PORTMAN ELECTRONICS T69 SSI2W User Manual

OMPATIB

5-BUTTON LCD 2-WAY

QUICK START OPERATION GUIDE

Visit www.CarAlarm.com today

To Download the latest operation guide and learn more about system upgrades & other features!

PROGRAMMING REMOTES TO THE SYSTEM

Remote programming is dependant on the system being controlled. Please consult your dealer or the system guide for the proper
programming instructions.

Scan to register
& download the

Problems? Questions? Contact Customer Service:

800-554-4053 (toll free) | [phone] (outside USA)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna., Increase the separation
between the equipment and receiver., Connect the equipment into an outlet on a circuit different from that to which the receiver is connected., Consult the dealer or an experienced radio/TV technician for help.,

Warning! Changes or modifi cations made to this equipment not expressly approved by the part responsible for compliance could void the use’s authority to operate the equipment
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifi cations to this equipment. Such modifi cations could void the user’s authority to operate the equipment.

Copyright 2019 Omega Research & Development Technologies, Inc. OC_55308_20190712

latest operation

guide at

CarAlarm.com!

/omegard

/c/omegard

5-BUTTON LCD 2-WAY

QUICK START OPERATION GUIDE

REPLACING YOUR REMOTE BATTERY

STEPS REMOTE PART# BATTERY (QTY)

1) (551 only) Find the part # on the back of the remote to identify the battery.

2) (551 only) Locate the relief in case near the key chain and separate the case
halves to access & replace the batteries.

SECURITY, KEYLESS ENTRY, & CONVENIENCE FUNCTIONS

FUNCTION BUTTON(S) REMOTE CONFIRMATION NOTE

Lock & Arm*

Unlock & Disarm*

Silent Lock*

Silent Unlock*

Trunk/Hatch Release

Panic*

x 1

x 2

for 3 sec.

or for 3 sec.

“Lock” or ”arm” Displays

“Unlock” or ”D_Arm”

Displays

Beep

Beep

“TRUNK OPEN” Displays

“PANIC” Displays

The doors will lock.

The doors will unlock.

The doors will lock with no audible confi rmation.

Perform within 1 second. The doors will unlock with no
audible confi rmation.

By default, the system will also disarm/unlock.

The system will sound the horn/siren for Panic Mode.

Register today at www.CarAlarm.com

For warranty info & Download the latest operation guide.

553 Rechargable

551 CR2032

14

5-BUTTON LCD 2-WAY

5-BUTTON LCD 2-WAY

QUICK START OPERATION GUIDE

REMOTE START FUNCTIONS

FUNCTION

Engine Start/Stop

Run Time Extender*

Auto Start Mode*

BUTTON(S)

x 2

&

LCD CONFIRMATION

“START” + Melody

Chirp + “START ON”

“TEMP START ON” or

“TEMP START OFF”

Upon successful remote start the clock will display the remaining engine run time (M:SS).
Take Over: Turn ignition key ‘ON’, press brake pedal.

Clock will restart the run timer (only allowed once per remote start cycle).

Remote starts your vehicle every 2, 3, or 4 hours (programmable) or upon temperature threshold (set in the remote
start unit).

WINDOW-MOUNT ANTENNA/RECEIVER

Status LED

Valet / Programming Button

Status LED

*All functions are dependent upon vehicle & system availability. Consult your installer to confi rm feature availability.

2

NOTE

OTHER CONTROLLER FUNCTIONS

FUNCTION BUTTON(S)

Remote Valet*

Multi-Car

Button Lock

Status Update*

Power ON

Power OFF

Hold &

for 3 sec

Hold & for

3 sec

Hold &

for 3 sec

&

Hold

for 3 sec

,

,

x 2

,

x 3

&

Hold for 3 sec.

Hold for 5 sec.

LCD

CONFIRMATION

Beep + Screen fl ashes

Beep + ”Shift” icon

Beep + Screen fl ashes

Beep + Icons change

(if status has changed)

“AUX 1”

“AUX 2”

“AUX 3”

“AUX 4”

The screen will

turn on

The screen will

turn off

NOTE

This disables remote start and the security
system. The status LED will turn on. Repeat
this process or press valet button once to exit
valet mode.

The “Shift” icon appear when in car 2 opera­tion. Repeat to return to car 1 operation.

When button lock is on the remote will not
transmit. When any button is pressed the
screen will fl ash 5x. Repeat to unlock.

The screen icons will update to the current
status of the system.

AUX1 - Write function in “FUNCTION” column

AUX2 - Write function in “FUNCTION” column

AUX3 - Write function in “FUNCTION” column

AUX4 - Write function in “FUNCTION” column

The remote will resume all normal functions.

The remote will not function until powered on.

QUICK START OPERATION GUIDE

2WAY OPTIONS

OPTIONS PROCEDURE

Set Clock (H:M)

Set Alarm Clock (H:M)

Change Alarm Melody

Alarm Clock On/Off

Set Timer (H:M)

Set Timer Melody

Timer On/Off

Change Start/Stop Melody

12/24 Hour Clock

OTHER FEATURES BUTTON(S) LCD CONFIRMATION

Alarm Clock On/Off

Silent Mode On/Off

Parking Timer

*All functions are dependent upon vehicle & system availability. Consult your

Hold for 5 seconds. The controller will beep

indicating it has entered option programming.

Tap to scroll through each option.

Press

or to scroll through each option

setting.

Hold for 3 seconds or no activity for 15 seconds

to exit option programming

Melody + “Clock” icon

& .

Beep OR “Vibrate” icon.

&

Hold

& press

installer to confi rm feature availability.

Pressing

.

the timer length options.

will scroll thru

3