Porter-Cable PCXB620DP Instruction Manual
1
10 IN. (254 MM) DRILL PRESS
PERCEUSE À COLONNE DE 254 MM
(10 PO)
254 MM (10 PULGADAS)
PERFORADORA DE COLUMNA
CATALOG NUMBER
PCXB620DP
Instruction Manual
Manuel d’instructions
Manual de instrucciones
www.portercable.com
INSTRUCTIVO DE OPERACIÓN,
CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
2
2016/09
TABLE OF CONTENTS
SECTION PAGE
PRODUCT SPECIFICATIONS ................................................................................... 2
CALIFORNIA PROPOSITION 65................................................................................ 3
SAFETY GUIDELINES - DEFINITIONS ..................................................................... 3
POWER TOOL SAFETY ............................................................................................. 4
ADDITIONAL SAFETY RULES FOR DRILL PRESSES.............................................. 6
ELECTRICAL REQUIREMENTS AND SAFETY ........................................................ 8
TOOLS NEEDED FOR ASSEMBLY ........................................................................... 10
CARTON CONTENTS ................................................................................................ 10
KNOW YOUR DRILL PRESS ....................................................................... 12
GLOSSARY OF TERMS.............................................................................................. 13
ASSEMBLY AND ADJUSTMENTS ............................................................................. 14
OPERATION ............................................................................................................... 19
MAINTENANCE .......................................................................................................... 23
ACCESSORIES AND ATTACHMENTS ...................................................................... 23
TROUBLESHOOTING GUIDE ................................................................................... 24
PARTS LIST................................................................................................................. 26
WARRANTY................................................................................................................. 28
PRODUCT SPECIFICATIONS
To avoid electrical hazards, re hazards or damage to the tool, use proper circuit
protection. Use a separate electrical circuit for your tools. The drill press is wired at the
factory for 120 Volt operation. It must be connected to a 120 V, 3.2 AMP branch circuit
and use a 3.2 AMP time delay fuse or circuit breaker. To avoid shock or re, replace
power cord immediately if it is worn, cut or damaged in any way.
Printed in China
WARNING
!
MOTOR TABLE
Power Source .…. 120 V, 60 Hz, 3.2 A Size ................................. 7-5/8 in. x 6-1/2 in.
Speed (No load) .. 1720 RPM (194 x 165 mm)
Type .................... Induction BASE
Volts .................... 120 volts AC only Size .................................
12-1/2 in. x 7-5/16 in.
LAMP................... Yes
(319 x 186 mm)
Spindle Travel ..... 2 in. (50 mm) Chuck to Column ............
5 in. (127 mm)
Speeds (RPM) .... 610~2800 RPM Chuck to Base ................
16-9/64 in. (410 mm)
Chuck Size .......... 1/2 in. (12.7 mm)
Column Size ....... 1-7/8 in. (48 mm)
3
WARNING ICONS
Your power tool and its Instruction Manual may contain “WARNING ICONS” (a picture symbol
intended to alert you to and/or instruct you how to avoid a potentially hazardous condition).
Understanding and heeding these symbols will help you operate your tool better and safer.
Shown below are some of the symbols you may see.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
Some dust created by power sanding, sawing, grinding, drilling and other construction
activities contains chemicals known to the state of California to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
● Lead from lead-based paints,
● Crystalline silica from bricks and cement and other masonry products, and
● Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed
to lter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling and
other construction activities. Wear protective clothing and wash exposed areas with soap
and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
Use of this tool can generate and/or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.
SAFETY GUIDELINES - DEFINITIONS
CALIFORNIA PROPOSITION 65
SAFETY ALERT: Precautions that involve your safety.
PROHIBITION
WEAR EYE PROTECTION: Always wear safety goggles or safety glasses with
side shields.
WEAR RESPIRATORY AND HEARING PROTECTION: Always wear respiratory and hearing
protection.
READ AND UNDERSTAND INSTRUCTION MANUAL: To reduce the risk of injury, user and
all bystanders must read and understand instruction manual before using
this product.
KEEP HANDS AWAY FROM THE MOVING PART AND CUTTING SURFACE: Failure to
keep your hands away from the moving part and cutting surface will result in serious personal
injury.
SUPPORT AND CLAMP WORK
WARNING
!
WARNING
!
WARNING
!
CAUTION
DANGER
!
