Porter-Cable PCX362010 Instruction Manual
10-IN PORTABLE TABLE SAW
Français (#)
Español (#)
www.portercable.com
Instruction Manual
To reduce the risk of serious injury, thoroughly read and comply with all warnings and instructions in this manual and on product.
KEEP THIS MANUAL NEAR YOUR SAW FOR EASY REFERENCE AND TO INSTRUCT OTHERS
PCX362010
TABLE OF CONTENTS
FUNCTIONAL DESCRIPTION .................................................. 2
IMPORTANT SAFETY INSTRUCTIONS ................................... 2
SAFETY SYMBOL-DEFINITIONS ....................................... 3
GENERAL POWER TOOL SAFETY RULES ........................ 3
PROPOSITION 65 WARNING ............................................ 4
TABLE SAW SAFETY RULES .............................................. 5
SAW BLADE GUARD, ANTI-KICKBACK PAWLS AND
RIVING KNIFE ASSEMBLY.................................................. 6
MAKING A PUSH STICK ..................................................... 6
KICKBACKS ........................................................................ 7
POWER CONNECTIONS .......................................................... 8
POWER SOURCE ............................................................... 8
EXTENSION CORDS ........................................................... 8
UNPACKING ..............................................................................8
SHIPPING CONTENTS ....................................................... 9
CONTENTS OF HARDWARE BAG ................................... 10
GENERAL PARTS KNOWLEDGE ........................................... 11
ASSEMBLY ............................................................................... 11
STAND ASSEMBLY ........................................................... 11
ATTACHING SAW TO STAND ........................................... 13
FENCE RAIL AND EXTENSION WING ASSEMBLY.......... 13
HEIGHT ADJUSTMENT KNOB INSTALLATION ............... 14
INSTALLING/CHANGING THE BLADE ............................. 14
POSITION THE RIVING KNIFE .......................................... 15
INSERT AND LEVEL THROAT PLATE ............................... 15
ANTI-KICKBACK PAWLS AND BLADE GUARD............... 16
RIP FENCE ........................................................................ 17
OPERATION ............................................................................. 18
TURNING THE SAW ON AND OFF ................................... 18
MAKING CUTS ........................................................................ 19
RIP CUTS .......................................................................... 20
BEVEL RIPPING ................................................................ 20
CROSSCUTTING .............................................................. 21
BEVEL CROSSCUTTING .................................................. 21
MITER CUTS ..................................................................... 21
COMPOUND MITER CUTS............................................... 22
LARGE PANEL CUTS ........................................................22
NON-THROUGH CUTS ..................................................... 22
MAKING A NON-THROUGH CUT .................................... 22
CUTTING AIDS AND ACCESSORIES .................................... 23
PUSH STICK ..................................................................... 23
AUXILIARY MITER GAUGE FACING ................................. 24
PUSH BLOCK .................................................................... 24
FEATHERBOARD .............................................................. 25
CUT OFF GAUGE .............................................................. 25
JIGS ................................................................................... 25
MAKING ADJUSTMENTS ....................................................... 26
LEVELING THE THROAT PLATE ....................................... 26
CHANGING THE BEVEL ................................................... 26
ADJUSTING THE BEVEL STOPS ..................................... 26
ADJUSTING THE BLADE HEIGHT.................................... 27
USING THE MITER GAUGE .............................................. 27
RIVING KNIFE ADJUSTMENT .......................................... 27
MAINTENANCE ....................................................................... 29
TROUBLE SHOOTING ............................................................ 29
ACCESSORIES ........................................................................ 29
WARRANTY ............................................................................. 30
FRENCH ..................................................................................... #
SPANISH .....................................................................................#
FUNCTIONAL DESCRIPTION
SPECIFICATIONS
The PORTER CABLE PCX362010 10-inch
Portable Table Saw is designed for high quality
performance. Includes: saw, stand, miter gauge,
15-amp motor, on/off switch, fixed extension wing,
see-through blade guard with anti-kickback pawls,
riving knife, and 10-inch carbide tooth blade.
NOTICE: The manual cover illustrates the current production model. All other illustrations contained in the manual are
representative only and may not be exact depictions of the actual labeling or accessories included. They are intended for
illustrative purposes only.
