Porter-Cable QUICKSAND 335 User Manual

Double Insulated

Random Orbit Sander

MODEL 335

Instruction

manual

The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

IMPORTANT

Please make certain that the person who
is to use this equipment carefully reads
and understands these instructions before
starting operations.

ESPAÑOL: PÁGINA 13
FRANÇAISE : PAGE 27

Part No. 900007 (012)

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

Copyright © 2001 PORTER-CABLE Corporation

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 1

2

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using electric tools, basic safety precautions should

always be followed to reduce the risk of fire, electric shock and personal
injury, including the following:

WARNING: SOME DUST CREATED BY POWER SANDING, SAWING,

GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES

contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:

· lead from lead-based paints,

· crystalline silica from bricks and cement and other masonry products, and

· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.

READ AND FOLLOW ALL INSTRUCTIONS.

There are certain applications for which this tool was designed. Porter-Cable
strongly recommends that this tool NOT be modified and/or used for any
application other than for which it was designed. If you have any questions
relative to its application DO NOT use the tool until you have written Porter­Cable and we have advised you.

Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305

POLARIZED PLUGS: To reduce the risk of electric shock, this equipment
has a polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not change the plug in any way.

1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

2. AVOID DANGEROUS ENVIRONMENT. Don’t expose power tools to

rain. Don’t use power tools in damp or wet locations. Keep area well lit.
Avoid chemical or corrosive environment. Do not use tool in presence of
flammable liquids or gases.

3. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with
grounded surfaces. For example: pipes, radiators, ranges, refrigerator
enclosures.

4. KEEP CHILDREN AWAY. Do not let visitors contact tool or extension
cord. All visitors should be kept away from work area.

5. STORE IDLE TOOLS. When not in use, tools should be stored in dry,
and high or locked-up place – out of reach of children.

6. DON’T FORCE TOOL. It will do the job better and safer at the rate for
which it was intended.

7. USE RIGHT TOOL. Don’t force small tool or attachment to do the job of
a heavy duty tool. Don’t use tool for purpose not intended – for example – do
not use a circular saw for cutting tree limbs or logs.

8. DRESS PROPERLY. Do not wear loose clothing or jewelry. Loose
clothing, draw strings and jewelry can be caught in moving parts. Rubber
gloves and non-skid footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 2

3

9. USE SAFETY GLASSES. Wear safety glasses or goggles while

operating power tools. Also face or dust mask if operation creates dust. All
persons in the area where power tools are being operated should also wear
safety glasses and face or dust mask.

10. DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect
from receptacle. Keep cord from heat, oil, and sharp edges. Have damaged
or worn power cord and strain reliever replaced immediately. DO NOT
ATTEMPT TO REPAIR POWER CORD.

11. SECURE WORK. Use clamps or a vise to hold work. It’s safer than using
your hand and it frees both hands to operate tool.

12. DON’T OVERREACH. Keep proper footing and balance at all times.

13. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better

and safer performance. Follow instructions for lubricating and changing
accessories. Inspect tool cords periodically and if damaged, have repaired by
authorized service facility. Inspect extension cords periodically and replace if
damaged. Have all worn, broken or lost parts replaced immediately. Keep
handles dry, clean and free from oil and grease.

14. DISCONNECT TOOLS when not in use, before servicing, and when
changing accessories such as blades, bits, cutters, etc.

15. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of
checking to see that keys and adjusting wrenches are removed from the tool
before turning it on.

16. AVOID UNINTENTIONAL STARTING. Do not carry a plugged-in tool with
finger on switch. Be sure switch is off when plugging in. Keep hands, body and
clothing clear of blades, bits, cutters, etc. when plugging in the tool.

17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use
only extension cords marked “Suitable for use with outdoor appliances –
store indoors when not in use.”

18. STAY ALERT. Watch what you are doing. Use common sense. Do not
operate tool when you are tired or while under the influence of medication,
alcohol or drugs.

19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or
other part that is damaged should be carefully checked to determine that it
will operate properly and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized service
center unless otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by authorized service center. Do not use tool if
switch does not turn it on and off.