CAUTION
!
4
POWER TOOL SAFETY
GENERAL SAFETY INSTRUCTIONS
BEFORE USING THIS POWER TOOL
Safety is a combination of common sense,
staying alert and knowing how to use your
power tool.
● To avoid mistakes that could cause
serious injury, do not plug the tool in
until you have read and understood the
following.
● Read all instructions before operating
product. Failure to follow all
instructions listed below may result
in electric shock, re and/or serious
injury.
1. READ and become familiar with the
entire Instruction Manual. LEARN
the tool’s application, limitations and
possible hazards.
2. KEEP GUARDS IN PLACE and in working
order.
3. REMOVE ADJUSTING KEYS AND
WRENCHES. Form the habit of checking
to see that keys and adjusting wrenches
are removed from the tool before turning
ON.
4. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
5. DO NOT USE IN DANGEROUS
ENVIRONMENTS. Do not use power tools
in damp locations, or expose them to rain
or snow. Keep work area well lit.
6. KEEP CHILDREN AWAY. All visitors and
bystanders should be kept a safe distance
from work area.
7. MAKE WORKSHOP CHILD PROOF with
padlocks, master switches or by removing
starter keys.
8. DO NOT FORCE THE TOOL. It will do the
job better and safer at the rate for which it
was designed.
9. USE THE RIGHT TOOL. Do not force the
tool or an attachment to do a job for which
it was not designed.
10. USE PROPER EXTENSION CORDS.
Make sure your extension cord is in good
condition. When using an extension cord,
be sure to use one heavy enough to
carry the current your product will draw.
An undersized cord will result in a drop
in line voltage and in loss of power which
will cause the tool to overheat. The table
on page 9 shows the correct size to use
depending on cord length and nameplate
ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge
number, the heavier the cord.
11. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets or other jewelry which may get
caught in moving parts. Nonslip footwear
is recommended. Wear protective hair
covering to contain long hair.
12. ALWAYS WEAR EYE
PROTECTION. Any power tool
can throw foreign objects into
the eyes and could cause permanent
eye damage. ALWAYS wear Safety
Goggles (not glasses) that comply with
ANSI Safety standard Z87.1. Everyday
eyeglasses have only impact–resistant
lenses. They ARE NOT safety glasses.
NOTE: Glasses or goggles not in
compliance with ANSI Z87.1 could
seriously injure you when they break.
13. WEAR A FACE MASK OR
DUST MASK. Sawing operation
produces dust.
14. SECURE WORK. Use clamps
or a vise to hold work when
practical. It is safer than using
your hand and it frees both hands to
operate the tool.
15. DISCONNECT TOOLS FROM POWER
SOURCE before servicing, and when
changing accessories such as blades,
bits and cutters.
WARNING
!
5
16. REDUCE THE RISK OF
UNINTENTIONAL STARTING. Make
sure switch is in the OFF position before
plugging the tool in.
17. USE RECOMMENDED ACCESSORIES.
Consult this Instruction Manual for
recommended accessories. The use of
improper accessories may cause risk of
injury to yourself or others.
18. NEVER STAND ON THE TOOL. Serious
injury could occur if the tool is tipped
or if the cutting tool is unintentionally
contacted.
19. CHECK FOR DAMAGED PARTS. Before
further use of the tool, a guard or other
part that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended function
– check for alignment of moving parts,
binding of moving parts, breakage of
parts, mounting and any other conditions
that may affect its operation. A guard or
other part that is damaged should be
properly repaired or replaced.
20. NEVER LEAVE THE TOOL RUNNING
UNATTENDED. TURN THE POWER
“OFF”. Do not walk away from a running
tool until the blade comes to a complete
stop and the tool is unplugged from the
power source.
21. DO NOT OVERREACH. Keep proper
footing and balance at all times.
22. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for
lubricating and changing accessories.
23. DO NOT use power tool in presence of
ammable liquids or gases.
24. DO NOT operate the tool if you are under
the inuence of any drugs, alcohol or
medicationn that could affect your ability
to use the tool properly.
25. Dust generated from certain materials
can be hazardous to your health. Always
operate saw in well-ventilated area and
provide for proper dust removal.
26.
People with electronic devices, such
as pacemakers, should consult their
physician(s) before using this product.
Operation of electrical equipment in
close proximity to a heart pacemaker
could cause interference or failure of the
pacemaker.