Max depth of cut at 90 degrees: 3”
Max depth of cut at 45 degrees: 2-1/2”
Max rip to right of blade: 16”
Max rip to left of blade: 8”
MOTOR SPECIFICATIONS
Amps 15 Amps
Voltage 120 Volts
IMPORTANT SAFETY INSTRUCTIONS
CAREFULLY READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS ON YOUR
PRODUCT AND IN THIS MANUAL. SAVE THIS MANUAL. MAKE SURE ALL USERS ARE
FAMILIAR WITH ITS WARNINGS AND INSTRUCTIONS WHEN USING THE TOOL. Improper operation, maintenance
or modification of tools or equipment could result in serious injury and/or property damage.
If you have any questions or concerns relative to the use of your tool or the contents of this manual, stop using the tool
and contact customer support at 1-844-816-8986.
2 3
SAFETY SYMBOLS- DEFINITIONS
The definitions below describe the level of severity of each signal word. Please read the manual and pay attention to
these symbols.
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
NOTICE:
Used without the safety alert symbol indicates a practice which, if not avoided, may result in property
damage.
GENERAL POWER TOOL SAFETY RULES
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
1. READ INSTRUCTION MANUAL AND KNOW
YOUR TOOL. Read and familiarize yourself
with the entire instruction manual. Learning the
tool’s proper applications, limitation, and specific
potential hazards will greatly minimize the
possibility of accidents and injury. Make sure all
users are familiar with its warnings and instructions
before using.
2. MAINTAIN TOOLS WITH CARE. Keep tools
sharp and clean for best and safest performance.
Follow instructions for lubricating and changing
accessories.
3. KEEP GUARDS AND SAFETY DEVICES IN
PLACE and working properly.
4. CHECK TOOLS FOR DAMAGE. Before using,
and after tool or accessory has been dropped or
damaged, check guards and affected parts, for
alignment, breakage and any other condition that
may affect its operation to make sure tool will
operate properly and all parts will perform their
intended function. Do not use a damaged product.
A guard or any other part that is damaged should
be properly repaired or replaced using factory
approved service parts.
5. NEVER STAND ON TOOL. Serious injury could
occur if the tool tips or if you unintentionally
contact the cutting surface.
6. WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts.
Nonslip protective footwear is recommended. Wear
protective hair covering to contain long hair.
7. WEAR PROPER EYE PROTECTION. All persons
in work area should wear safety glasses with side
shields. Everyday eye glasses with impact resistant
lenses are not safety glasses. Eye equipment
should comply with ANSI Z87.1 standards.
8. WEAR PROPER HEARING PROTECTION. All
people in work area should wear proper hearing
protection consistent with noise levels and
exposure. Hearing equipment should comply with
ANSI S3.19 standards.
9. DUST PROTECTION. Use of power tools can
generate and/or disburse dust, which may cause
serious or permanent respiratory or other injury,
including silicosis (a serious lung disease), cancer,
and death. Direct particles away from face and
body. Always operate tool in a well-ventilated
area and provide for proper dust removal. Use
dust collection system whenever possible. Avoid
breathing dust and avoid prolonged contact with
dust. Allowing dust to get into your mouth or eyes,
or lay on your skin may promote absorption of
harmful material. Use properly fitting NIOSH/OSHA
approved respiratory protection appropriate for the
dust exposure and wash exposed areas with soap
and water.
10. LOCK TOOLS AND WORK AREA. Use padlocks,
and master switches, or remove and store starter
keys to prevent operation by children and other
unauthorized users.
11. DO NOT USE OR STORE TOOL IN DANGEROUS
ENVIRONMENTS. Exposure to rain and damp or
wet locations can result in shock or electrocution,
or damage the tool. Do not operate electric tools
near flammable liquids or in gaseous or explosive
atmospheres. Motors and switches in these tools
may spark and ignite fumes.
12. KEEP WORK AREA CLEAN AND WELL LIT.
Cluttered and poorly-lit work areas, surfaces and
benches can lead to accidents.
13. KEEP CHILDREN AND BYSTANDERS AWAY
from work area.
14. USE RECOMMENDED ACCESSORIES. Consult
manual for recommended accessories. Use of
inappropriate accessories may cause personal
injury or property damage.
15. DISCONNECT TOOL from power source before
servicing, adjusting or changing set-ups or blades,
bits, cutters and other accessories.
16. TO REDUCE RISK OF ACCIDENTAL STARTING
make sure power switches are in “OFF” position
before plugging tool in.
17. TO REDUCE THE RISK OF ELECTRIC SHOCK,
this equipment has a polarized plug (one blade is
wider than the other). This plug will fit in a polarized
outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install the proper
outlet. Do not change the plug in any way.
18. DO NOT touch the plug’s metal prongs when
unplugging or plugging in the cord.
