Porter-Cable PCC740 Instruction Manual

20V Max* 1/2 inch (12.7mm) Impact Wrench with hog ring anvil

Clé à Chocs avec enclume anneau porc de 12.7mm (1/2 po) et 20V Max*

Llave de impacto de 20V Máx* con conector Tipo anillo de ½ pulg. (13mm)

CATALOG NUMBER

N° DE CATALOGUE
Nº DE CATÁLOGO

PCC740

Instruction manual
Manuel d’ instructions
Manual de Instrucciones

www.portercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA:

LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

Thank you for choosing PORTER-CABLE! To register your new product, go to:

www.portercable.com/ServiceAndSupport/ProductRegistration.aspx

Merci d’avoir choisi PORTER-CABLE! Consulter le site Web www.portercable.com/
ServiceAndSupport/ProductRegistration.aspx pour enregistrer votre nouveau produit.

Gracias por elegir PORTER-CABLE ! Para registrar su producto, visite : www.portercable.
com/ServiceAndSupport/ProductRegistration.aspx

*Maximum initial battery pack voltage (measured without a workload) is 20 volts.
Measured under a workload, nominal voltage is 18.
*La tension initiale maximale du bloc-piles (mesurée sans charge de travail) est de 20
volts. La tension nominale est de 18.
*El máximo voltaje inicial del paquete de baterías (medido sin una carga de trabajo)
es 20 voltios. la tensión nominal es de 18.

2

General Power Tool Safety Warnings

WARNING: Read all safety

Warnings and all instructions. Failure to

follow the warnings and instructions may
result in electric shock, fire and/or serious
injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

1) WORK AREA SAFETY
a) Keep work area clean and well

lit. Cluttered or dark areas invite

accidents.

b) Do not operate power tools in

explosive atmospheres, such as in the
presence of flammable liquids, gases
or dust. Power tools create sparks

which may ignite the dust or fumes.

c)

Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose
control.

2) ELECTRICAL SAFETY
a) Power tool plugs must match the

outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.

Unmodified plugs and matching outlets
will reduce risk of electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,
radiators, ranges and refrigerators.

There is an increased risk of electric
shock if your body is earthed or
grounded.

c) Do not expose power tools to rain

or wet conditions. Water entering

a power tool will increase the risk of
electric shock.

d) Do not abuse the cord. Never use

the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts. Damaged or

entangled cords increase the risk of
electric shock.

e) When operating a power tool

outdoors, use an extension cord
suitable for outdoor use. Use of a

cord suitable for outdoor use reduces
the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a
ground fault circuit interrupter (GFCI)
protected supply. Use of a GFCI

reduces the risk of electric shock.

3) PERSONAL SAFETY
a) Stay alert, watch what you are

doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence
of drugs, alcohol or medication.

A moment of inattention while
operating power tools may result in
serious personal injury.

b) Use personal protective equipment.

Always wear eye protection.

Protective equipment such as dust
mask, nonskid safety shoes, hard
hat, or hearing protection used for
appropriate conditions will reduce
personal injuries.

c) Prevent unintentional starting.

Ensure the switch is in the off
position before connecting to
power source and/ or battery
pack, picking up or carrying the
tool. Carrying power tools with your

finger on the switch or energizing
power tools that have the switch on
invites accidents.

d)

Remove any adjusting key or wrench

before turning the power tool on.

A wrench or a key left attached to a
rotating part of the power tool may

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you
to hazardous situations and your risks of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may

result in minor or mod er ate injury.

NOTICE: Used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.

3

result in personal injury.

e) Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the
power tool in unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewelry. Keep your
hair, clothing and gloves away
from moving parts. Loose clothes,

jewelry or long hair can be caught in
moving parts.

g) If devices are provided for the

connection of dust extraction and
collection facilities, ensure these
are connected and properly used.

Use of dust collection can reduce
dust-related hazards.

