
7. Use product in simple power cord plug-in circumstance.
8. Only use adapter supplied.
-
If an incorrect adapter is used, the product's performance may decrease and there
is an increased risk of explosion.
9. Use standard outer port.
-
Port can be damaged by connecting not standardized device.
PBQIG-IMPREX PRIME-E(Rev001;150623)
IMPREX PRIME
HDD LED
LAN LED
Power LED
Power switch
Printer (Option)
I/C card reader
(option)
Magnetic stripe reader
(option)
LCD&Touch
Panel display
Speakers
SPECIAL OPTION
I-Button
Smart card reader
magnetic stripe reader
Change
I/O Port Cover
Main board & HDD
USB Port (2ea)
※Caution: Power AC cord must be disconnected before
installing or removing optional device.
※ Detailed manual is packed together with optional device
individually.
*I/O ports may differ according to product model or options.
▶ Front View
▶ Side View
▶ Packing list
Cautions
!
5. Optional item
4. I/O specifications
1. Package contents
2. Configuration
3. Power connecting
The following items are included when you purchase this product.
If any of these items are damaged or missing, contact your dealer
for assistance
IMPREX PRIME
Installatin guide
Power cordAdapter
LED lamp changes following operation status.
▶ LED lamp
When connected LAN : LAN LED is blinking (Yellow)
Operation mode : HDD LED is blinking (Red)
Power LED is lit (Green)
Installation Guide
HDD + HDD case
MSR module
2nd Display
CDP
▶ CDP module
▶ 2nd Display
▶ MSR + SCR
▶ 2nd storage(HDD&SSD)-Order production
▶ LPT module
LPT
※Specifications may differ according to product model or options.
5-1. Optional illustration
Printer
▶ Printer module
Warning
Instruction for low reliability or fire/electric shock/damage
1. Do not disassemble or remodeling the products except professional engineer.
2. Do not pour water or liquid into the system.
3. Ground the product before install the system.
4. Do not touch power cord during extreme thunder storm.
5. Do not touch power cord with wet hand.
6. Do not pull power cord or other peripheral device cables.
7. If abnormal smell, sound, or smoke is occurred, remove power cord immediately and
call to your close service center.
8. Do not use damaged power cord or plug (outlet).
9. Keep away the product and vinyl package from children.
-
Children can be choked, if they pull the vinyl over their head.
Caution
1. We recommend using proper power voltage (110V/220v) as a precaution against fire
and electrical shock
2. Before install the product, check suitable and safe place to use.
-
Find well ventilated place. Avoid the place close to possibility of fire.
-
Avoid high moisture and humidity.
3. Do not install or keep the product on steep place.
-
It can cause damage or malfunction by falling (crash).
4. Be aware of electro-static on PCB of system with anti-static appliance;
-
This may cause low reliability and short life term.
5. Place a product away from highly static areas.
6. Do not put metal or obstacle in product.
7. Use product in simple power cord plug-in circumstance.
8. Only use adapter supplied.
-
If an incorrect adapter is used, the product's performance may decrease and there
is an increased risk of explosion.
9. Use standard outer port.
-
Port can be damaged by connecting not standardized device.
6 LAN
1 Power connector / 24V, 5A
Description Description
2 PS/2 connector
3 USB
5 VGA
4 COM1, COM2, COM3
▶
I/O Port : J1900
*I/O ports may differ according to product model or options.
6 LAN
1 Power connector / 24V, 5A
Description Description
2 PS/2 connector
3 USB
5 VGA
4 COM1, COM2, COM3
▶
I/O Port : Qs
1
unused
Check the model name/utility version and download the applicable utility on www.posbank.com
※CAUTION
- Disconnect cable with pulling the plug cap.
Cash drawer port
Power switch
Loading...