19. USE PROPER EXTENSION CORD. If you use an
extension cord, make sure it is in good condition
3
GENERAL POWER TOOL SAFETY RULES (CONTINUED)
and heavy enough to carry the current your product
will draw. An undersized cord will cause a drop
in line voltage, resulting in loss of power and
overheating. See Extension Cord Chart for correct
size depending on cord length and data plate
ampere rating. If in doubt, use the next smaller
gauge number. The smaller the gauge number, the
heavier the cord. When working outside, make
sure the extension cord is rated for outdoor use.
Consult power connection section of this manual
for Extension Cord Chart and power connection
safety.
20. DO NOT ABUSE POWER CORDS. NEVER yank
cord to disconnect from receptacle, crush cord, or
expose it to heat, oil or sharp objects.
21. USE PROPER TOOL. Do not force tool to do a
task for which it was not designed.
22. SECURE WORKPIECE. Use clamps or a vise to
hold the workpiece when practical. It is safer than
using your hands and frees both hands to operate
tool.
23. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that all adjusting
PROPOSITION 65 WARNING:
keys and wrenches are removed before starting
tool.
24. STAY ALERT, WATCH WHAT YOU ARE DOING,
AND USE COMMON SENSE. Do not use power
tools when tired or under the influence of drugs,
alcohol, or medication. A moment of inattention
while operating power tools may result in injury.
25. USE PROPER FEED DIRECTION. Feed
workpiece against the direction of rotation of the
tool’s blade, cutter, or abrasive surface. Feeding in
the other direction may cause the workpiece to be
thrown at high speed.
26. DO NOT OVERREACH. Keep proper footing and
balance to maintain control.
27. DO NOT FORCE TOOL OR WORKPIECE.
Operate tool at intended speed and feed rate for
better and safer operation.
28. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Do not leave tool until it
comes to a complete stop. In the event of a power
failure, move switch to “OFF” position.
29. SERVICE PARTS. Use only identical replacement
parts when servicing your tool.
Dust created by power sanding, sawing, grinding, drilling, and other construction activities may
contain chemicals known to the state of California to cause cancer, birth defects or other
reproductive harm. Some examples are:
– Lead from lead-based paints
– Crystalline silica from bricks and cement and other masonry products
– Asbestos dust
– Arsenic and chromium from chemically-treated lumber
• Your risk from these exposures varies depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well-ventilated area and work with approved safety equipment, such as
dust masks that are specifically designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction
activities. Wear protective clothing and wash exposed areas with soap and water
If you have any questions or concerns relative to the use of your tool or the contents of this manual, stop using the
tool and call PORTER CABLE Customer Care at 1-844-816-8986.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
If tool is loaned to someone, also loan them these instructions.
4 5
TABLE SAW SAFETY RULES
TERMINOLOGY
The following terms will be used throughout the manual and you should become familiar with them.
— Through-cut - any cut that completely cuts through
the workpiece.
— Non-through cut - any cut that does not completely
cut through the workpiece.
— Push stick - a wooden or plastic stick, usually
homemade, that is used to push a small workpiece
through the saw and keeps the operator’s hands
clear of the blade. (See illustration 26 on page 23)
— Kickback - when the saw blade binds in the cut or
the workpiece binds between the blade and the
fence and the workpiece is thrust back toward the
operator.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
• SEE GENERAL POWER TOOL SAFETY SECTION OF THIS MANUAL. Read entire instruction manual
before operating saw. Learning the saw’s proper applications, limitations, and specific potential hazards will
greatly minimize the possibility of accidents and injury. Make sure all users are familiar with its warnings and
instructions before using saw.
• SEE POWER CONNECTION SECTION OF THIS MANUAL for instructions and warnings regarding power
cords and connections.
— Freehand - cutting without the use of a miter
gauge or rip fence or any other means of guiding
or holding the workpiece other than the operator’s
hand.
— Plunge cutting - blind cuts in the workpiece made
by either raising the blade through the workpiece or
lowering the workpiece down to the blade.
— Re-sawing - flipping the workpiece to complete a
cut the saw is not capable of making in one pass.
— Cove cutting - an operation where the work is fed at
an angle across the blade. (Also known as “coving”)
1. AVOID KICKBACK. Pay particular attention to the
instructions (below) for reducing risk of kickback.
2. OBTAIN ADVICE from your supervisor,
instructor, or another qualified person if you are
not thoroughly familiar with the operation of this
machine. Knowledge is safety.