20. WEAR EAR PROTECTION to safeguard against possible hearing loss.

SAVE THESE INSTRUCTIONS

ADDITIONAL SAFETY RULES FOR RANDOM ORBIT SANDERS

1. ALWAYS DISCONNECT the sander cord plug from the power circuit

before changing abrasive sheets.

2. USE DUST MASK. Wear a protective mask to minimize breathing in the
fine dust created while sanding.

3. DO NOT RUN TOOL WITH BACK-UP PAD REMOVED. Resulting
vibration could cause loss of control.

4. DO NOT OPERATE TOOL WITH DUST SHROUD REMOVED. The dust
shroud covers high-speed rotating parts.

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 3

4

5. KEEP HANDS AND BODY PARTS AWAY from rotating disc. Contact

with rotating disc cause severe cuts and abrasions.

6. NEVER RUN SANDER with dust container or dust collector assembly
removed. Dust could be blown into eyes.

7. WEAR EYE AND FACE PROTECTION. Injury to face and eyes can
result if disc flies off or pad ruptures. Wear impact resistant glasses and full
face shield.

8. USE PROPER SAFETY EQUIPMENT. Wear safety goggles to protect
your eyes and wear a protective mask to minimize breathing in the fine dust
created while sanding. NOTE: Some wood contains preservatives which can
be toxic. Take extra care to prevent inhalation and skin contact when working
with these materials.

9. SANDING OF LEAD BASED-PAINT IS NOT RECOMMENDED. Lead­based paint should only be removed by a professional.

ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

WARNING: Extreme care should be taken when removing paint. The

peelings, residue, and vapors of paint may contain lead, which is
poisonous. Exposure to even low levels of lead can cause
irreversible brain and nervous system damage; young and unborn
children are particularly vulnerable.

Before beginning any paint removal process you should determine whether
the paint you are removing contains lead. This can be done by your local
health department or by a professional who uses a paint analyzer to check for
lead.

LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY A PROFESSIONAL.
Persons removing paint should follow these guidelines:

1. KEEP THE WORK AREA WELL VENTILATED. Open the windows and
put an exhaust fan in one of them. Be sure the fan is moving air from inside to
outside.

2. REMOVE OR COVER any carpets, rugs, furniture, clothing, cooking
utensils and air ducts.

3. PLACE DROP CLOTHS in the work area to catch any paint chips or
peelings. Wear protective clothing such as extra work shirts, overalls and hats.

4. WORK IN ONE ROOM AT A TIME. Furnishings should be removed or
placed in the center of the room and covered. Work areas should be sealed
off from the rest of the dwelling by sealing doorways with drop cloths.

5. CHILDREN, PREGNANT OR POTENTIALLY PREGNANT women and
nursing mothers should not be present in the work area until the work is done
and all cleanup is complete.

6. WEAR A DUST RESPIRATOR or a dual filter (dust and fume) respirator
mask which has been approved by the Occupational Safety and Health
Administration (OSHA), the National Institute of Safety and Health (NIOSH), or
the United States Bureau of Mines. These masks and replaceable filters are
readily available at major hardware stores. Be sure the mask fits. Beards and
facial hair may keep the masks from sealing properly. Change filters often.
DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.

7. KEEP FOOD AND DRINK out of the work area. Wash hands, arms, and
face and rinse mouth before eating or drinking. Do not smoke or chew gum
or tobacco in the work area.

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 4

5

8. CLEAN UP ALL REMOVED PAINT and dust by wet mopping the floors.

Use a wet cloth to clean all walls, sills and any other surfaces where paint or
dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high
phosphate detergent or trisodium (TSP) to wash and mop areas.

9. AT THE END OF EACH WORK SESSION put the paint chips and debris
in a double plastic bag, close it with tape or twist ties and dispose of properly.

10. REMOVE PROTECTIVE CLOTHING and work shoes in the work area to
avoid carrying dust into the rest of the dwelling. Wash work clothes
separately. Wipe shoes off with a wet rag that is then washed with the work
clothes. Wash hair and body thoroughly with soap and water.