4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use

the correct power tool for your
application. The correct power tool

will do the job better and safer at the
rate for which it was designed.

b) Do not use the power tool if the

switch does not turn it on and
off. Any power tool that cannot

be controlled with the switch is
dangerous and must be repaired.

c) Disconnect the plug from the

power source and/or the battery
pack from the power tool before
making any adjustments,
changing accessories, or storing
power tools. Such preventive safety

measures reduce the risk of starting
the power tool accidentally.

d) Store idle power tools out of

the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power

tools are dangerous in the hands of
untrained users.

e) Maintain power tools. Check

for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the power tool’s operation.
If damaged, have the power
tool repaired before use. Many

accidents are caused by poorly
maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.

g) Use the power tool, accessories

and tool bits, etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed.

Use of the power tool for operations
different from those intended could
result in a hazardous situation.

5) BATTERY TOOL USE AND CARE
a)

Recharge only with the charger
specified by the manufacturer. A

charger that is suitable for one type of
battery pack may create a risk of fire
when used with another battery pack.

b) Use power tools only with

specifically designated battery
packs. Use of any other battery packs

may create a risk of injury and fire.

c) When battery pack is not in use,

keep it away from other metal
objects like paper clips, coins, keys,
nails, screws, or other small metal
objects that can make a connection
from one terminal to another.

Shorting the battery terminals together
may cause burns or a fire.

d) Under abusive conditions,

liquid may be ejected from the
battery, avoid contact. If contact
accidentally occurs, flush with
water. If liquid contacts eyes,
additionally seek medical help.

Liquid ejected from the battery may
cause irritation or burns.

6) SERVICE
a) Have your power tool serviced by a

qualified repair person using only
identical replacement parts. This will

ensure that the safety of the power
tool is maintained.

SPECIFIC SAFETY RULES

• Hold power tool by insulated gripping

surfaces, when performing an
operation where the fastner may
contact hidden wiring. Fastener

contacting a “live” wire may make
exposed metal parts of the power tool
“live” and could give the operator an
electric shock.

• Wear ear protectors with impact

drivers. Exposure to noise can cause

hearing loss.

• Use clamps or another practical way

to secure and support the work piece
to a stable platform. Holding the work

by hand or against your body leaves it
unstable and may lead to loss of control.

• When not in use, place tool on its side

on a stable surface where it will not
cause a tripping or falling hazard. Some

tools with large battery packs will stand
upright but may be easily knocked over.

• Keep your hair, clothing, and gloves

away from air vents. Air vents often

cover moving parts in which these items
can be caught.

4

• Hold tool firmly with two hands. Loss

of control can cause personal injury.

•

Wear safety goggles or other eye
protection. Hammering and drilling

operations cause chips to fly. Flying particles
can cause permanent eye damage.

• Bits, sockets and tools get hot during
operation. Wear gloves when touching them.

• Do not operate this tool for long periods
of time. Vibration caused by tool action

may be harmful to your hands and arms.
Use gloves to provide extra cushion and
limit exposure by taking frequent rest
periods.

• Wear appropriate personal hearing
protection during use. Under some

conditions and duration of use, noise
from this product may contribute to
hearing loss.

WARNING: Impact wrenches are

not torque wrenches. Do not use this tool
for tightening fasteners to specified
torques. An independent, calibrated torque
measurement device such as a torque
wrench should be used when under
tightened or over tightened fasteners can
lead to the failure of the joint.

WARNING: ALWAYS use safety

glasses. Everyday eyeglasses are NOT
safety glasses. Also use face or dust
mask if drilling operation is dusty.
ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/

CPA Z94.3),

•

ANSI S12.6 (S3.19) hearing protection,

• NOSH/OSHA respiratory protection.

WARNING: Always wear proper

personal hearing protection that
conforms to ANSI S12.6 (S3.19) during
use. Under some conditions and duration

of use, noise from this product may
contribute to hearing loss.

WARNING:

Some dust created by
power sanding, sawing, grinding, drilling,
and other construction activities contains
chemicals known to the state of California to
cause cancer, birth defects or other
reproductive harm. Some examples of these
chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and

cement and other masonry products,
and

• arsenic and chromium from
chemically-treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: work in a well ventilated
area, and work with approved safety
equipment, such as those dust masks

that are specially designed to filter out
microscopic particles.

• Avoid prolonged contact with dust
from power sanding, sawing, grinding,
drilling, and other construction
activities. Wear protective clothing
and wash exposed areas with soap
and water. Allowing dust to get into

your mouth, eyes, or lay on the skin
may promote absorption of harmful
chemicals.

