Porter & Charles CC60V Operating And Installation Instructions
OPERATING AND INSTALLATION INSTRUCTIONS
SLIDER CONTROL BUILT-IN VITROCERAMIC COOKER
EN
Porter&Charles
CC60V
CONTENTS:
1
DESCRIPTION OF THE COOKTOP
SAFETY INSTRUCTIONS
INSTALLATON
Locating Your Built-in cooktop
Electrical Connection of Your cooktop
USAGE
Turn On and Turn Off The Control
Select Zone
Turn on dual- and triple zones
Set Cooking Level With and Without Heat Boost
Turn Off Individual Heaters
Timer Function
Key Lock
Child Lock
Stop & Go
TOUCH CONTROL SAFETY FUNCTIONS
Sensor Safety Cut Off
Over Temperature Switch Off
Operating Time Limitations
Residual Heat Functions
CLEANING AND CARE
WARRANTY&SERVICE
2
DESCRIPTION OF THE HOB
Dear Customer,
It is important that you should read this manual for best performance and
to extend the life of your appliance. We recommend you to keep this manual
for future reference.
Your new cooktop is guaranteed and will give lasting service. This guarantee
is only applicable if the appliance has been installed and operated in
accordance with the operating and installation instructions detailed in this
manual.
Note: Appearance of your cooktop maybe different than the model shown above
due to its configuration.
SINGLE ZONE
HEATER
OVAL ZONE
HEATER
COOKTOP
FRAME
VITROCERAMIC
SURFACE
TOUCH CONTROL
PANEL
3
SAFETY INSTRUCTIONS
READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE USING YOUR APPLIANCE,
AND KEEP IT IN A CONVENIENT PLACE FOR REFERENCE WHEN NECESSARY.
THIS MANUAL IS PREPARED FOR MULTIPLE SIMILAR COOKTOPS.YOUR APPLIANCE
MAY NOT HAVE SOME OF THE FEATURES THAT ARE EXPLAINED IN THIS MANUAL.
REFER TO THE
TO THE EXPRESSIONS THAT HAVE FIGURES,
WHILE YOU
ARE READING THE OPERATING
MANUAL.
General Safety Warnings
- This appliance can be used by children aged
from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
- WARNING: The appliance and its accessible
parts become hot during use. Care should be
taken to avoid touching heating elements. Children
less than 8 years of age shall be kept away unless
continuously supervised.
- WARNING: Unattended cooking on a hob with
fat or oil can be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but
switch off the appliance and then cover flame e.g.
with a lid or a fire blanket.
- WARNING: Danger of fire: do not store items
on the cooking surfaces.
- WARNING: If the surface is cracked, switch off
the appliance to avoid the possibility of electric
shock
.
MODEL NUMBER OF YOUR UNIT
4
- For cooktop incorporating a lid, any spillage should
be removed from the lid before opening. And also
the hob surface should be allowed to cool before
closing the lid.
- The appliance is not intended to be operated by
means of an external timer or separate remotecontrol system.
- Do not use harsh abrasive cleaners or sharp
metal scrapers to clean the oven door glass and
other surface since they can scratch the surface,
which may result in shattering of the glass or
damage to the surface.
- Do not use steam cleaners for cleaning the
appliance.
- Your appliance is produced in accordance with all applicable local and international standards and
regulations.
- Maintenance and repair work must be made only by authorized service technicians. Installation and
repair work that is carried out by unauthorized technicians may endanger you. It is dangerous to alter
or modify the specifications of the appliance in any way.
- Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure
or electricity voltage and frequency) and the requirements of the appliance are compatible. The
requirements for this appliance are stated on the label.
- CAUTION: This appliance is designed only for cooking food and is intended for indoor domestic
household use only and should not be used for any other purpose or in any other application, such as
for non-domestic use or in a commercial environment or room heating.
- All possible security measures have been taken to ensure your safety. Since the glass may break, you
should be careful while cleaning to avoid scratching. Avoid hitting or knocking on the glass with accessories.
- Ensure that the supply cord is not wedged during the installation. If the supply cord is damaged, it must
be replaced by the manufacturer, its service agent or similarly qualified persons in order to prevent a
hazard.
Installation Warnings
- Do not operate the appliance before it is fully installed.