REPLACEMENT PARTS

When servicing use only identical replacement parts.

MOTOR

Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown
on the specification plate on the tool. Several models, however, are designed
for A.C. current only. Refer to the specification plate on your tool for proper
voltage and current rating.

CAUTION: Do not operate your tool on a current on which the
voltage is not within correct limits. Do not operate tools rated A.C.
only on D.C. current. To do so may seriously damage the tool.

EXTENSION CORD SELECTION

If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and
possible motor damage. A table of recommended extension cord sizes will
be found in this section. This table is based on limiting line voltage drop to 5
volts (10 volts for 230 volts) at 150% of rated amperes.

If an extension cord is to be used outdoors it must be marked with the
suffix W-A following the cord type designation. For example – SJTW-A to
indicate it is acceptable for outdoor use.

RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS

Length of Cord in Feet

115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft.
230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft.

0-2 18 18 18 16 16 14 14 12 12
2-3 18 18 16 14 14 12 12 10 10
3-4 18 18 16 14 12 12 10 10 8
4-5 18 18 14 12 12 10 10 8 8
5-6 18 16 14 12 10 10 8 8 6
6-8 18 16 12 10 10 8 6 6 6

8-10 18 14 12 10 8 8 6 6 4
10-12 16 14 10 8 8 6 6 4 4
12-14 16 12 10 8 6 6 6 4 2
14-16 16 12 10 8 6 6 4 4 2
16-18 14 12 8 8 6 4 4 2 2
18-20 14 12 8 6 6 4 4 2 2

Nameplate Ampere Rating

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 5

6

OPERATING INSTRUCTIONS

FOREWORD

The Porter-Cable Random Orbit Sander provides rapid stock removal with 80
to 100 grit abrasive and swirl-free finishing with 120 to 150 grit abrasive. The
Sander is equipped with a reversible pad that can accept 6" diameter, six
hole (for six dust extraction) abrasives, with either STIKIT™ adhesive backed
type attachment or hook & loop type attachment.

TO START AND STOP SANDER

1. CAUTION: Make certain the switch is in the “OFF” position, and the
power source is the same as that specified on the tool’s nameplate.

2. Connect the tool to the power source.

CAUTION: Keep hands and body parts away from rotating disc.
Contact with rotating disc can cause severe cuts and abrasions.

3. The switch button, (A) Fig. 1, is labeled “ON” and “OFF”. Depress the
“ON” end of the switch button to start motor. Depress the “OFF” end of the
switch button to stop motor.

REVERSIBLE PAD

The pad is factory assembled with the hook & loop side exposed (for use
with hook & loop type abrasives). If you wish to use STIKIT™ type abrasives,
it will be necessary to reverse the pad as follows:

1. CAUTION: DISCONNECT THE SANDER FROM THE POWER SOURCE.

2. Remove three screws (A) Fig. 2, and lift pad (B), from sander.

3. Remove three spacers (C) Fig. 3, from the pad.

4. Re-install the three spacers (C) in the hook & loop side of the pad.

5. Orient the pad with its hook & loop side toward the sander. Align three
mounting holes with the corresponding holes in the pad mount.

6. Re-install the three screws (A) Fig. 2. Tighten firmly (20 to 25 in. lbs. of
torque).

7. Reverse the above procedure to return to hook & loop abrasives.

Fig. 1

A

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 6

7

INSTALLING/REMOVING ABRASIVE DISC
Hook & Loop Abrasive:

The “hook” side of the sanding pad must be exposed for use with hook &
loop abrasives (see REVERSIBLE PAD).

1. CAUTION: DISCONNECT MACHINE FROM POWER SOURCE.

2. Place machine on workbench with pad up (see Fig. 4).

3. Clean dust from pad face.

4. Position Hook & Loop Abrasive Disc onto sander pad, aligning the dust
extraction holes in paper with holes in pad.

CAUTION: Do not use PSA (Pressure Sensitive Adhesive) disc with
Hook & Loop pad as the disc may be thrown from the pad causing
personal injury.

5. Press disc firmly onto pad.

CAUTION: Failure to properly seat disc to pad may result in disc
being thrown from pad causing personal injury.