WARNING: Use of this tool can

generate and/or disperse dust, which
may cause serious and permanent
respiratory or other injury. Always use
NOSH/OSHA approved respiratory
protection appropriate for the dust
exposure. Direct particles away from face
and body.

Symbols

The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:

V ..................volts

A ..................amperes

Hz ................ hertz

W .................watts

min ..............minutes

or AC ...... alternating current

or DC ...direct current

n

o ................ no load speed

................Class I Construction

................earthing terminal

(grounded)

............... safety alert symbol

................Class II Construction

(double insulated)
.../min or rpm...revolutions or
reciprocation per minute

..............Read instruction manual

before use

................ Use proper respiratory

protection

...............Use proper eye protection

................ Use proper hearing

protection

BPM ...........beats per minute

IPM ...........impacts per minute

• When using an extension cord, be
sure to use one heavy enough to carry
the current your product will draw. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. The following table
shows the correct size to use depending
on cord length and nameplate ampere
rating. If in doubt, use the next heavier
gauge. The smaller the gauge number,
the heavier the cord.

5

IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGERS

SAVE THESE INSTRUCTIONS: This
manual contains important safety
instructions for battery chargers.

WARNING: Before using charger,

read all instructions and cautionary
markings on charger, battery pack, and
product using battery pack.

• Shock hazard. Do not allow any liquid

to get inside charger.

• Burn hazard. To reduce the risk

of injury, charge only designated
PORTER-CABLE batteries. Other types
of batteries may burst causing personal
injury and damage.

• Under certain conditions, with the
charger plugged in to the power
supply, the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil, or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger
before attempting to clean.

• DO NOT attempt to charge the battery

pack with any chargers other than the
ones in this manual. The charger and

battery pack are specifically designed to
work together.

•

These chargers are not intended for any
uses other than charging designated
PORTER-CABLE rechargeable
batteries. Any other uses may result in

risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when

disconnecting charger. This will reduce
risk of damage to electric plug and cord.

• Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.

• Do not use an extension cord
unless it is absolutely necessary.

Use of improper extension cord could
result in risk of fire, electric shock, or
electrocution.

• An extension cord must have
adequate wire size (AWG or American
Wire Gauge) for safety. The smaller

the gauge number of the wire, the
greater the capacity of the cable, that
is 16 gauge has more capacity than
18 gauge. When using more than one
extension to make up the total length, be
sure each individual extension contains
at least the minimum wire size.

• Do not place any object on top of
charger or place the charger on a soft
surface that might block the ventilation
slots and result in excessive internal
heat. Place the charger in a position
away from any heat source. The

charger is ventilated through slots in the
top and the bottom of the housing.

• Do not operate charger with damaged cord
or plug — have them replaced immediately.

• Do not operate charger if it has
received a sharp blow, been dropped,
or otherwise damaged in any way.

Take it to an authorized service center.

• Do not disassemble charger; take it
to an authorized service center when
service or repair is required. Incorrect
reassembly may result in a risk of
electric shock, electrocution or fire.

• Disconnect the charger from the
outlet before attempting any cleaning.

This will reduce the risk of electric shock.
Removing the battery pack will not
reduce this risk.

• NEVER attempt to connect 2 chargers
together.

• The charger is designed to operate on
standard household electrical power
(120 Volts). Do not attempt to use it on
any other voltage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY PACKS

WARNING:

For safe operation, read
this manual and manuals originally supplied
with tool before using the battery pack.

The battery pack is not fully charged out of
the carton. Before using the battery pack and
charger, read the safety instructions below.
Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not incinerate the battery pack

even if it is severely damaged or is
completely worn out. The battery pack

can explode in a fire. Toxic fumes and
materials are created when Li-Ion battery
packs are burned.

• Do not charge or use battery in

explosive atmospheres, such as in the
presence of flammable liquids, gases
or dust. Inserting or removing the battery

from the charger may ignite the dust or
fumes.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

Ampere Rating

More Not more American Wire Gage
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

• I

f battery contents come into contact
with the skin, immediately wash area
with mild soap and water. If battery liquid

gets into the eye, rinse water over the
open eye for 15 minutes or until irritation
ceases. If medical attention is needed,
the battery electrolyte for Li-Ion batteries
is composed of a mixture of liquid organic
carbonates and lithium salts.