- The appliance must be installed by an authorized technician and put into use. The producer is not
responsible for any damage that might be caused by defective placement and installation by unauthorized
people.
- When you unpack the appliance, make sure that it is not damaged during transportation. In case of
any defect; do not use the appliance and contact a qualified service agent immediately. As the materials
used for packaging (nylon, staplers, styrofoam...etc) may cause harmful effects to children, they should
be collected and removed immediately.
- Protect your appliance against atmospheric effects. Do not expose it to effects such as sun, rain, snow
etc.
- The surrounding materials of the appliance (cabinet) must be able to withstand a temperature of min
100°C.
5
The electrical connection of this cooktop should be carried out by an
authorised service
technician
or a qualified electrician, according to the
instructions in this guide and in compliance with the current regulations.
· Before connecting your appliance to the mains at home, make sure to
check the conformity of voltage settings, which are specified on the information
sticker attached to the appliance and/or packaking, with the usage conditions
available.
· The laws, ordinances, directives and standards in force in the country of
use are to be followed (safety regulations, proper recycling in accordance
with the regulations, etc.)
Installing your built-in cooktop
After removing the packaging material from the appliance and its accessories,
ensure that the hob is not damaged. If you suspect any damage, do not use
the appliance and contact an authorised service technician a qualified
electrician immediately.
· This built-in
cooktop
is to be inserted into a cut out in a counter.
INSTALLATION
· Create an opening with the dimensions shown in next picture . The distance
between the rear edge of the cooktop and any adjacent wall is depend on
wall
surface. Please don’t use easily combustible material like curtain, paper
at
nearby cooktop.
During usage
- Do not put flammable or combustible materials, in or near the appliance when it is operating.
- Do not leave the cooker while cooking with solid or liquid oils. They may catch fire on condition of
extreme heating. Never pour water on to flames that are caused by oil. Cover the saucepan or frypan
with its cover in order to choke the flame that has occured in this case and turn the cooker off.
- Always position pans over the centre of the cooking zone, and turn the handles to a safe position so
they cannot be knocked or accidentally.
- If you will not use the appliance for a long time, unplug it at the main control.
- Make sure the appliance control knobs are always in the "0" (stop) position when it is not used.
During cleaning and maintenance
- Always turn the appliance off at the main control cleaning or maintenance. You can do it after
plugging the appliance off or turning the main switches off.
- Do not remove the control knobs to clean the control panel.
TO MAINTAIN THE EFFICIENCY AND SAFETY OF YOUR APPLIANCE, WE RECOMMEND YOU
ALWAYS USE ORIGINAL SPARE PARTS AND TO CALL ONLY OUR AUTHORIZED SERVICE AGENTS
IN CASE OF NEED EURO PARTS:1800.678.8352.
6
· Screw the 4 worktop mounting brackets on the side walls of product.
· Apply the one-sided self-adhesive sealing tape supplied all the way round
the lower edge of the cooking surface along the outer edge of the glass
ceramic panel. Do not stretch it.
worktop mounting bracket
Neighboorhood walls A [mm] B [mm]
Combustible 60 150
Non-combustible 25 40
Making an electrical connection
Before making a connection, check that:
· The mains voltage is the same as that quoted on the rating plate which
is situated at the back of your hob.
· The circuit can support the appliance load (see the rating plate).
· The power supply has an earth connection, which complies with the
provisions of current regulations and is in good working order.
· The fused switch is easily accessible once the has been
installed.
If there is no dedicated hob circuit and fused switch, they must be
installed by a qualified electrician before the is connected.
cooktop
cooktop
An approved suitable cable must be connected from the Consumer Unit
main fuse box and be protected by its own 32amp fuse or Micro Circuit
Breaker (MCB). The electrician must provide a fused all pole switch,
which disconnects both the line (live) and neutral conductors with a
contact seperation of at least 3,0 mm.
The fused switch should be fitted to the kitchen wall, above the
worksurface and to the side of the hob, not above it, in accordance with
IEE regulations. Connect the fused switch to a junction box which should
be fitted on the wall about 61cm (24 inches) above floor level and behind
the The 's power supply cable can then be connected.
Connect one end to the junction box and connect the other end to the
's power connection box which is located at the back of the hob.