6. To remove disc, peel disc away from pad.

Fig. 2

Fig. 3

Fig. 4

Fig. 5

A

B

C

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 7

Pressure Sensitive Abrasive:

The smooth side of the sanding pad must be exposed for use with pressure
sensitive abrasives (see REVERSIBLE PAD).

1. CAUTION: DISCONNECT MACHINE FROM POWER SOURCE.

2. Place machine on workbench with pad up (see Fig. 5).

3. Clean dust from pad face.

4. Tear a new abrasive disc from roll and position disc to the sander pad.
Align the dust extraction holes in paper with holes in pad.

5. Press disc firmly onto pad.

6. Position machine with abrasive contacting scrap material. Start machine
and operate momentarily while exerting firm pressure to seat disc to pad.

CAUTION: Failure to properly seat disc to pad may result in disc
being thrown from pad causing personal injury.

7. To remove disc, peel disc away from pad.

NOTE: Do not store machine with an abrasive disc installed. Heat
generated by the sanding operation increases the adhesive bond
between the disc and pad. If disc is left on pad for an extended time
after use, it can become difficult to remove.

DUST COLLECTOR

1. CAUTION: DISCONNECT SANDER FROM POWER SOURCE.

2. Position dust collector (A) Fig. 6, to sander nozzle (B). Seat collector onto
nozzle.

3. Periodically remove dust container (A) Fig. 7, from flange (B), and empty
collected dust.

8

Fig. 7

B

A

Fig. 6A

A

B

C

Fig. 6B

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 8

NOTE: A slight twisting action will ease removal and reassembly.

Tap container lightly to remove compacted dust. DO NOT WASH CONTAINER.
Dry compressed air may be used to blow out container.

CAUTION: Wear safety glasses while using compressed air.

The dust collector flange contains a clear plastic disc (C) Fig. 7, that acts as a
check valve to prevent collected dust from getting back into the sander. DO
NOT REMOVE THIS DISC.

CAUTION: Never run sander with dust container or dust collector
assembly removed. Dust could be blown into eyes.

The dust collector can be rotated around the body of the sander. It may be
used in any convenient position, Fig. 8.

The dust collector may be replaced with Accessory Hose #39332 so that tool
can be used with a remote vacuum system.

HOW TO HOLD SANDER

The sander is designed to be held either around the main housings, Fig. 9, or
by the top of the main housings, Fig. 10. When sanding for long periods, it is
recommended you periodically alternate between the two holding positions.

PAD BRAKE

These sanders are equipped with a pad brake that prevents over-speeding of
the pad. If the tool is lifted off the work surface while the motor is running, the
brake will limit pad rotation to no more than 400 RPM.

The pad brake uses a belt to provide the braking action. Eventually, this belt
may require replacement. If the brake fails to limit pad rotation, send the
sander to a Porter-Cable service facility or replace the belt yourself as
explained under BELT REPLACEMENT in the MAINTENANCE SECTION of
this manual.

9

Fig. 9 Fig. 10

Fig. 8A

Fig. 8B

Fig. 8C

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 9

10

USING THE SANDER

1. CAUTION: Secure work to prevent if from moving during the sanding
operation. Friction between the sanding disc and work will try to spin work
away from sander and may cause bodily injury.

2. CAUTION: WEAR SAFETY GLASSES AND DUST MASK.

3. Place sander pad in light contact with the work before switching the
motor “ON”.

4. Grasp sander firmly and move switch to “ON” position.

5. Move sander in long overlapping strokes. Tipping sander or stopping in
one spot can produce an uneven finish.

6. When finished, keep pad in contact with work, move switch to “OFF”
position and lift sander from the work. Allow pad rotation to stop completely
before setting sander down.

MAINTENANCE

KEEP TOOL CLEAN

Periodically blow out all air passages with dry, compressed air. Remove
buildup of grime resulting from working with green or sappy wood. All plastic
parts should be cleaned with a soft damp cloth. NEVER use solvents to clean
plastic parts.