27. WEAR HEARING PROTECTION
to reduce the risk of induced
hearing loss.
WARNING
!
6
ADDITIONAL SAFETY RULES FOR DRILL PRESS
10. SECURE THE WORK. Use clamps or a
vise to hold the work. It’s safer than using
your hand and it frees both hands to
operate tool.
11. WHEN using a drill press vise, always
fasten to the table.
12. MAKE SURE all clamps and locks are
rmly tightened before drilling.
13. MAKE SURE there are no nails or foreign
objects in the part of the workpiece to
be drilled.
14. SECURELY LOCK THE HEAD and table
support to the column, and the table to
the table support before operating the
drill press.
15. NEVER turn your drill press on before
clearing the table of all objects (tools,
scraps of wood, etc.). Remove material or
debris from the area that might be ignited
by hot chips.
16. Crowded, cluttered work areas that can
cause tripping or loss of balance are
particularly dangerous.
17. BEFORE STARTING the operation, jog
the motor switch to make sure the drill bit
does not wobble or vibrate.
18. LET THE SPINDLE REACH FULL
SPEED before starting to drill. If your drill
press makes an unfamiliar noise or if it
vibrates excessively, stop immediately,
turn the drill press off and unplug. Do
not restart the unit until the problem is
corrected.
19. DO NOT perform layout assembly or set
up work on the table while the drill press
is in operation.
20. USE THE RECOMMENDED SPEED
for any drill press accessory and for
different workpiece material. READ THE
INSTRUCTIONS that come with the
accessory.
21. WHEN DRILLING large diameter holes,
clamp the workpiece rmly to the table.
Otherwise, the bit may grab and spin the
workpiece at high speeds. DO NOT USE
y cutters or multiple-part hole cutters,
as they can come apart or become
unbalanced in use.
Following good safety practices when using
drill presses is a must. Make a habit of
including safety in all your activities.
READ ALL INSTRUCTIONS BEFORE
OPERATING PRODUCT. FAILURE TO
FOLLOW ALL INSTRUCTIONS LISTED
BELOW MAY RESULT IN ELECTRIC
SHOCK, FIRE AND OR SERIOUS INJURY.
Do not operate this tool until it is assembled
and installed according to the instructions.
1. YOUR DRILL PRESS MUST BE
BOLTED securely to a workbench. In
addition, if there is any tendency for
your drill press to move during certain
operations, bolt the workbench to the
oor.
2. DO NOT try to drill material too small to
be securely held.
3. ALWAYS keep hands out of the path of
a drill bit. Avoid awkward hand positions
where a sudden slip could cause your
hand to move into the drill bit.
4. DO NOT install or use any drill bit that
exceeds 7 in. (175 mm) in length or
extends 6 in. (150 mm) below the chuck
jaws. They can suddenly bend outward or
break.
5. DO NOT USE wire wheels, router bits,
shaper cutters, circle (y) cutters, or
rotary planers on this drill press.
6. WHEN cutting a large piece of material,
make sure it is fully supported at the table
height.
7. NEVER hold the work piece by hand.
Secure the work piece with a clamp or
another appropriate xture if it is not long
enough to be braced against the table
column.
8. CLAMP THE WORKPIECE OR BRACE
IT against the left side of the column to
prevent rotation. If it is too short or the
table is tilted, clamp it solidly to the table.
9. IF THE WORKPIECE overhangs the table
such that it will fall or tip if not held, clamp
it to the table or provide auxiliary support.
WARNING
!
7
22. DO NOT use bits with screw tips. These
bits will pull the workpiece up from the
table and start to spin, causing a serious
risk of injury.
23. MAKE SURE the spindle has come to
a complete stop before touching the
workpiece.
24. TO AVOID INJURY from accidental
starting, always turn the switch “OFF” and
unplug the drill press before installing or
removing any accessory or attachment or
making any adjustment.
25. Be sure the chuck is tightly secured to
the spindle.
26. USE ONLY THE SELF-EJECTING TYPE
CHUCK KEY as provided with the drill
press. Tighten the bit securely in the
chuck. The chuck key can be thrown at a
high velocity if not removed, causing risk
for injury.
27. DO NOT FORCE DRILLING. The tool will
do the job better and safer at the rate for
which it is was intended.