3. DRESS PROPERLY. Wear appropriate apparel,
eye protection, hearing protection and dust
protection as specified in the General Power Tool
Safety Section of this manual.
4. PROPER ASSEMBLY. Do not operate this saw until
it is completely assembled and installed according
to the instructions.
5. STABILITY. Make sure table saw is properly
assembled and located on a stable surface before
use to keep saw from moving during cut.
6. USE CORRECT BLADE AND RIVING KNIFE for
the intended operation. The blade must be installed
so the points of the teeth are pointing toward the
front of the saw. Do not use oversized blade or
blade with incorrect arbor opening. Always tighten
the blade arbor nut securely. Before use, inspect
the blade for cracks or missing teeth. Do not use
a damaged or dull blade. Always use blade within
the thickness range for which the riving knife is
designed.
7. USE PROPER THROAT PLATE. The proper throat
plate must be in place and properly secured at all
times to reduce the risk of a thrown workpiece and
possible injury.
8. USE SAW BLADE GUARD, RIVING KNIFE
AND ANTI-KICKBACK PAWLS. Your saw
is equipped with a modular blade guard, riving
knife and anti-kickback pawl assembly, each
component of which should be used for every
possible operation, including all through cuts. This
assembly is discussed in more detail below. Make
sure components are securely installed prior to
operation.
9. NEVER CUT METALS, CEMENT BOARD OR
MASONRY. Certain man-made materials have
special instructions for cutting on table saws.
Follow the manufacturer’s recommendations at all
times.
10. SUPPORT YOUR WORKPIECE based on its size
and the type of operation to be performed. Hold
the workpiece firmly against the fence and down
against the table surface. Do not leave a wide
panel or long board (or other large workpiece)
unsupported – the weight of the workpiece may
causes it to shift on the table resulting in loss of
control.
11. NEVER PERFORM LAYOUT, ASSEMBLY OR SETUP WORK ON THE TABLE/WORK AREA when
the saw is running.
12. USE A PUSH STICK that is appropriate to the
application to push and hold down a workpiece
through the completion of the cut. A push stick is
a wooden or plastic stick, usually homemade, that
should be used whenever the size or shape of the
workpiece would cause you to place your hands
within 6 in. (152 mm) of the blade. Instructions for
making a push stick are included in this manual. A
push stick is also provided with this saw.
13. NEVER Perform freehand cutting, plunge cutting,
re-sawing, or cove cutting.
14. CHECK WORKPIECE AND SET-UP before
each operation. Knots, irregularities, or nails
in workpiece and positioning mistakes or
incomplete set-up may interfere with or affect saw
performance and personal safety.
15. NO FREEHAND CUTS. Always use a rip fence,
miter gauge, or other appropriate devices to guide
or hold down the workpiece. Use hold-downs, jigs,
5
TABLE SAW SAFETY RULES
fixtures or feather boards to help guide and control
The workpiece. Accessories for use with your saw
are available at extra cost from your local dealer or
authorized service center.
16. DO NOT USE RIP FENCE AND MITER GAUGE
AT THE SAME TIME.
17. AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause a
hand to move into a saw blade. Operate with table
at or near waist level for maximum balance and
control. Anticipate effect of workpiece size on
your ability to adjust position and maintain control
through completion of cut.
18. KEEP ARMS, HANDS AND FINGERS AT LEAST
SIX INCHES AWAY FROM THE BLADE.
19. KEEP HANDS AND OTHER BODY PARTS OUT
OF THE BLADE PATH. NEVER have any part of
your body in line with the path of the saw blade.
20. NEVER START THE MACHINE WITH THE
WORKPIECE AGAINST THE BLADE to reduce
the risk of a thrown workpiece.
21. DO NOT REACH OVER/REACH AROUND. Never
reach over, in back of, or around the cutting tool
with either hand while the blade is in motion.
22. NEVER ATTEMPT TO FREE A STALLED BLADE
OR TRAPPED WORKPIECE without first turning
the machine off and disconnecting the saw from
the power source.
23. BEFORE LEAVING THE SAW, wait for the blade to
come to a complete stop, then disconnect from the
power source, clean the table and work area, and
lock out switch to prevent unauthorized use.
24. AN UNFAMILIAR NOISE OR EXCESSIVE
VIBRATION may indicate a problem with your
saw. If this happens, turn it off and disconnect it
from the power source until the problem has been
located and corrected. Contact customer service
for assistance if the problem cannot be solved.