CAUTION: Wear safety glasses while using compressed air.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug
are making good contact in the outlet. Also, check for blown fuses or open
circuit breakers in the line.

BRUSH INSPECTION AND LUBRICATION

At approximately 200 hours of use, take or send your tool to your nearest
Authorized Porter-Cable Service Station to be thoroughly cleaned and
inspected; worn parts replaced, when necessary; relubricated with fresh
lubricant, if required; reassembled with new brushes; and performance
tested.

Any loss of power before the above maintenance check may indicate the
need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE
TOOL UNDER THIS CONDITION. If proper operating voltage is present,
return your tool to the Service Station for immediate service.

BELT REPLACEMENT

1. CAUTION: DISCONNECT SANDER FROM POWER SOURCE.

2. Remove back-up pad (see REVERSIBLE PAD).

3. Remove the old belt and clean the belt mounting area.

4. Position the new belt around pulley (A) Fig. 11, and start it onto the
shoulder of the pad support (B).

5. Rotate the pad support as you “walk” the belt onto it (see Fig. 12).

6. Reassemble back-up pad (see CHANGING BACK-UP PAD).

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 10

11

SERVICE AND REPAIRS

All quality tools eventually require servicing or replacement of parts due to
wear from normal use. These operations, including brush inspection and
replacement, should ONLY be performed by either an AUTHORIZED
PORTER-CABLE SERVICE STATION or PORTER-CABLE SERVICE CENTER.
All repairs made by these agencies are fully guaranteed against defective
material and workmanship. We cannot guarantee repairs made or attempted
by anyone other than these agencies.

Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).

ACCESSORIES

The testing of this tool has been accomplished with the following
accessories. For safest operation, it is recommended that only these
accessories be used with this product.

WARNING: Since accessories other than those listed have not been
tested with this product, use of such accessories could be
hazardous.

13700 Replacement Pad 5” Standard Profile
13701 Replacement Pad 5” Contour
13906 Replacement Pad 6” Dual Sided
13950 Dust Canister
875403 Dust Container
899536 Dust Filter Assembly (includes flange & valve assembly)
39332 Vacuum Hose

Fig. 11

Fig. 12

B

A

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 11

12

PRESSURE CATALOG NO. GRIT QUANTITY/PKG.
SENSITIVE 72 660 06 25 60 25
ABRASIVES 72 660 08 50 80 50

72 660 10 10 100 10
72 660 10 50 100 50
72 660 12 50 120 50
72 660 15 10 150 10
72 660 15 50 150 50
72 660 22 10 220 10
72 660 22 50 220 50

HOOK & LOOP

CATALOG NO. GRIT QUANTITY/PKG.

ABRASIVES 73 660 06 05 60 5

73 660 06 25 60 25
73 660 08 25 80 25
73 660 10 05 100 5
73 660 10 25 100 25
73 660 12 25 120 25
73 660 15 05 150 5
73 660 15 25 150 25
73 660 22 05 220 5
73 660 22 25 220 25

PORTER-CABLE LIMITED

ONE YEAR WARRANTY

Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.

ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.

To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 12

The following are trademarks of PORTER-CABLE •DELTA Corporation (Las siguientes son marcas registradas de PORTER-CABLE •DELTA
S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE

•

DELTA Corporation): BAMMER®, LASERLOC®,

OMNIJIG

®

, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®, QUICKSAND®, SANDTRAP®, SAW BOSS®, SPEED-

BLOC

®

, SPEEDMATIC®, SPEEDTRONIC®, STAIR-EASE®, THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, TIGER CUB®, TIGER

SAW

®

, TORQ-BUSTER®, VERSA-PLANE®, WHISPER SERIES®, DURATRONIC™, FRAME SAW™, INNOVATION THAT WORKS™,

JETSTREAM™, MICRO-SET™, MORTEN™, NETWORK™, RIPTIDE™, TRU-MATCH™, WOODWORKER’S CHOICE™.

Trademarks noted with ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países. Marques déposées, indiquées par la lettre ®, sont déposées au Bureau des brevets d’invention et marques
déposées aux Etats-Unis et pourraient être déposées aux autres pays.