• Contents of opened battery cells may
cause respiratory irritation. Provide

fresh air. If symptoms persists, seek
medical attention.

WARNING:

Burn hazard. Battery liquid

may be flammable if exposed to spark or flame.

• Charge the battery packs only in
PORTER-CABLE chargers.

• DO NOT splash or immerse in water
or other liquids. This may cause

premature cell failure.

• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 105°F (40˚C) (such
as outside sheds or metal buildings in
summer).

WARNING:

Never attempt to open

the battery pack for any reason. If battery
pack case is cracked or damaged, do not
insert into charger. Do not crush, drop or
damage battery pack. Do not use a battery
pack or charger that has received a sharp
blow, been dropped, run over or damaged in
any way (i.e., pierced with a nail, hit with a
hammer, stepped on). Damaged battery
packs should be returned to service center
for recycling.

WARNING:

Fire hazard. Do not

store or carry battery so that metal
objects can contact exposed battery
terminals. For example, do not place

battery in aprons, pockets, tool boxes,
product kit boxes, drawers, etc., with loose
nails, screws, keys, etc. Transporting

batteries can possibly cause fires if the
battery terminals inadvertently come in
contact with conductive materials such
as keys, coins, hand tools and the like.

The US Department of Transportation
Hazardous Material Regulations (HMR)
actually prohibit transporting batteries in
commerce or on airplanes (i.e., packed in
suitcases and carry-on luggage) UNLESS
they are properly protected from short
circuits. So when transporting individual
batteries, make sure that the battery
terminals are protected and well insulated
from materials that could contact them and
cause a short circuit. NOTE: Li-Ion

batteries should not be put in checked
baggage.

NOTE: Do not store the battery packs in
a tool with the trigger switch locked on.

Never tape the trigger switch in the ON
position.

NEVER force the battery pack into the
charger. DO NOT modify the battery pack
in any way to fit into a non-compatible
charger as battery pack may rupture
causing serious personal injury.

Storage Recommendations

1. The best storage place is one that is
cool and dry away from direct sunlight
and excess heat or cold.

2. Long-term storage will not harm the
battery pack or the charger as long as the
battery is not depleted.

Charging Procedure

PORTER-CABLE chargers are designed

to charge PORTER-CABLE battery
packs. Charge times are: PCC690L in
40-80 mins., PCC699L /PCC691L in
70-140 mins., PCC692/PCC692L in 40-80
mins., and PCC695L in 180-360 mins.
depending on the pack being charged.

1. Plug the charger into an appropriate
outlet before inserting the battery pack.

2. Insert the battery pack into the charger.

3. The LED will flash indicating that
the battery is being charged.

4. The completion of charge is

indicated by the LED remaining on
continuously. The pack is fully charged and
may be used at this time or left on the charger.

Recharge discharged batteries as soon
as possible after use or battery life
may be greatly diminished. For longest
battery life, do not discharge batteries
fully. It is recommended that the batteries

be recharged after each use.

Charger Diagnostics

This charger is designed to detect certain
problems that can arise with the battery packs
or the power source. Problems are indicated
by one LED flashing in different patterns.

Bad Battery

The charger can detect a weak or

damaged battery. The LED flashes in
the pattern indicated on the label. If you see
this bad battery blink pattern, do not continue
to charge the battery. Return it to a service
center or a collection site for recycling.

Hot/Cold Pack Delay

When the charger detects a battery

that is excessively hot or excessively
cold, it automatically starts a Hot/Cold
Pack Delay, suspending charging until the
battery has normalized. After this happens,
the charger automatically switches to the
Pack Charging mode. This feature ensures
maximum battery life. The light flashes in
the pattern indicated on the label.

6

Problem Power Line

When the charger is used with some
portable power sources such as

generators or sources that convert
DC to AC, the charger may temporarily
suspend operation. The LED flashes in the
pattern indicated on the label. This indicates
that the power source is out of limits.