SAW BLADE GUARD, ANTI-KICKBACK PAWLS AND RIVING KNIFE
ASSEMBLY
Your table saw is equipped with a blade guard, antikickback pawls and riving knife assembly that covers
the blade and reduces the possibility of accidental
blade contact. The riving knife is a flat plate that fits
into the cut made by the saw blade and effectively
fights kickback by lessening the tendency of the blade
to bind in the cut. Two anti-kickback pawls are located
on the sides of the riving knife that allow the wood
to pass through the blade in the cutting direction but
reduce the possibility of the material being thrown
backwards toward the operator. The blade guard and
anti-kickback pawls can only be used when making
through cuts that sever the wood. When making
rabbets and other non-through cuts, the blade guard
and anti-kickback pawls must be removed and riving
knife lowered to the non-through cut position marked
on the riving knife.
Use all components of the guarding system (blade
guard assembly, riving knife and anti-kickback pawls)
for every operation for which they can be used
including all through-cutting. If you elect not to use
any of these components for a particular application,
exercise additional caution regarding control of the
workpiece, the use of push sticks, the position of your
hands relative to the blade, the use of safety glasses,
the means to avoid kickback and all other warnings
contained in this manual and on the saw itself. Replace
the guarding systems as soon as you return to throughcutting operations. Keep the guard assembly in
working order.
MAKING A PUSH STICK
In order to operate your table saw safely, you must
use a push stick whenever the size or shape of the
workpiece would otherwise cause your hands to be
within 6 inches (152 mm) of the saw blade or other
cutter. A push stick is included with this saw.
No special wood is needed to make additional push
sticks as long as they are sturdy and long enough
and the wood is free of knots, checks and cracks. A
length of 16 inches (400 mm) is recommended with a
notch that fits against the edge of the workpiece to
prevent slipping. It’s a good idea to have several push
sticks of the same minimum length, 16 inches (400
mm), with different size notches for different workpiece
thicknesses.
The shape can vary to suit your own needs as long as
it performs its intended function of keeping your hands
away from the blade. Angling the notch so the push
stick can be held at a 20- to 30-degree angle from the
saw’s table will help you to hold down the workpiece
while also moving it through the saw. Refer to diagram
in cutting aids section on page 23 of this manual.
6 7
TABLE SAW SAFETY RULES (CONTINUED)
KICKBACKS
Kickbacks can cause serious injury. A kickback occurs
when a part of the workpiece binds between the saw
blade and the rip fence, or other fixed object, and rises
from the table and is thrown toward the operator. The
risk of kickback can be minimized by attention to the
following instructions.
HOW TO REDUCE THE RISK OF
KICKBACKS AND PROTECT YOURSELF
FROM POSSIBLE INJURY:
• Be certain that the rip fence is parallel to the saw
blade.
• DO NOT rip by applying the feed force to the
section of the workpiece that will become the cutoff (free) piece. Feed force when ripping should
always be applied between the saw blade and the
fence; use a push stick for all narrow work that is 6
inches (152 mm) wide or less.
• Keep saw blade guard, riving knife and antikickback assembly in place and operating properly.
The riving knife must be in alignment with the saw
blade and the anti-kickback assembly must stop
a kickback once it has started. Check their action
before ripping by pushing the wood under the antikickback assembly. The teeth must prevent the
wood from being pulled toward the front of the saw.
If any part of assembly is not operational, return to
the nearest authorized service center for repair.
• Plastic and composite materials (like hardboard)
may be cut on your saw. However, since these are
usually quite hard and slippery, the anti-kickback
pawls may not stop a kickback. Therefore, be
especially attentive to following proper set up and
cutting procedures for ripping.
• Use saw blade guard, anti-kickback pawls, and
riving knife assembly for every possible operation,
including all through-cut sawing.
• Push the workpiece past the saw blade prior to
releasing control.
• NEVER rip a workpiece that is twisted or warped,
or does not have a straight edge to guide along the
fence.
• NEVER saw a large workpiece that cannot be
controlled.
• NEVER use the fence as a guide or length stop
when crosscutting.
• NEVER saw a workpiece with loose knots, flaws,
nails or other foreign objects.
• NEVER rip a workpiece shorter than 10 inches (254
mm).
• NEVER use a dull blade. A dull blade should be
replaced or re-sharpened.
7
POWER CONNECTIONS
POWER SOURCE
This saw is equipped with a 15-amp motor for use with
a 120-volt, 60-HZ alternating current. See instructions
below regarding proper connections for your saw.