28. If the bit binds in the workpiece, release
the on/off switch immediately. Unplug the
tool, then free the bit from the workpiece.
Do not try to free a jammed bit by starting
and stopping the tool.
29. DO NOT touch the drill bit or cuttings.
The drill bit and cuttings are hot
immediately after drilling.
30. ALWAYS shut off, unplug and lock the
drill press, if a lock in available, and store
the key.
8
POWER SUPPLY AND MOTOR
SPECIFICATIONS
To avoid electrical hazards, re hazards,
or damage to the tool, use proper circuit
protection. Use a separate electrical circuit
for your tool. Your grinder is wired at the
factory for 120 V operation. Connect to a
120 V, 3.2 Amp circuit and use a 3.2 Amp
time delay fuse or circuit breaker. To avoid
shock or re, if power cord is worn, cut,
or damaged in any way, have it replaced
immediately.
GROUNDING INSTRUCTIONS
This tool must be grounded while in use to
protect the operator from electrical shock.
IN THE EVENT OF A MALFUNCTION OR
BREAKDOWN, grounding provides a path
of least resistance for electric currents and
reduces the risk of electric shock. This tool
is equipped with an electrical cord that has
an equipment-grounding conductor and a
grounding plug. The plug must be plugged
into a matching receptacle that is properly
installed and grounded in accordance with all
local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED.
If it will not t the receptacle, have the proper
receptacle installed by a qualied electrician.
IMPROPER CONNECTION of the equipment
grounding conductor can result in risk of
electric shock. The conductor with the green
insulation (with or without yellow stripes) is
the equipment grounding conductor. If repair
or replacement of the electrical cord or plug
is necessary, do not connect the equipment
grounding conductor to a live terminal.
CHECK with a qualied electrician or service
person if you do not completely understand
the grounding instructions, or if you are not
certain the tool is properly grounded.
USE only 3-wire extension cords that have
three-pronged grounding plugs with threepole receptacles that accept the tool’s
plug. Repair or replace damaged or worn
cords immediately.
ELECTRICAL REQUIREMENTS AND SAFETY
WARNING
!
Use a separate electrical circuit for your tool.
This circuit must not be less than #18 wire
and should be protected with a 3.2 Amp time
lag fuse. Before connecting the motor to the
power line, make sure the switch is in the off
position and the electric current is rated the
same as the current stamped on the motor
nameplate. Running at a lower voltage will
damage the motor.
GUIDELINES FOR EXTENSION CORDS
USE THE PROPER EXTENSION CORD.
Make sure your extension cord is in good
condition. Use an extension cord heavy
enough to carry the current your product
will draw. An undersized cord will cause
a drop in line voltage resulting in loss of
power, overheating and burning out of the
motor. The table below shows the correct
size to use depending on cord length and
nameplate ampere rating. If in doubt, use the
next heavier gauge. The smaller the gauge
number, the heavier the cord.
Make sure your extension cord is properly
wired and in good condition. Always replace a
damaged extension cord or have it repaired by
a qualied technician before using it. Protect
your extension cords from sharp objects,
excessive heat and damp or wet areas.
MINIMUM GAUGE FOR EXTENSION CORDS (AWG)
(When usng 120 volts only)
Ampere Rating Total length of Cord
More Than Not More Than
25 50 100 150 ft.
(7.62 15.24 30.48 45.72 m)
AWG- American Wire Gauge
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12
Not Recommended
WARNING
!
9
This tool is for indoor use only. Do not expose
to rain or use in damp locations.
This tool is intended for use on a circuit that
has a receptacle like the one illustrated in
Fig. 1. Fig. 1 shows a three-pronged electrical
plug and receptacle that has a grounding
conductor. If a properly grounded receptacle
is not available, an adapter (Fig. 2) can be
used to temporarily connect this plug to
a two-contact grounded receptacle. The
adapter (Fig. 2) has a rigid lug extending from
it that MUST be connected to a permanent
earth ground, such as a properly grounded
receptacle box.
In all cases, make certain the receptacle is
properly grounded. If you are not sure, have a
qualied electrician check the receptacle.
WARNING
!
CAUTION
!
Fig. 1
Fig. 2
Three-Pronged Plug
Grounding Prong
Properly Grounded
Three-Pronged
Receptacle
Grounding Lug
Make sure this is
connected to a
known ground.
Two-Pronged
Receptacle
Adapter
Loading...