Leaving the Battery in the Charger

The charger and battery pack can be
left connected with the LED glowing
indefinitely. The charger will keep the
battery pack fresh and fully charged.
This charger features an automatic tune­up mode which equals or balances the
individual cells in the battery pack to allow
it to function at peak capacity. Battery
packs should be tuned up weekly or
whenever the battery no longer delivers the
same amount of work. To use the automatic
tune-up mode, place the battery pack in the
charger and leave it for at least 8 hours.

Important Charging Notes

1. Longest life and best performance can
be obtained if the battery pack is charged
when the air temperature is between 65°F
and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below
+40°F (+4.5°C), or above +105°F (+40.5°C).
This is important and will prevent serious

damage to the battery pack.

2. The charger and battery pack may
become warm to touch while charging.
This is a normal condition, and does
not indicate a problem. To facilitate the
cooling of the battery pack after use,
avoid placing the charger or battery pack
in a warm environment such as in a metal
shed, or an uninsulated trailer.

3. If the battery pack does not charge
properly:

a. Check current at receptacle by
plugging in a lamp or other appliance
b. Check to see if receptacle is
connected to a light switch which turns
power off when you turn out the lights.
c. Move charger and battery pack to a
location where the surrounding air
temperature is approximately 65°F ­75°F (18°- 24°C).
d. If charging problems persist, take
the tool, battery pack and charger to
your local service center.

4. The battery pack should be recharged
when it fails to produce sufficient power
on jobs which were easily done previously.
DO NOT CONTINUE to use under these
conditions. Follow the charging procedure.
You may also charge a partially used pack
whenever you desire with no adverse
affect on the battery pack.

7

FUNCTIONAL DESCRIPTION
Figure A

1. Trigger Switch

2. Forward/Reverse Button

3. 1/2” Hog Ring Anvil

4. Battery

5. Battery Release Button

6. LED Work Light

This product uses the batteries and chargers listed below.

20V Max* Lithium-Ion Batteries: PCC680L, PCC681L, PCC682/PCC682L, PCC685L
20V Max* Lithium-Ion Chargers: PCC690L, PCC691L, PCC692/PCC692L, PCC695L, PCC699L

2

1

3

4

6

5

Operating Instructions

WARNING: Shock hazard. Under

no circumstances should this product be
used near water.

WARNING: Risk of lacerations or

burns. Do not touch work piece or

accessory immediately after operating the
tool. They can become very hot. Handle
carefully. Always allow accessories and
work piece to cool before handling.

Installing and Removing the
Battery Pack From the Tool

WARNING:

To reduce the risk of
serious personal injury, turn tool off and
remove the battery pack before making
any adjustments or removing/installing
attachments or accessories. An accidental

start-up can cause injury.

CAUTION:

Make certain the lock-off
button is engaged to prevent switch actuation
before removing or installing battery.

TO INSTALL BATTERY PACK: Insert
battery pack (4) firmly into tool until an
audible click is heard as shown in Figure
B. Ensure battery pack is fully seated and
fully latched into position.

TO REMOVE BATTERY PACK: Depress
the battery release button (5) as shown in

Figure C and pull battery pack out of tool.

Variable Speed Trigger Switch

The tool is turned ON and OFF by
squeezing and releasing the trigger switch
(1). The farther the trigger is depressed,
the higher the speed of the tool.

• To turn the tool on, squeeze the trigger
switch (1).

• To turn the tool off, release the trigger
switch. Your tool is equipped with a
brake. The tool will stop as soon as the
trigger switch is fully released.

NOTE:

Continuous use in variable
speed range is not recommended. It
may damage the switch and should be
avoided.

Forward/Reverse Button

A forward/reverse control button (2)
determines the rotational direction of the
tool and also serves as a lock off button.

• To select forward rotation, release the

trigger switch and depress the forward/
reverse control button on the right side
of the tool.

• To select reverse, depress the forward/

reverse control button on the left side of
the tool.

• The center position of the control button

locks the tool in the off position. When
changing the position of the control
button, be sure the trigger is released.

Attaching Accessories

WARNING:

To reduce the risk of
serious personal injury, turn tool off and
remove the battery pack before making
any adjustments or removing/installing
attachments or accessories. An accidental

start-up can cause injury.