PORTER-CABLE • DELTA SERVICE CENTERS

(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)

(CENTRE DE SERVICE PORTER-CABLE • DELTA)

Parts and Repair Service for Porter-Cable •Delta Power Tools are Available at These Locations

(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable

•

Delta)

(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)

Authorized Service Stations are located in many large cities. Telephone [phone] or 901-541-6042 for assistance locating one. Parts
and accessories for Porter-Cable

•

Delta products should be obtained by contacting any Porter-Cable •Delta Distributor, Authorized

Service Center, or Porter-Cable

•

Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will

be directed to the nearest Porter-Cable

•

Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en

muchas grandes ciudades. Llame al 800-487-8665 ó al 901-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los
accesorios para los productos Porter-Cable

•

Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable

•

Delta, Centro de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable •Delta. Si no tiene acceso a ninguna de estas
opciones, llame al 888-848-5175 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable

•

Delta más cercano. Des centres de service

agréés sont situés dans beaucoup de grandes villes. Appelez au 800-487-8665 ou au 901-541-6042 pour obtenir de l’aide pour en
repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-Cable

•

Delta, s’adresser à tout distributeur Porter-Cable

•

Delta, centre de service agréé ou centre de service d’usine Porter-Cable •Delta. Si vous n’avez accès à aucun de ces centres, appeler le

888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable

•

Delta le plus proche.

ARIZONA

Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: [phone]
Fax: [phone]

CALIFORNIA

Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: [phone]
Fax: [phone]

San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: [phone]
Fax: [phone]

FLORIDA

Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: [phone]
Fax: [phone]

Tampa 33609
4538 W. Kennedy Boulevard
Phone: [phone]
Fax: [phone]

GEORGIA

Forest Park 30297 (Atlanta)
5442 Frontage Road, Suite 112
Phone: [phone]
Fax: [phone]

ILLINOIS

Addison 60101 (Chicago)
311 Laura Drive
Phone: [phone]
Fax: [phone]

Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: [phone]
Fax: [phone]

MARYLAND

Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: [phone]
Fax: [phone]

MASSACHUSETTS

Braintree 02185 (Boston)
719 Granite Street
Phone: [phone]
Fax: [phone]

Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: [phone]
Fax: [phone]

MICHIGAN

Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: [phone]
Fax: [phone]

MINNESOTA

Minneapolis 55429
4315 68th Avenue North
Phone: [phone]
Fax: [phone]

MISSOURI

North Kansas City 64116
1141 Swift Avenue
P.O. Box 12393
Phone: [phone]
Fax: [phone]

St. Louis 63119
7574 Watson Road
Phone: [phone]
Fax: [phone]

NEW YORK

Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: [phone]
Fax: [phone]

NORTH CAROLINA

Charlotte 28270
9129 Monroe Road, Suite 115
Phone: [phone]
Fax: [phone]

OHIO

Columbus 43214
4560 Indianola Avenue
Phone: [phone]
Fax: [phone]

Cleveland 44125
8001 Sweet Valley Drive Unit #19
Phone: [phone]
Fax: [phone]

OREGON

Portland 97230
4916 NE 122 nd Ave.

Phone: [phone]
Fax: [phone]

PENNSYLVANIA

Willow Grove 19090
520 North York Road
Phone: [phone]
Fax: [phone]

TEXAS

Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: [phone]
Fax: [phone]

Houston 77055
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: [phone]
Fax: [phone]

WASHINGTON

Renton 98055 (Seattle)
268 Southwest 43rd Street
Phone: [phone]
Fax: [phone]

Printed in U.S.A.

CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS

ALBERTA

Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: [phone]
Fax: [phone]

BRITISH COLUMBIA

8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: [phone]
Fax: [phone]

MANITOBA

1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: [phone]
Fax: [phone]

ONTARIO

505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: [phone]
Fax: [phone]

QUÉBEC

1515 Ave.
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: [phone]
Fax: [phone]

1447, Begin
St-Laurent, (Montréal), Québec
H4R 1V8
Phone: [phone]
Fax: [phone]

900007 - 02-28-01.QXD 9/26/02 11:46 AM Page 44