For voltage, the wiring in a shop is as important as
the motor’s rating. A line intended only for lights may
not be able to properly carry the current needed for a
power tool motor; wire that is heavy enough for a short
distance may be too light for a greater distance; and a
line that can support one power tool may not be able to
support two or three.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
EXTENSION CORDS
A separate electrical circuit should be used for your
machines. This circuit should not be less than #12 wire
and should be protected with a 20-amp time lag fuse.
Before connecting the machine to the power line, make
sure the switch is in the “OFF” position and be sure
that the electric current is of the same characteristics
as indicated on the machine. A substantial voltage drop
will cause a loss of power and overheat the motor. It
may also damage the machine.
Never use a damaged extension cord.
Check extension cords before each
use. If damaged, replace immediately. Touching the
damaged area could case electrical shock resulting in
serious injury.
Keep the extension cord clear of the
work area. Position the cord so it will
not get caught on lumber, tools or other obstructions.
• Use proper extension cords. When using an
extension cord, be sure to use one heavy enough
to carry the current machine. An undersized cord
will cause a drop in line voltage, resulting in loss
of power and overheating. The table shows the
maximum gauge to use depending on the cord
length. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
Only round, jacketed cords listed by Underwriter’s
Laboratories (UL) should be used.
• When working with the tool outdoors, use an
extension cord designed for outside use.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC
MACHINES
AMPERE
RATING
0-6
0-6
0-6
0-6
6-10
6-10
6-10
6-10
10-12
10-12
10-12
10-12
12-16 120 Up to 25 14 AWG
12-16 120 25-50 12 AWG
12-16 120
VOLTS TOTAL LENGTH
OF CORD IN
FEET
120
120
120
120
120
120
120
120
120
120
120
120
Up to 25
25-50
50-100
100-150
Up to 25
25-50
50-100
100-150
Up to 25
25-50
50-100
100-150
GREATER THAN 50 FEET NOT
RECOMMENDED
GAUGE OF
EXTENSION CORD
18 AWG
16 AWG
16 AWG
14 AWG
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG
• Prior to tool assembly and use, read this manual
thoroughly to familiarize yourself with proper
assembly, maintenance and safety procedures.
Check shipping carton and machine for damage
before unpacking. Carefully remove components in
top foam layer. Remove the top layer of foam then
remove all components in the bottom layer of foam.
Lay out all parts on a piece of cardboard or other clean,
flat surface. Always check for and remove protective
UNPACKING
shipping materials around motors and moving parts. Do
not discard shipping carton and packing materials until
you have carefully inspected the contents, assembled
the machine and are satisfied that it operates correctly.
Compare package contents to Component Parts List
and Hardware Package List prior to assembly to make
sure all items are present. Carefully inspect parts to
make sure no damage occurred during shipping. If any
parts are missing, damaged or preassembled, do not
assemble. Instead, call Customer Support at 1-844816-8986 for assistance.
8 9
UNPACKING (CONTINUED)
SHIPPING CONTENTS
A. Saw
B. Rip Fence
C. Blade
D. Anti-Kickback Pawls
E. Blade Guard
F. Throat Plate
G. Miter Gauge
H. Stand Part 1
A B
I. Stand Part 2
J. Stand legs (4)
K. Blade Wrenches (on board storage)
L. Push Stick
M. Extension Wing
N. Fence Rail
O. Riving Knife (preassembled to saw)
C
E
D
F
G
N
IH
K
J
ML
O
9
UNPACKING (CONTINUED)
CONTENTS OF HARDWARE BAG
Description (QTY)
a. M8 x 35 mm (1 1/2 in.) Carriage Bolt (8)
b. M8 Lock Nut (8)
c. M8 Lock Nut (2)
d. M8 Flat Washer (2)
e. M8 Plastic Washer (2)
f. M8 x 65 mm (2 9/16 in.) Hex Socket Half Round
Head Screw (2)
g. M5 x 10 mm (3/8 in.) Hex Socket Cap Screw (3)
h. M5 Flat Washer (2)
i. M5 x 25 mm (1 in.) Hex Socket Cap Screw (6)
j. Shoulder Screw
k. M5 Kep Nut (2)
l. M4 Hex/Phillips Wrench
m. Knob
i
hg
c d fe
ba
TOOLS NEEDED FOR ASSEMBLY OR ADJUSTMENTS
j
m
l
(Not Supplied)
k
Phillips Screwdriver
Straight Edge
3 mm, 4 mm
Hex Key
Adjustable Wrench
Combination Square
10 11
Loading...