CAUTION: Use only impact

sockets. Non-impact sockets may break
and cause a hazardous condition. Inspect
socket prior to use to ensure that it
contains no cracks.

To install an accessory, firmly push
accessory onto the 1/2” hog ring anvil
(3) as shown in figure D. The hog ring
(3) compresses to allow the accessory to
slide on. After the accessory is installed,
the hog ring applies pressure to help
provide accessory retention.

8

C

B

D

To remove an accessory, grasp the
accessory and firmly pull it off.

Usage

WARNING: Ensure fastener and/or

system will withstand the level of torque
generated by the tool. Excessive torque
may cause breakage and possible
personal injury.

1. Place the accessory on the fastener
head. Keep the tool pointed straight at
the fastener.

2. Squeeze the trigger switch (1) to start
operation. Always check torque with a
torque wrench, as the fastening torque
is affected by many factors including the
following:

• Accessory size: Failure to use the
correct accessory size will cause a
reduction in fastening torque.

• Bolt Size: Larger bolt diameters
generally require higher fastening
torque. Fastening torque will also vary
according to length, grade, and torque
coefficient.

• Bolt: Ensure that all threads are free of
rust and other debris to allow proper
fastening torque

• Material: The type of material and
surface finish of the material will affect
fastening torque.

• Fastening Time: Longer fastening
time results in increased fastening
torque. Using a longer fastening time
than recommended could cause the
fasteners to be overstressed, stripped or
damaged.

Capacity

Your 1/2” (12.7 mm) impact wrench uses
sockets with 1/2” (12.7 mm) square drive
ends.

LED Work Light

When drill is activated by squeezing the
trigger switch (1), the integrated LED work
light (6) will automatically illuminate the
work area and will automatically turn off
after the trigger switch is released. If the
trigger switch remains depressed, the work
light will remain on.

NOTE: The work light is for lighting
the immediate work surface and is not
intended to be used as a flashlight.

Cleaning

WARNING:

To reduce the risk of
serious personal injury, turn tool off and
remove the battery pack before making

9

any adjustments or removing/installing
attachments or accessories. An accidental

start-up can cause injury.

WARNING: Blow dirt and dust out

of all air vents with clearn, dry air at least
once a week. To minimze the risk of eye
injury, always wear ANSI Z87.1 approved
eye protection when performing this.

WARNING: Never use solvents or

other harsh chemicals for clearning the
non-metallic parts of the tool. These
chemicals may weaken the plastic
materials used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.

Charger Cleaning
Instructions

WARNING:

Shock hazard.
Disconnect the charger from the AC outlet
before cleaning.

Dirt and grease may be removed from the
exterior of the charger using a cloth or soft
non-metallic brush. Do not use water or
any cleaning solutions.

Replacement Parts

Use only identical replacement parts. For a
parts list or to order parts, visit our service
website at www.portercable.com. You
can also order parts from your nearest
PORTER-CABLE Factory Service Center or
PORTER-CABLE Authorized Warranty Service
Center. Or, you can call our Customer Care
Center at [phone].

The RBRC® Seal

The RBRC® (Rechargeable
Battery Recycling Corp oration)
Seal on the nickel cadmium,
nickel metal hydride or lithium­ion batteries (or battery packs)
indicates that the costs to recycle these
batteries (or battery packs) at the end of
their useful life have already been paid
by BLACK+DECKER. In some areas, it
is illegal to place spent nickel cadmium,
nickel metal hydride or lithium-ion
batteries in the trash or municipal solid
waste stream and the Call 2 Recycle®
program provides an environmentally
conscious alternative.
Call 2 Recycle, Inc., in cooperation with
BLACK+DECKER and other battery
users, has established the program in the
United States and Canada to facilitate
the collection of spent nickel cadmium,
nickel metal hydride or lithium-ion
batteries. Help protect our environment

10

and conserve natural resources by
returning the spent nickel cadmium, nickel
metal hydride or lithium-ion batteries
to an authorized BLACK+DECKER
service center or to your local retailer for
recycling. You may also contact your local
recycling center for information on where
to drop off the spent battery. RBRC® is a
registered trademark of Call 2 Recycle,
Inc.
This Class B digital apparatus complies
with Canadian ICES-003.

