Portman P3 PIX3L User Manual

portman

custom lights

™

P3 PIX3L

USER MANUAL

© Portman Lights sp. z o.o.

 portmanlights.com

 /PortmanCustomLights

Designed and made in oland, EU

USER MANUAL – Portman Custom Lights P3 PIXEL

Welcome!

Dear User,

Thank you for choosing our P3 PIX3L. We are proud of delivering you the highest quality, the greatest
design and the real passion with our product. Each fixture in Portman P range is different, but all of
them ensure you the best performance and support your creativity.

If you have any questions, suggestions or require additional information contact us at:

[e-mail]

© 2016-2018 Portman Lights Sp. z o. o. All rights reserved.
The information and specifications are subject to change without notice. Portman Lights Sp. z o. o.
disclaims liability for any injury, damage, direct or indirect loss, consequential or economic loss or any
other loss occasioned by the use of, inability to use or reliance on the information contained in this user
manual.

USER MANUAL – Portman Custom Lights P3 PIX3L

Table of contents

Welcome! ................................................................................................................................................. 2

Table of contents ..................................................................................................................................... 3

Safety information ................................................................................................................................... 4

Technical specification ............................................................................................................................. 6

Fixture Overview ...................................................................................................................................... 7

Preparation for use .................................................................................................................................. 9

Lamp and fuse replacement .................................................................................................................. 11

Portman Spinner .................................................................................................................................... 12

Operation modes ................................................................................................................................... 14

Menu ...................................................................................................................................................... 15

USER MANUAL – Portman Custom Lights P3 PIXEL

Safety information

WARNING This product is for professional use only! It is not for household use.

P3 PIX3L presents risk of lethal or severe injury due to heat, electric shock, fire or falls.

Intense and flashing light could trigger epileptic seizures. Read this manual before your
initial start-up and follow the safety information in this manual and engraved on the
fixture.

Every person involved with the installation, operation and maintenance of this device

has to be qualified.

Before your initial start-up, please make sure that there is no damage caused by

transportation. Should there be any, consult your dealer and do not use the device.

Please consider that damages caused by manual modifications to the device are not

subject to warranty.

CAUTION! Keep this device away from rain and moisture!

CAUTION! Be careful with your operations! With a dangerous voltage you can suffer an

electrical shock when touching the fixture and wires!

CAUTION! During the operation the fixture surface becomes very hot. Allow the device
to cool approximately 30 minutes prior to manipulating with it. Keep a minimum 1 meter
distance from flammable materials to all exterior surfaces of the fixture

CAUTION! Avoid looking directly into the light source (meant especially for epileptics)!

CAUTION! Unplug mains lead before opening the housing, installing the lamp or the

fuse. Allow the device to cool approximately 1 hour prior to manipulating with it.

USER MANUAL – Portman Custom Lights P3 PIX3L

Protection against electrical shock

• Disconnect the fixture from AC power when not in use.

• Disconnect the fixture from AC power before any operation.

• Do not remove the rear cover. There are no user-serviceable parts inside.

• Always ground the fixture electrically.

• Use only the wires attached to the kit.

• Use only a source of AC power that complies with local building and electrical codes and has both

overload and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Replace the lamp or fuse only as described.

Protection against burns and fire

• Never operate when the fixture is damaged or some part is missing.

• Do not touch surface when the fixture is in operation. The exterior of the fixture can reach

temperatures up to 100°C (212°F). Allow the fixture to cool approximately 30 minutes before any
operation.

• Replace the lamp when it becomes defective or worn out.

• Never attempt to bypass the fuse. Always replace defective fuses with ones of the specified type

and rating.

• Keep all combustible and flammable materials (for example fabric, wood, paper) at a distance of at

least 1 meter away from the fixture. Do not cover the fixture when in operation and when it is hot.

• Do not modify the fixture.

• Do not operate the fixture if the ambient air temperature exceeds 45°C (113°F).

• Do not operate the fixture after extreme change of surrounding environment temperature. Allow

the fixture to acclimate for at least an hour before operating.

Protection against falls

• Use only professional tripods and clamps to mount the fixture or Portman Spinner structure.

• Ensure that the structure intended for installation can hold at least 10 times the weight of all

installed devices or Portman Spinner structure.

• Ensure that all fixtures are attached correctly to the structure, after having checked that the housing

is firmly closed and all screws are tightly fastened and use an approved means of secondary
attachment such as a safety cable.

• Block access below the work area whenever installing or removing the fixture.

• Do not mount more than 7 fixtures per single structure build with Portman Spinner.

• When building a structure with Portman Spinners ensure that each fixture is connected to at least

two Portman Spinners and whole structure is attached to mounting surface with at least two
clamps.

Protection against eyesight damage and epileptic seizure

• Do not stare directly into the light. Never look at an exposed lamp while it is lit.

• Provide advance notice that flash light is in use.

• Avoid long cycles of rapid flashing light.