Remove the cover of the power connection box and install the cable, in
accordance with the connection diagram.
cooktop. cooktop
cooktop
7
Electrical connection diagram
For the induction the cable must be suitable for region will be
used. You will find the connection diagram shown on the bottom of your
appliance.
cooktop,
8
* This appliance must be earthed.
* For this connetion a power lead of wire type
10 AWG should be used.
L
N
PE
BLACK
RED
GREEN
Mode Descriptions
USAGE
The appliance is operated by touching buttons and the functions are
confirmed by displays and acoustic signals.
9
Stand-By-Mode S-Mode
The mains are applied to the cooktop control
and all zone displays are off or a residual
heat display is active.
Operating-Mode
B-Mode
At least one heater display shows a heat
setting between ´0` and ´9`
Lock Mode
VR-Mode
The cooktop control is locked.
Heat Setting/
Timer Sliding
Heat Setting/
Timer Sliding
Indicator
Stop/Go
Zone
Display
Zone
10
Turn On and Turn Off The Appliance
If the appliance is in Stand-By-Mode, it is put in Operating-Mode by pressing
the On/Off button at least 1 second. A buzzer signal indicates the
successful operation acoustically.
On all zones a ´0` appears and all Decimal Points of the zone flashes (1
sec on, 1 sec off).
If there is no operation within 10 sec, the display of all zones will turn off.
If the displays are turned off, the zone will be set into Stand-By-Mode.
If is pressed more than 2 sec (in Operating-Mode), the appliance is
switched off and is set into the S-Mode again. The appliance can be turned
off by pressing at any time; even if other buttons are pressed
simultaneously.
If there is a residual heat of a heater remaining, this will be indicated in the
correspondent heat setting Zone Display.
Select Zone
If a single
zone
is chosen with the corresponding zone Active/Deactive
Zone
Button , the Decimal Point of the related Heater Display flashes.
For the
selected heater, you can set the heat level between 1-9 by touching the
Heat Setting Slider Buttons
The slider button must be pressed within 3 sec, otherwise the zone selection
is erased and heat setting dot will disappear (Decimal Point). If there is no
further operation within 10 sec, the heater falls back into the S-Mode.
The heat setting can always be changed by pressing between
level 1-9.
Each sliding operation or each display change is quitted by a buzzer signal.
Turn on dual and triple zones (available only in some models)
Turn on the dual zone
The activation of the dual zone is done after selecting the desired zone
by actuating . This is confirmed by a buzzer signal. At the same time, the
corresponding Dual Zone Indicator goes on statically. Touching for a
second time, the status of the dual zone toggles: it changes from dual zone
on to dual zone off and back again.
The extension zone can be activated only, after a level between 1-9 is set
on the basic zone of the heater.
Turn on triple zones
A dual or triple zone can only be switched on, if the basic zone of a zone
is set to level 1–9 and the heater is selected, the dot is on.
If is pressed, the buzzer signal sounds and the Dual Zone Indicator is
statically on. If is pressed once again, there is another acoustical signal
and the triple heater is switched on. The Triple Zone Indicator will be
illuminated and the triple zone will be energized.
After touching once again, the triple zone of the heater will be switched
off again. Each operation causes a status change of the dual/triple zones
following in this manner (Dual zone on, triple zone on, all extended zones
off, dual zone on, triple zone on, dual zone on, etc. ...)
Set Cooking Level With and Without Heat Boost
All zones are equipped with heat boost functionality.
If the heat boost is active, than the zone will be operated with maximum
power for the period of the heat boost time, that is dependent from the
selected heat setting. This is indicated through a flashing ´A`, alternating
with the heat setting value (e.g. 0,5 sec ´A` and 0,5 sec ´9`) in the zone
display. Once the heat boost time ended only the heat setting will be indicated.
If the heat boost should be used for a zone , touch or slide heat level 0, than
touch heat level 9 again. After setting the heat to level 9 , ´A` will be indicated
alternating. This means that level 9 and heat boost is active now.
12
The heat boost can be turned off by sliding until heat setting ´0` appears.
Turn Off Individual Heaters
A selective zone can be turned off with 3 different ways:
. Simultaneous operation of right and left part of the slider button
· Reduction of the heat setting to ´0` by pressing right and the left part of the
slider button
· Use of timer turn off function for the corresponding the zone.
Loading...