This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept
any interference received, including
interference that may cause undesired
operation.

NOTE: This equipment has been tested
and found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation.

If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:

• Reorient or relocate the receiving
antenna.

• Increase the separation between the
equipment and receiver.

• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced
radio/TV technician for help.

Changes or modifications to this unit
not expressly approved by the party
responsible for compliance could void the
user’s authority to operate the equipment.
This Class B digital apparatus complies
with Canadian ICES-003.

Service and Repairs

All quality tools will eventually require
servicing and/or replacement of parts.
For information about PORTER-CABLE,
its factory service centers or authorized
warranty service centers, visit our website
at www.portercable.com or call our
Customer Care Center at [phone].
All repairs made by our service centers
are fully guaranteed against defective
material and workmanship. We cannot
guarantee repairs made or attempted
by others. You can also write to us for
information at PORTER-CABLE, 4825
Highway 45 North, Jackson, Tennessee
38305, [phone] - Attention:
Product Service. Be sure to include all of
the information shown on the nameplate
of your tool (model number, type, serial
number, etc.).

Accessories

WARNING: Since accessories,

other than those offered by PORTER­CABLE, have not been tested with this
product, use of such accessories with this
tool could be hazardous. To reduce the
risk of injury, only PORTER-CABLE
recommended accessories should be
used with this product.
A complete line of accessories is
available from your PORTER-CABLE
Factory Service Center or a PORTER­CABLE Authorized Warranty Service
Center. Please visit our Web Site www.
portercable.com for a catalog or for the
name of your nearest supplier.

11

Troubleshooting

Problem Possible Cause Possible Solution

• Unit will not start. • Battery pack not installed properly. • Check battery pack
installation.

• Battery pack not charged. • Check battery pack
charging requirements.

• Internal components too hot. • Allow tool to cool down.

•

Battery pack will not charge.

•

Battery pack not inserted into charger.

• Insert battery pack into
charger until LED
lights.

• Charger not plugged in. • Plug charger into a
working outlet. Refer to
“Important Charging Notes”
for more details.

• Surrounding air temperature • Move charger and battery
too hot or too cold. pack to a surrounding air
temperature of above 40
degrees F (4,5°C) or below
105 degrees F (+40,5°C).

• Unit shuts off abruptly. • Battery pack has reached its • Allow battery pack to cool

maximum thermal limit. down.

• Out of charge. ( To • Place on charger and

maximize the life of the allow to charge.
battery pack it is designed
to shutoff abruptly when
the charge is depleted.)

For assistance with your product, visit our website at www.portercable.com for a list of
service centers, or call the PORTER-CABLE Customer Care Center at [phone].

THREE YEAR LIMITED
WARRANTY

PORTER-CABLE will repair or replace,
without charge, any defects due to faulty
materials or workmanship for three years
from the date of purchase for tools (two
years for batteries). This warranty does
not cover part failure due to normal
wear or tool abuse. For further detail of
warranty coverage and warranty repair
information, visit www.portercable.com
or call [phone]. This warranty
does not apply to accessories or damage
caused where repairs have been made or
attempted by others. This warranty gives
you specific legal rights and you may
have other rights which vary in certain
states or provinces.
In addition to the warranty, PORTER­CABLE tools are covered by our:
1 YEAR FREE SERVICE: PORTER­CABLE will maintain the tool and replace
worn parts caused by normal use, for
free, any time during the first year after
purchase.
90 DAY MONEY BACK GUARANTEE: If
you are not completely satisfied with the
performance of your PORTER-CABLE

Power Tool for any reason, you can return
it within 90 days from the date of purchase
with a receipt for a full refund – no questions
asked.
LATIN AMERICA: This warranty does not
apply to products sold in Latin America.
For products sold in Latin America, see
country specific warranty information
contained in the packaging, call the local
company or see website for warranty
information.
To register your tool for warranty service
visit our website at www.portercable.com.

WARNING LABEL REPLACEMENT

If your WARNING labels become illegible
or are missing, call [phone] for a
free replacement.

4825 Highway 45 North

Jackson, Tennessee 38305

[phone]

www.portercable.com